SPL Supreme JET DRY EXECUTIVE II Instruction Manual

Supreme JET DRY EXECUTIVE II
MAINTENANCE GUIDELINES
Daily Cleaning Guidelines
PLEASE READ THE FOLLOWING GUIDELINES TO ENSURE THE SMOOTH RUNNING AND
LONGEVITY OF YOUR SUPREME JET DRYER EXECUTIVE II HAND DRYER.
Weekly Cleaning Recommendations
HEPA and Lint Pre-Filter Replacements (6 monthly)
Control Panel Display
DAILY CLEANING GUIDELINES
1. Switch the machine off at the wall or use the switch above the water
collection tray.
NOTE: If you are using the machine’s ON/OFF switch it is the larger one
of the two.
2. Empty the water collection tray. To unlock the water tray slide the lock
tab across. Remove the water tray and rinse with warm water.
3. Wipe down the machine using a warm damp cloth and a surface cleaner.
NOTE: Cleaning should be performed daily using a soft cloth and non-
abrasive and non-caustic cleaning fluid to prevent malfunctions or
damage to the unit.
Do not spray water directly into the machine.
It is recommended to wear protective gloves during cleaning.
Turn the power switch back on, then replace the water tray and lock.
1

WEEKLY CLEANING RECOMMENDATIONS
Weekly cleaning requirements in addition to daily cleaning
1. Pour a cup of warm water down the drain hole in the
drying chamber.
2. Gently scrub the drain hole inside the drying chamber
with a cleaning brush. Then check the water tray is
empty and wipe down machine as per daily cleaning
guidelines.
3. Remove the water tray and empty it. Then remove
the lid of the water tray and rinse with warm water.
Pay particular attention to removing soap scum from
the two terminals.
4. Remove lint pre-filter holder located below water
tray. Gently snap open the holder and crush away
any lint on the filter. Then put the filter back
together before placing both the lint pre-filter and
water tray back into the machine. Turn power back
on.
Please note: It is recommended to replace your lint
pre-filter every six months when you change your
HEPA filter.
2

HEPA AND LINT PRE-FILTER REPLACEMENTS (6 monthly)
3
1. Slide the lock tab across and remove the water tray.
Turn the machine off at the wall. If your machine does
not have an external switch then use the large ON/OFF
switch just above the water tray.
2. Remove the lint pre-filter by pulling it out towards you.
3. Replace the lint pre-filter by gently snapping open the
holder. Take out the old lint pre-filter and replace it with
the new one. Then gently snap the lint pre-filter holder
back together.
4. Remove the HEPA filter by pulling the black holder
downwards.
6. Turn machine back on. Put the filter holder back into the
machine. This will reset the machine counter.
NOTE: The holder is marked “front”. This should face
you when fitting the holder.
Put the lint pre-filter and water tray back into the
machine and lock the tab again.
5. Take the old HEPA filter and freshener pod out of the
holder and replace with the new ones.
NOTE: Do not discard the holder.
FAILURE TO REPLACE FILTERS ON TIME MAY INTERUPT AIR FLOW AND OVERHEAT THE MOTOR, IN THIS CASE
THE WARRANTY WILL BE INVALIDATED.

4
CONTROL PANEL DISPLAY
1. When you turn your Supreme Jet Dry Executive II on you
will notice a LED display on the top panel. This symbolises
that it is ready for operation.
2. The blue dots will spin when the machine is in operation.
3. The ‘Water Tank’ icon symbolises that the water tank is
full and needs emptying (follow weekly cleaning
recommendations.)
4. The HEPA filter icon will begin to flash when the HEPA
filter and the lint pre-filter need changing. The machine is
designed to stop working shortly after this light has began
flashing. Once the HEPA filter is replaced it will reset your
machine.
It is recommended that you change the HEPA filter every
six months.
TO ORDER YOUR REPLACEMENT HEPA FILTER PLEASE PHONE SPL 07 823 5790