SportIQ Smart Tag ST008 User manual

SportIQ Smart Tag
User Manual
In the box, you'll find:
- SportIQ Smart Tag.
- This user manual.
You'll also need
- A smart device compatible with Bluetooth v4.0
(Bluetooth Low Energy) technology using iOS
(v12.2 or later) or Android (v7.0 'Nougat' or later)
operating system.
- A SportIQ-enabled App which can be freely
downloaded from Apple App store™ for iOS and
Google play™ for Android.
Quick start guide
1. Check the setting of your smart device to
make sure that its Bluetooth radio is
enabled.
2. Launch SportIQ-enabled App on your
smart device.
3. Firmly shake SportIQ Smart Tag in your
hand to activate it.
4. Follow on-screen instructions to use
SportIQ Smart Tag.
Troubleshooting
1. SportIQ Smart Tag fails to connect to the
SportIQ-enabled App.
- Verify that the Bluetooth connection of your smart
device is activated and supports BLE devices.
- Tag activation sequence is purposely set to high
acceleration levels to prevent battery drain due to
unwanted tag activations. Try to activate the tag
again.
- Try to close SportIQ-enabled App completely
(including its inactive state at the background of
your operating system) and restart it. At the same
time, reactivate the Bluetooth radio of your smart
device. Make sure to reactivate the tag after the
restart to make sure that the tag has not gone to
sleep mode.
- Check that your smart device uses the latest
software versions of the operating system and
SportIQ-enabled App. Sometimes the operating
system (iOS and Android) handles Bluetooth
connections unexpectedly and updates often
improve the robustness of Bluetooth connections.
- The battery of the tag might have drained out.
2. SportIQ Smart Tag appears on the SportIQ-
enabled App screen but it unexpectedly
disconnects or fails to send data.
- Make sure that your smart device hasn't exceeded
its maximum number of Bluetooth connections.
Bluetooth connections are sometimes unreliable if
the tag is used in a location with a great number of
other WiFi or Bluetooth signals.
- Make sure that the tag stays within the specified
maximum range for Bluetooth low energy devices.
In open areas, the maximum range is approximately
100 m / 330 ft. Typically, ranges below 33 m / 100 ft
should not cause problems if there are no solid
objects between the tag and the smart device.
- The battery of the tag might have drained out.
3. SportIQ-enabled App fails to analyze data with
expected accuracy.
- The built-in accelerometer should be calibrated
from time to time to prevent accuracy loss.
Especially so, if the tag is used in temperatures far
from nominal room temperatures. Follow the
instructions given by the SportIQ-enabled App to
calibrate your tag.

Recycle
Always return your used electronic products,
batteries, and packaging materials to dedicated
collection points. This way you help prevent
uncontrolled waste disposal and promote the
recycling of materials.
The crossed-out wheeled-bin symbol on
your product, battery, literature, or packaging
reminds you that all electrical and electronic
products and batteries must be taken to separate
collection at the end of their working life. This
requirement applies in the European Union. Do not
dispose of these products as unsorted municipal
waste: take them for recycling. For more information
on your nearest recycling point, please check with
your local waste authority.
Regulatory and Other Notices
ST008 / SportIQ Smart Tag:
FCC ID: 2ACY5ST8
IC: 12258A-ST8
Model: ST008
Made in China
A product that contains the ST008 / SportIQ Smart
Tag will have a permanent label affixed to it that
shows “Contains FCC ID: 2ACY5ST8” and
“Contains IC: 12258A-ST8” according to FCC & IC
labeling requirements.
FCC
Federal Communication Commission Interference
Statement
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment
and receiver.
● Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV
technician for help.
FCC Caution:
Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed
portable and mobile exposure host.
This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
Important Note:
The modular will only installed into non-metallic, DC
or battery powered product like installed into
basketball or non-metallic, DC or battery powered
sports equipment. Non-metallic, DC or battery
powered sports equipment of the host device which
install this modular with limit modular approval
should perform the test of radiated emission and
spurious emission according to FCC part 15.247
and FCC part 15.209 requirement, only if the test
result comply with FCC part 15.247 and FCC part
15.209 requirement, then the host can be sold
legally.
End Product Labeling
This transmitter module is authorized for use
portable and mobile exposure. The final end product
must be labeled in a visible area with the following:
Contains FCC ID: 2ACY5ST8.
Manual Information to the End User
The OEM integrator has to be aware not to provide
information to the end user regarding how to install
or remove this RF module in the user’s manual of
the end product which integrates this module.
The end user manual shall include all required
regulatory information/warning as show in this
manual.

Industry Canada
This device complies with Industry Canada license-
exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not
cause interference, and (2) this device must accept
any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Radiation Exposure Statement
This equipment complies with Canada radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed
portable and mobile exposure host.
Déclaration d'exposition aux radiations
Cet équipement est conforme Canada limites
d'exposition aux radiations dans un environnement
non contrôlé. Ce matériel devrait être installée
l'exposition portatifs et mobiles
This device is intended only for OEM integrators
under the following condition:
● The transmitter module may not be co-located
with any other transmitter or antenna.
Cet appareil est conçu uniquement pour les
intégrateurs OEM dans les conditions suivantes:
● Le module émetteur peut ne pas être coïmplanté
avec un autre émetteur ou antenne.
Important Note:
The modular will only installed into non-metallic, DC
or battery powered product like installed into
basketball or non-metallic, DC or battery powered
sports equipment. Non-metallic, DC or battery
powered sports equipment of the host device which
install this modular with limit modular approval
should perform the test of radiated emission and
spurious emission according to RSS-247 and RSS-
Gen requirement, only if the test result comply with
RSS-247 and RSS-Gen requirement, then the host
can be sold legally.
Note Importante:
Les modules de seront installés dans des produits
non métalliques, dc ou basket comme installés dans
des piles ou batteries non métalliques, dc ou les
équipements sportifs.minéraux non métalliques, dc
ou équipements sportifs de la batterie qui installent
ce dispositif d'accueil limite modulaire approbation
modulaire avec des émissions rayonnées et
effectuer l'essai des rayonnements non essentiels
selon rss-247 et le cnr - gen, seulement si le résultat
d'essai conforme rss-247 et le cnr - gen, puis l'hôte
peut être vendu légalement.
End Product Labeling
The final end product must be labeled in a visible
area with the following: Contains IC: 12258A-ST8.
Plaque signalétique du produit final
Le produit final doit être étiqueté dans un endroit
visible avec l'inscription suivante: Contient des IC:
12258A-ST8.
Manual Information to the End User
The OEM integrator has to be aware not to provide
information to the end user regarding how to install
or remove this RF module in the user’s manual of
the end product which integrates this module.
The end user manual shall include all required
regulatory information/warning as show in this
manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas
fournir des informations à l'utilisateur final quant à la
façon d'installer ou de supprimer ce module RF
dans le manuel de l'utilisateur du produit final qui
intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les
informations réglementaires requises et
avertissements comme indiqué dans ce manuel.
Declaration of Conformity
Hereby, SportIQ declares that this ST008 product is
in compliance with the essential requirements and
other relevant provisions of Directive 2011/65/EC
and 2014/53/EU. A copy of the Declaration of
Conformity can be found at:
http://www.sportiq.fi/declaration_of_conformity