SpraySense Anti-Bark Collar User manual

1
1
This revolutionary product allows you to
combine innovative technology with prov-
en behavior modification techniques. By
purchasing this product, you are well on
your way to gaining control over your
dog’s problem barking.
The SpraySense™ Anti-Bark Collar has
been clinically proven to be 88% effective
at stopping or reducing barking. The burst
of spray acts on four of your dog’s five
senses – it hears it, sees it, feels it and
smells it. This training process occurs
instantaneously and without pain.
Ready for your dog to become a quiet
family member? Let’s get started.

2
1
Spray device with ON/OFF switch
24” adjustable nylon collar, Quick-snap
buckle and Keeper
Can of Premier branded stain-free,
hypoallergenic spray
6-volt battery
Lifetime Warranty
Microphone
Keeper
(comes attached
to collar)
Battery
Compartment
Nylon
Collar
Fill Port
Spray Valve
Quick-Snap Buckle
This kit includes:
2
ON/OFF
Switch

3
1
Preparing the collar
Attach the spray device to the strap
Remove the keeper from the strap. (figure 1)
Orient the device so that the fill port and
spray valve are facing up and battery
compartment is facing you. (figure 2)
Grasp the strap in your right hand. Thread the
strap from back to front through the ear on the
right. Bring the strap around the front/face
and then thread it front to back through
the ear on the left. Make sure not to cover
the microphone with the strap. (figure 3)
Put the Keeper back on the strap. The tapered
edge of the Keeper should face the inside.
Now it’s time to attach the quick-snap buckle
to the strap. Feed the free edge of the strap
into the slot that is closest to the center,
starting on the inside of the curve. Next, feed
the free end through the slot on the edge of
the buckle. (figure 4)
figure 1
figure 2
figure 3
figure 4

4
4
Pass the loose strap through the keeper.
Failure to do so will increase the likelihood
that the strap will slip causing a need to
constantly adjust the fit. The assembled
collar should look as shown. (figure 5)
Fill the spray reservoir
Grasp the spray device with the fill port facing up.
Turn the spray can upside down and place the nozzle
in the fill port. (figure 6) Using firm pressure,
push down on the can and hold for 15 seconds.
Repeat and hold for an additional 5 seconds
to fully fill the reservoir. If spray is escaping
as you attempt to fill, increase the downward
pressure on the can to get a better seal. You
cannot overfill the device. When completely filled,
there should be approximately 25 sprays in the reservoir.
Insert the battery
Remove the battery compartment cover. Make
sure the + on the battery lines up with the
+ in the battery compartment. (figure 7)
Replace the compartment cover. An ON/OFF
switch is located at the bottom of the device.
If the battery is in and the device is ON, it’s
‘listening’. To prolong battery life, make sure
that you turn the device OFF when it’s not in use.
Test the spray device
Before every use, it’s best to test the spray
action by turning it ON and blowing into the
microphone.
figure 5
figure 6
figure 7
figure 8

5
Please sure read through the entire guide before putting the collar on
your dog for the first time. It’s important to start any training process
on a day when you have ample time to be with your dog so that you
can focus on your dog’s response and reward good behavior.
Fit the training collar to your dog
Remove all other collars. Place the spray collar around your dog’s neck
so that the spray valve is directed upward toward the dog’s muzzle.
Adjust the collar to fit properly. You should be able to slip two fingers under
the new collar. After it’s been fitted you may want to remove the excess strap
length. Should you choose to cut the strap, be sure to heat seal the end
to prevent fraying.
Caution Don’t leave your dog unattended wearing the training
collar until it’s accustomed to the spray device and you’ve deter-
mined that the collar is fitted properly and working correctly.
Using the collar as a training tool
A good way to observe your dog’s response to the
spray is to put your dog in a situation where
it usually barks. When your dog barks, the
device should spray. (figure 9) Your dog
will probably act a bit surprised and stop
barking. It may jump to get away from the
spray, or shake its head, or sneeze. Do not
yell “NO” or say anything when your dog barks.
When your dog stops barking, say, “good quiet.”
When the stimulus that causes your dog to bark
is present, but your dog is not barking, be sure to reward the desired
behavior with verbal praise “good quiet” and a food reward.
If you say “good quiet” and give a treat, your dog will soon start to
associate “good quiet” with not barking. After repeatedly pairing the
quiet behavior with the words “good quiet,” you can expect your dog
to stop barking with the verbal request for “quiet.”
figure 9
Getting your dog
acquainted with the collar

6
It’s very important that you take the collar off and refill the spray
reservoir before it runs dry. Otherwise you have taught your dog that
if it’s persistent, it’ll be rewarded by getting rid of the spray. To
avoid this, routinely refill the spray reservoir before every use. The
reservoir will hold approximately 25 sprays.
Where the collar can be used
The collar can be used anywhere you find your dog’s prolonged
nuisance barking to be a problem. The collar can be used indoors
or out. The spray is organic and non-toxic to humans, animals,
and the environment.
We strongly recommend that your dog is given free time without the
collar to play and relax. This collar should not be left on dogs 24
hours-a-day.
Caution Don’t use this collar while your dog is swimming or
exposed to prolonged water spray. The spray device is water
resistant, but not waterproof, and may stop working if submerged
in water. In addition, don't expose the spray device to either
freezing temperatures or conditions warmer than 110° F. Be
particularly careful not to leave the device in direct sunlight, by
a window or in a car on a summer day.
6

7
Removing the collar
Detach the collar with the quick-snap release. Remember to turn the
device OFF after every use to maximize battery life.
Purchasing spray refills
and/or batteries
Batteries, citronella and scentless spray
refills are available for purchase. (figure 11)
Check your local pet store or contact our cus-
tomer service department at 888.640.8840 for
more information.
Note Only Premier branded spray refills should be used to fill
the spray reservoir.
Enjoy your quiet dog
Your dog will quickly and painlessly learn that there is a conse-
quence for barking. It should completely assimilate to the collar
within a few days.
The SpraySense Anti-Bark Collar is the most effective tool to stop
problem barking. We’ve received countless letters and calls from
veterinarians, trainers and dog owners about how the product has
solved their dog’s barking problem and has dramatically improved
the relationship with their dog.
figure 11

8
1
8
Storage
Always remove the battery and empty the reservoir when putting
the spray device away for more than a week. Use a ballpoint pen
to depress the fill port stem and release any remaining spray. This
practice will prolong the operating life of the spray mechanism.
Important information
This system is not a toy. Please read all the operating instructions
carefully, fill the spray device only with recommended spray products,
and always store the spray device away from children’s reach.
Caution The spray device should only be used on healthy dogs. If
your dog has anxiety-based behavior or health problems, we suggest
that you consult a veterinarian before using this training system.

9
Troubleshooting
Problem
The anti-bark device doesn’t spray
when your dog barks.
Solution
The spray reservoir is empty. Refill it.
Steady the device on a flat surface with the fill port facing up.
Turn the spray can upside down and place the nozzle in the fill port.
Using firm pressure, push down on the spray can and hold for 15
seconds. Repeat and hold for an additional 5 seconds to fully fill the
reservoir. You don’t need to worry about overfilling. Once the pres-
sure in the reservoir equals the pressure in the can, the gas will
stop flowing. If spray is escaping while you’re attempting to fill
the device, the reservoir is not filling. Increase the downward
pressure on the refill can to insure a good seal. Escaping spray
does not indicate a full reservoir.
Solution
Check the battery.
The most common reason a receiver device stops working is a dead
battery. When the battery is in and the device is ON, it’s ‘listening’
whether on your dog or not. To extend battery life, be sure to turn OFF
the device every time you remove the collar from your dog.
Because the batteries are so small, it’s easy to put them in back-
wards. Make sure the + on the battery lines up with the + in the
battery compartment.
Occasionally newly purchased batteries may have weakened or
actually expired while “on the shelf.” We recommend trying several
different batteries before concluding the battery is not the problem.

10
1
10
Problem
The anti-bark device sprays when you
blow into the microphone, but it won’t
spray when your dog barks.
Solution
Check the fit of the collar.
A strap that is fit too tightly will not allow the sound waves to be
picked up by the microphone. A strap that is fit too loosely may be
too far from your dog’s mouth to pick up the sound. Gravity should
keep the spray device centered near your dog’s Adam’s apple.
Solution
Prevent your dog’s long hair from blocking the microphone.
• Try tying a bandanna around your dog’s neck and then place the
SpraySense Collar over it.
• Clip the hair a bit shorter in the neck area.
• Use hair bands to hold hair away from the microphone.
Problem
The anti-bark device sprays when your
dog is not barking.
Solution
Remove all other collars when using the anti-barkdevice.
Jangling of dog tags, chains and buckles can sometimes cause the
device to spray at inappropriate times.
Solution
Check the fit of the collar.
The collar may be fit too loosely and is picking up other sounds.