Spypoint TINY-D User manual

Digital Surveillance Camera
Système de surveillance photographique
Fotografisches Überwachungs system
TINY-D model / Modèle TINY-D / Modell TINY-D
User manual /Manuel de l’utilisateur /
Bedienungsanleitung
www.spypoint.com

3
English
v.1.2
English

5
English
Thank you for choosing one of our excellent
SPYPOINT products. You can now enjoy many benefits of
a full feature and easy to use digital surveillance camera.
This 8 MP digital camera was developed and designed by our
team of highly qualified engineers. It can take sharp and clean
photos or videos either day or night without using any flash.

67
English
English
FEATURES
Photo recording:
Photo resolution 8 MP
File format JPG
Time Lapse Predefined intervals from
30sec to 1h
Multi-shot Up to 6 pictures per detection
Stamp Date, time, temperature and
moon phase printed on photo
Capture mode Color by day, black and white
by night
Video recording:
Video resolution 640 x 480
File format AVI
Sequence length Adjustable from 10 to 90sec
Capture mode Color by day, black and white
by night
Memory storage: SD/SDHC card up to 32 GB
(No internal memory)
Viewing:
Built-in screen 2.4" LCD
TV output Composite video (PAL/NTSC)
Computer output USB 2.0
Power supply: (accessories sold separately, see
“Options”)
Alkaline or lithium
batteries
6x AA
Lithium battery pack Rechargeable battery pack
(LIT-09/LIT-C8)
External (12V jack) 12 volt battery (KIT-12V/
BATT-12V)
12 volt adapter (AD-12V)
Solar panel Solar panel (SP-12V)
combined with rechargeable
battery pack (LIT-09)
Detection system:
Motion sensor PIR
Main sensor's detection
angle
30°
Side sensor's detection
angle
70°
Detection range Adjustable from 5 to 50ft
Delay between each
detection
Adjustable from 1 to 30min
*Additional 10 sec. setting
(see DELAY)
Electricity option
(Connected to a 12V DC
Main source only)
Instant trigger time

89
English
English
External trigger 1/8" jack for normally open
contact
Night time illumination system:
Infrared LED (IR) 38 infrared LEDs
Exposure Automatic infrared level
adjustment
Optical field of view: 40°
KIT INCLUDES
• SPYPOINT TINY-D camera
• Installation strap
• USB Cable
• Video Cable
• User manual
REAR VIEW
OK
BUSY
1.
2.
3.
4.
5.
6.
BOTTOM VIEW
7.
10.9. 11.
13.
8.
12.
1. Power button
2. Recording indicator LED
3. “UP” button
4. “BACK” button
5. “OK” button
6. “DOWN” button
7. ALK / RECH (switch for battery)
8. SD card slot
9. USB port
10. 12 volts jack
11. External trigger jack
12. TV OUT
13. Removable battery case

10 11
English
English
POWER
The battery level is shown in the «Report» mode.
(4/4 = full, 1/4= low) When the battery level shows 2/4,
the camera will continue to take pictures but we strongly
recommend changing the batteries before they are empty.
AA batteries
This camera requires the use of 6 AA batteries (1.5V). The
use of alkaline or lithium batteries is strongly recommended.
Also note that the voltage of rechargeable AA batteries
(1.2V) is insufficient to power your SPYPOINT camera.
During the installation of alkaline batteries, place the switch
inside the battery case to “ALK” (i.e. alkaline). Insert the
batteries in the battery case as indicated and insert it inside
the camera (see figure below). Exact polarity must be
followed. We also recommend the use of new batteries to
ensure maximum performance of your camera.
ConnectorConnector
Top
Lithium battery pack
The camera SPYPOINT TINY-D can be powered by a
rechargeable lithium battery LIT-09/LIT-C-8 (sold separately,
refer to the section “OPTIONS”). This type of battery is less
affected by cold temperatures and lasts up to 3 times more
than an alkaline battery. During the installation of lithium
battery, place the switch inside the battery case to “ALK”
(i.e. alkaline). Insert the battery in the case as indicated and
insert it inside the camera (see figure below)
PINTSPY
TM
INTPSPY
ConnectorConnector
Top

12 13
English
English
TO INSERT THE BATTERY CASE INSIDE
THE CAMERA
TINY-D
PINTSPY
TM
INTPSPY
ConnectorConnector
External (12V)
The camera can be powered from an external 12 volt DC
input such as a 12 volt battery (KIT-12V/BATT-12V, sold
separately) or a 12 volt adapter (AD-12V, sold separately).
When using a 12 volt connection, we recommend you to
remove the alkaline batteries to prevent surcharges. During
the installation of 12 volt battery, place the switch inside
the battery case to “ALK” (i.e. alkaline). If combined with
a lithium battery pack, slide the switch to “RECH” (i.e.
rechargeable). To find the accessories available for the 12
volts, refer to the section “OPTIONS”.
Solar panel
This model also offers the possibility of a connection to
a solar panel SP-12V (sold separately, refer to the section
“OPTIONS”) to maintain the charge of the lithium
battery (sold separately, refer to the section “OPTIONS”)
or the 12 volt battery (sold separately, refer to the section
“OPTIONS”). During the installation of the rechargeable
lithium battery or 12 volt battery, slide the switch inside the
battery case to “RECH” (i.e. rechargeable) to activate the
charging system of the solar panel.
MEMORY CARD
Using a memory card (sold separately, refer to the section
“OPTIONS”) is required to operate the camera SPYPOINT
TINY-D. When the camera is turned on, the screen displays
“Insert memory card” in “Photo”, “Video” or “Test” mode
if no memory card is used, the camera also beeps. The SD slot
of the camera has a 32 GB memory capacity. Before inserting
or removing the memory card, the camera must be turned
off. Failing to do so may cause loss of or damage the pictures
already recorded from the memory card. When the SD card is
full, the viewing screen indicates “Disk full” when “Photo”,
“Video”or“Test” mode are selected.Thefollowingdatashows
an approximate quantity of photos or video length that can be
taken by the camera depending on the memory card capacity.

14 15
English
English
RESOLUTION 2.0 GB 4.0 GB 8.0 GB 32 GB
4 MP
6 MP
8 MP
10 MP
12 MP
1900
1580
1190
950
790
3800
3160
2380
1900
1580
7600
6320
4760
3800
3160
30400
25280
19040
15200
12640
VIDEO RESOLUTION
320 x 240
640 x 480
45 min
30 min
1h30
1h
3h
2h
12h
8h
“BUSY” LED
The “BUSY” light, located beside the LCD screen, lights up
when the camera records a file.
PROGRAMMING
Turn on the camera to navigate in the interface by pressing
“” or “” and press “OK” for selection. To modify the
selection, press “” and “” again and press “OK” to
confirm. To return to the previous menu press “”.
PHOTO
To take pictures. The “Photo” mode must be selected by
pressing “OK”; the test light in the front of the camera will
wink for 60 seconds to allow the operator to walk away from
the camera.
VIDEO
To take videos. The “Video” mode must be selected by
pressing “OK”; the test light in the front of the camera will
wink for 60 seconds to allow the operator to walk away from
the camera.
TEST
To set the camera or the distance. When “Test” mode is
selected, no picture or video is recorded. Walk perpendicularly
in front of the camera. When the camera detects movement,
the light winks to indicate that normally, a photo or video
would have been recorded. If the system does not detect
the movement, increase the distance detection using the
“Settings” menu (the option “Sensitivity” allows the user
to set the sensitivity to “High”, “Medium” or “Low”). You
can also realign the camera differently. Once you understand
how the device responds to detections, you can better adjust
the direction or the height of the camera (Recommanded
installation height: about 3 feet).
In “Test” mode, it is possible to take a picture by pressing
the “OK” button. The photo is saved and appears in
“View” mode.

16 17
English
English
SETTINGS
To define the options of the camera. To configure the
system in English, hold the button “” until “Language” is
highlighted. Press “OK”, select “English” and confirm your
choice with “OK”. The system will change all the menus in
English by itself.
Time Start /
Time Stop:
Allow the user to set the period of operation
of the camera. The start and stop time are
the hours during the camera is in action and
records pictures or videos. Example: if the
user selects a start time “7:00 am” and a stop
time “11:00 am”, the camera will only detect
for that period of time and will stay inactive
for the remaining hours. Press “OK” and use
“” or “” to adjust the hour. Press again
“OK” to set the minutes. When the time is
properly set, press “OK” once more to go
back to other settings.
For an activation of 24 hours, the same start
and stop time must be entered (example:
00:00 as start time and 00:00 as stop time.
These hours are the basic configuration of
your camera)
Note: The hours can be recorded over a
12 or 24 hours period. Refer to “Setting”/
“Time format” (00:00 means midnight)
Delay:
(10s/1m/3m/5m/
10m/15m/30m)
Select the time interval between two photos
or videos.
Additional setting: it is possible to decrease
the delay between detections to 10 seconds
(instead of 1 minute) by using the following
procedure. Note that the battery life will be
affected.
Turn OFF the camera. Press and hold the
“” button and turn the camera ON . “10sec
enabled” appears on the screen meaning
the minimum delay is now 10 seconds. If
this option is used, the 30 minute delay
disappears. To reset the camera to 1 minute
delay, follow the same procedure. “10sec
disabled” appears on the screen (see figure
below)
Multi-shot:
(1/2/3/4/5/6
consecutive shots)
Take up to 6 consecutive shots at each
detection,witha10seconddelaybetweeneach
photo. This option allows up to 6 pictures
from different angles when the camera is in
“Photo” mode.
10SEC DISABLED10SEC ENABLED
10 sec delay 1 min delay

18 19
English
English
Video length:
(10s/30s/60s/90s)
Allow the user to select the recording
duration when the camera is set in “Video”
mode.
Language:
(English/Français/
Deutsch/Italiano)
Select a language for the camera’s menu.
Sensitivity:
(High/Medium/
Low)
Allow the user to choose between three
different levels of sensitivity: “High”,
“Medium” or “Low”. The camera will only
detect sources of heat in movement. Make
sure to have the least possible objects in front
of the camera during the positioning. This
prevents picture taken by the camera when
oriented towards the sun while an object
moves in front of the camera (e.g. a branch)
Date: Set the date as Month / Day / Year
Time format:
(12h/24h)
Allow the user to choose between a 12 or
24 hours period time displays on the photos
(eg. 6:00 pm or 18:00)
Time: Set the time as Hour / Minute
Stamp:
(Yes/No)
Select or cancel imprinting date, time,
temperature and moon phases on photos.
Full moon:
New moon:
First quarter:
Last quarter:
Resolution:
(High/Medium/
Low)
Set the photo resolution.
High: 8 MP
Medium: 5 MP
Low: 3 MP
Temperature:
(°C/°F)
Select the temperature display in °F or °C.
Continuous:
(Yes/No)
Allow the user to take pictures or videos
even if the memory card is full. The camera
will continue to record photos or videos by
deleting the first files recorded.
Power:
(Batteries/
Electricity)
Allow the user to select the battery power or
the electricity power.
Choose “Electricity” if the camera is
powered of a main electric supply. (using a
12 volt DC adapterAD-12V, sold separately).
Main electric supply is recommended for
security purposes. It provides an instant
trigger time when a movement is detected.
We recommend that you remove the AA
batteries when this power supply is used.
Although, lithium battery pack can remain
safely inside the camera and it is ideal in case
of a blackout. A 12 volt DC adapter that can
provide a minimum of 800 mA is required
(See “Options” for accessories).

20 21
English
English
Note: when using the electricity power, the
“Multi-shot” mode and the “Delay” between
photos are disabled as the camera starts
instantly every time it detects motion. Also,
the imprinting temperature on each picture is
disabled.
Infrared:
(On/One LED/Off)
Allow the user to choose how many LEDs
will be turned on.
On: Every LEDs work when taking photos
or videos at night.
One LED: Only a single LED works (see
figure). This option can be useful when using
an IR-Booster/Black flash IR-Booster (sold
separately, refer to the section “OPTIONS”).
Off: LEDs are deactivated so your night
photos or videos are pitched black.
TINY-D
LED for
infrared
sensor
Side Sensors:
(On/Off)
When the side sensors are activated, a total
of 7 zones is covered. The central sensor
covers 5 zones. The side detectors are mainly
used to prepare the camera so when your
target passes through the central sensor, the
system is already pre triggered, increasing
greatly the reaction time of your camera.
Note: The side sensors require more battery
power.
26’
(8m)
30’
(9m)
50’
(15m)
30° 70°40°
6
&
6
Camera
Detection distance
(central)
Detection angles
Detection distance
of the side sensors
s: side sensors
c: central sensor
Viewing angle

22 23
English
English
Time Lapse:
(Off/30s/1m/3m/
5m/15m/30m/1h)
Allow the user to set the frequency at which time
the camera takes a picture, without detection.
For example, if the option “5 minutes” is
selected in the “Time Lapse” mode, the camera
takes a picture every 5 minutes during that
period of operation (time start and time stop)
even if there is no detection.
This option allows the user to obtain
pictures of game outside the detection range
of the camera.
Note: The “Time Lapse” mode only applies
in “PHOTO” mode, not in “VIDEO” mode.
When “Time Lapse” mode is selected, the
“Delay” mode and the “Multi-shot” mode
are disabled. In addition, the photo resolution
is reduced to 800 x 600 to allow the
possibility of video editing.
REPORT
The report mode keeps a record of the last period of use of
the camera. The beginning date corresponds with the moment
the camera is set to either “Photo” or “Video” mode. Thus,
the report is reset when changing modes.
1.
2.
3.
4.
5.
6.
7.
8.
9.
1. Beginning and end date of the report
2. Number of photos or videos taken during the day
3. Number of photos or videos taken at night
4. Total of photos or videos taken
5. Current time of the camera
6. Current date of the camera
7. Battery level (1/4 = low, 4/4 = full)
8. Remaining space on the SD card estimated by a number
of photos
9. Used space on the SD card (total number of files, only
includes photos and videos taken by a SPYPOINT camera)

24 25
English
English
EXTERNAL TRIGGERING
Input which triggers the taking of photos or videos using a
normally open contact. (Example: using a magnetic door
switch connected to an alarm system).
DOWNLOAD TO A COMPUTER
To transfer or view photos and videos on a PC, you must first
turn off the camera and connect the USB cable (supplied)
from the camera to your computer. The computer will
recognize the camera and will install the software itself.
Click on “My Computer” and select “Removable Disk”.
Then click “DCIM” and “100DSCIM” to find all your photos
and videos.
Taking the SD card out of the camera and inserting it into
the computer port will achieve the same results. If no SD
slot is built into the computer, a multi-card reader RD25-1
(sold separately, refer to the section “OPTIONS”).
VIEW
To view recorded photos or videos on TFT 2.4" viewing
camera screen or on a TV set at home.
• Viewing with the 2.4" screen: When camera is set to
“VIEW”, the last recorded photo or video recorded appears
on the screen automatically. Press “” or “” to view next or
previous images.
Press “OK” to view the different options available in
“VIEW” mode.
View Date/Time: To increase the view of the date and time
imprinted on the picture.
Protect: To protect the photo or video on the
screen.
Erase one: To erase the photo or the video on the
screen.
Format: To format memory card and to erase all
protected photos and videos.
Erase All: To erase all stored photos and videos,
with the exception of protected photos
and videos.
Exit: To return to viewing screen.
• Watching on TV: You can view the photos or videos
directly from TV. Connect the yellow end of the cable
supplied into the “VIDEO IN” of the TV and the other end
into the “TV OUT” of the camera. The last photo or video
recorded appears on the screen automatically. Press “” or
“” to view next or previous images. The options are the
same as when viewing on the 2.4" screen (see above).

26 27
English
English
TROUBLESHOOTING
No person / animal on photos
1. Rising sun or sunset can trigger sensor. Camera must be
reoriented.
2. At night, motion detector may detect beyond range of
the IR illumination. Reduce the distance setting of the
camera (“Settings” / “Sensitivity”).
3. Small animal may be triggering unit. Reduce the distance
setting and/or raise height of camera.
4. Motion detector may sense animals through foliage.
5. If person/animal moves quickly, it may move out of
the camera’s field of view before photo is taken. Move
camera further back or redirect camera.
6. Camera must be set on a stable and immovable object
e.g. large tree.
Red light in front of camera that winks
Camera is set in “Photo” or “Video” mode. Red light on the
front of the camera flashes for 60 seconds to allow the user to
leave without being photographed or filmed.
USB EXT
TV OUT
OPTIONS
See your local dealer or visit www.spypoint.com to find
available products. The following items are popular options
that can be added to a SPYPOINT camera model TINY-D.
SD Memory card, SD-4GB
Allow the user to record photos and videos.
Multi-card reader RD25-1
Allow the user to download your photos and
videos directly into a personal computer,
without using the SPYPOINT camera.
This reader works with 25 different types
of memory cards and is compatible with
SD card.
Picture viewer, PV-2.4
Digital camera. Picture viewer, SD card slot,
2.4" viewing screen, 2GB internal memory,
MP3, radio, headphone, leather transport
pocket, rechargeable lithium battery, charger
and USB cable included.
Photo and video viewer, PV-9
Photo and video viewer. 2.5" viewing screen.

28 29
English
English
Rechargeable lithium battery pack
including charger, LIT-C-8
Rechargeable lithium battery pack for
camera, to replace alkaline batteries. This
type of battery is less affected by cold
temperatures and lasts up to 3 times more
then alkaline batteries.
Additional lithium battery pack, LIT-09
An additional lithium battery pack is a
handy spare.
Water-Resistant battery box, KIT-12V
Water-resistant battery box. Includes a
12 volt rechargeable battery, charger,
12 feet power cable and carrying strap.
12ft power cable, PW-12FT
Spare 12 ft power cable, fits with KIT-
12V.
12 volt rechargeable battery and
charger, BATT-12V
To allow using external rechargeable
battery to power the camera.
12 volt power cable, CB-12FT
A 12 ft. cable allowing the user to
connect the camera into an external
12 volt DC power.
12 volt adapter, AD-12V
12 volt adapter for wall outlet, fits all
SPYPOINT cameras.
Solar Panel, SP-12V
Solar panel with an aluminum tripod.
It can be used to maintain the charge of
the lithium battery pack directly into the
camera. The solar panel can also be used
to recharge all type of 12 volt battery,
including the KIT-12V (sold separately).
IR-Booster, IRB-W
100 LED wireless infrared module that
allows the user to amplify the infrared
lights at night for clearer shots.
Black flash IR-Booster, IRB-W-B
100 invisible LED (completely invisible
to the naked eye) wireless infrared module
that allows the user to amplify the infrared
lights at night for clearer shots.
Secure Metal Box, SB-T
Metal Box to secure the camera against
theft. It also protects it from breakage that
can be caused by bears or other animals.

30 31
English
English
Mouting arm, MA-360
Adjustable mounting arm, compatible
with standard 1/4-20" tripod mount
screw.
Cable lock, CL-6ft
6 feet long locking cable with key used
for maximum theft protection.
LIMITED WARRANTY
SPYPOINT TINY-D designed by GG Telecom, is
covered by a one (1) year warranty on material and
workmanship starting from its original date of purchase.
The sales receipt is your proof of purchase and should
be presented if warranty service is needed.
This warranty does not cover any GG Telecom product
whichhas been subjected to misuse, neglect and accidents
or has been improperly used or maintained. Any
modification or tampering of the product will affect its
operation, performance, durability and void this warranty.
REPAIR SERVICE
Repairs for damages not covered by the warranty will be
subject to a reasonable charge. For technical assistance,
write to [email protected]. Give a description of the
problem with a phone number where you can be reached.
IMPORTANT: Under no circumstances GG Telecom will
accept returns without a Return Material Authorization
number (RMA).
WWW.SPYPOINT.COM
Note: For the latest update of the user manual, refer to our
website. The version number of this manual is on page 2.

33
Français
Français

35
Français
Merci d’avoir choisi un excellent produit
SPYPOINT. Vous pouvez maintenant bénéficier d’un appareil
de surveillance photographique complet et facile d’utilisation.
Cet appareil de 8 MP a été conçu et développé par notre
équipe d’ingénieurs hautement qualifiés et permet la prise de
photos et de vidéos de jour et de nuit sans aucun flash.

36 37
Français
Français
SPÉCIFICATIONS
Enregistrement Photo:
Résolution photo 8 MP
Format de fichier photo JPG
Option Time Lapse Intervalles prédéfinis de
30sec à 1h
Option Multi-photos Jusqu’à 6 photos par
détection
Informations imprimées
sur photo
Date, heure, température et
phase de lune
Mode de capture Couleur de jour,
noir et blanc de nuit
Enregistrement Vidéo:
Résolution vidéo 640 x 480
Format de fichier vidéo AVI
Durée des séquences Réglable de 10 à 90 sec.
Mode de capture Couleur de jour,
noir et blanc de nuit
Mémoire de stockage: Carte SD/SDHC jusqu’à 32
GO (Pas de mémoire interne)
Visionnement:
Écran intégré LCD de 2.4" (6.1 cm)
Sortie TV Vidéo Composite (PAL/NTSC)
Sortie Ordinateur USB 2.0
Alimentation: (accessoires vendus séparément, voir
section «Options disponibles»)
Piles alcalines ou au
lithium
6x AA
Bloc pile lithium Bloc pile rechargeable
(LIT-09/LIT-C8)
Externe (Prise 12V) Batterie 12 volts (KIT-12V/
BATT-12V)
/Adaptateur 12 volts (AD-
12V)
Panneau solaire Panneau solaire (SP-12V)
combiné avec bloc pile
lithium (LIT-09)
Système de détection:
Détecteur de
mouvement
PIR
Angle de détection du
détecteur central
30°
Angle de détection des
détecteurs de côté
70°
Distance de détection Réglable de 2 à 15 mètres
Délai entre chaque
détection
Réglable de 1 à 30 minutes
*Réglage additionnel
de 10 sec. (voir section
CONFIGURATION)

38 39
Français
Français
Option Électricité Délai de détection instantané
(*Branchement à une prise
électrique seulement)
Déclenchement externe Prise 1/8" pour contact sec
Système d’éclairage de nuit:
DEL infrarouges (IR) 38 DEL infrarouges
Exposition Ajustement automatique de
la puissance de l’éclairage
infrarouge
Angle de champ de
vision optique:
40°
CONTENU DE L’EMBALLAGE
• SPYPOINT Modèle TINY-D
• Courroie d'installation
• Câble USB
• Câble vidéo
• Manuel de l’utilisateur
7.
10.9. 11.
13.
8.
12.
OK
BUSY
1.
2.
3.
4.
5.
6.
VUE ARRIÈRE
VUE DU DESSOUS