SR Instruments SR Scales SR463iR-PH Series Service manual

Model SR463iR-PH, SR463iR-3PH Series In-Floor Platform Scale
Operating and Service Manual
Part No. MAN463iR-PH_200520 Page 1 of 20
SInstruments, Inc., 600 Young Street, Tonawanda, NY 14150
Tel: [phone] Fax: [phone] URL: www.srscales.com
email: [email protected]m Copyright 2020 SInstruments, Inc.
S
by S Instruments, Inc.
In-Floor Platform Scale
Operating and Service
Manual
SR463iR-PH SERIES

Model SR463iR-PH, SR463iR-3PH Series In-Floor Platform Scale
Operating and Service Manual
Part No. MAN463iR-PH_200520 Page 2 of 20
SInstruments, Inc., 600 Young Street, Tonawanda, NY 14150
Tel: [phone] Fax: [phone] URL: www.srscales.com
email: [email protected]m Copyright 2020 SInstruments, Inc.
TABLE OF CONTENTS
TABLE OF FIGURES......................................................................................................................2
PACKING CHECKLIST- SR463IR-PH (TWO SEPARATE SHIPMENTS)............................3
PACKING CHECKLIST- SR463IR-PH (SINGLE SHIPMENT)...............................................3
PACKING CHECKLIST- SR463IR-3PH (TWO SEPARATE SHIPMENTS)..........................4
PACKING CHECKLIST- SR463IR-3PH (SINGLE SHIPMENT).............................................4
PACKING CHECKLIST- SR463IR-4PH (TWO SEPARATE SHIPMENTS)..........................5
PACKING CHECKLIST- SR463IR-4PH (SINGLE SHIPMENT).............................................5
ASSEMBLY.......................................................................................................................................6
REPLACEMENT PARTS AND ACCESSORIES ......................................................................10
SYSTEM DESCRIPTION .............................................................................................................10
INTENDED USE.............................................................................................................................10
CLEANING AND DISINFECTING.............................................................................................11
STORAGE AND TRANSPORTATION ......................................................................................12
SPECIFICATIONS.........................................................................................................................12
BUTTON FUNCTIONS.................................................................................................................13
BASIC SYSTEM OPERATION....................................................................................................14
THEORY OF OPERATION .........................................................................................................15
CALIBRATION..............................................................................................................................16
TROUBLESHOOTING.................................................................................................................18
WARRANTY...................................................................................................................................19
TABLE OF FIGURES
Figure 1: Wall Box Assembly/Conduit Placement.....................................................................6
Figure 2: Conduit Placement and Installation Tabs..................................................................6
Figure 3: Conduit Hole in Scale Frame ......................................................................................6
Figure 4: Concrete Fill and Installation Tabs............................................................................7
Figure 5: Hardware Placement....................................................................................................7
Figure 6: Cable Connection Inside Frame..................................................................................7
Figure 7: Side Clearance Adjustment Bolts ...............................................................................8
Figure 8: Front Panel Assembly..................................................................................................9
Figure 9: Handrail Attached to Scale..........................................................................................9
Figure 10: Button Display............................................................................................................13
Figure 11: Calibration Tolerance Table.....................................................................................16
Figure 12: Calibration Switch Diagram .....................................................................................16

Model SR463iR-PH, SR463iR-3PH Series In-Floor Platform Scale
Operating and Service Manual
Part No. MAN463iR-PH_200520 Page 3 of 20
SInstruments, Inc., 600 Young Street, Tonawanda, NY 14150
Tel: [phone] Fax: [phone] URL: www.srscales.com
email: [email protected]m Copyright 2020 SInstruments, Inc.
PACKING CHECKLIST- SR463iR-PH (Two Separate Shipments)
In-Floor Platform Scale
PACKING CHECKLIST- SR463iR-PH (Single Shipment)
In-Floor Platform Scale

DESCRIPTION
QUANTITY
1st Shipment
WALL BOX ASSEMBLY
1 ea
PIT FRAME ASSEMBLY
1 ea
CONDUIT
1 ea
¼” LONG FLAT HEAD SCREW
4 ea
INSTALLATION INSTRUCTIONS
1 ea
2nd Shipment
CABLE ASSEMBLY
1 ea
PLATFORM ASSEMBLY 32 IN X 36 IN
1 ea
FRONT PANEL ASSEMBLY
1 ea
HANDRAIL
1 ea
¾” LONG FLAT HEAD SCREW
8 ea
½” LONG BUTTON HEAD SCREW
4 ea
STAR WASHERS
4 ea
CALIBRATION CERTIFICATE
1 ea
WARRANTY CARD
1 ea
MANUAL
1 ea

DESCRIPTION
QUANTITY
Box 1
FRONT PANEL/WALL BOX ASSEMBLY
1 ea
PLATFORM/PIT FRAME ASSEMBLY 32 IN X 36 IN
1 ea
CONDUIT
1 ea
CABLE ASSEMBLY
1 ea
HANDRAIL
1 ea
¼” LONG FLAT HEAD SCREW
4 ea
¾” LONG FLAT HEAD SCREW
8 ea
½” LONG BUTTON HEAD SCREW
4 ea
STAR WASHERS
4 ea
INSTALLATION INSTRUCTIONS
1 ea
CALIBRATION CERTIFICATE
1 ea
WARRANTY CARD
1 ea
MANUAL
1 ea

Model SR463iR-PH, SR463iR-3PH Series In-Floor Platform Scale
Operating and Service Manual
Part No. MAN463iR-PH_200520 Page 4 of 20
SInstruments, Inc., 600 Young Street, Tonawanda, NY 14150
Tel: [phone] Fax: [phone] URL: www.srscales.com
email: [email protected]m Copyright 2020 SInstruments, Inc.
PACKING CHECKLIST- SR463iR-3PH (Two Separate Shipments)
In-Floor Platform Scale
PACKING CHECKLIST- SR463iR-3PH (Single Shipment)
In-Floor Platform Scale

DESCRIPTION
QUANTITY
1st Shipment
WALL BOX ASSEMBLY
1 ea
PIT FRAME ASSEMBLY
1 ea
CONDUIT
1 ea
¼” LONG FLAT HEAD SCREW
4 ea
INSTALLATION INSTRUCTIONS
1 ea
2nd Shipment
CABLE ASSEMBLY
1 ea
PLATFORM ASSEMBLY 32 IN X 50 IN
1 ea
FRONT PANEL ASSEMBLY
1 ea
HANDRAIL
1 ea
¾” LONG FLAT HEAD SCREW
8 ea
½” LONG BUTTON HEAD SCREW
4 ea
STAR WASHERS
4 ea
CALIBRATION CERTIFICATE
1 ea
WARRANTY CARD
1 ea
MANUAL
1 ea

DESCRIPTION
QUANTITY
Box 1
FRONT PANEL/WALL BOX ASSEMBLY
1 ea
PLATFORM/PIT FRAME ASSEMBLY 32 IN X 50 IN
1 ea
CONDUIT
1 ea
CABLE ASSEMBLY
1 ea
HANDRAIL
1 ea
¼” LONG FLAT HEAD SCREW
4 ea
¾” LONG FLAT HEAD SCREW
8 ea
½” LONG BUTTON HEAD SCREW
4 ea
STAR WASHERS
4 ea
INSTALLATION INSTRUCTIONS
1 ea
CALIBRATION CERTIFICATE
1 ea
WARRANTY CARD
1 ea
MANUAL
1 ea

Model SR463iR-PH, SR463iR-3PH Series In-Floor Platform Scale
Operating and Service Manual
Part No. MAN463iR-PH_200520 Page 5 of 20
SInstruments, Inc., 600 Young Street, Tonawanda, NY 14150
Tel: [phone] Fax: [phone] URL: www.srscales.com
email: [email protected]m Copyright 2020 SInstruments, Inc.
PACKING CHECKLIST- SR463iR-4PH (Two Separate Shipments)
In-Floor Platform Scale
PACKING CHECKLIST- SR463iR-4PH (Single Shipment)

DESCRIPTION
QUANTITY
1st Shipment
WALL BOX ASSEMBLY
1 ea
PIT FRAME ASSEMBLY
1 ea
CONDUIT
1 ea
¼” LONG FLAT HEAD SCREW
4 ea
INSTALLATION INSTRUCTIONS
1 ea
2nd Shipment
CABLE ASSEMBLY
1 ea
PLATFORM ASSEMBLY 48 IN X 72 IN
1 ea
FRONT PANEL ASSEMBLY
1 ea
HANDRAIL
1 ea
¾” LONG FLAT HEAD SCREW
8 ea
½” LONG BUTTON HEAD SCREW
4 ea
STAR WASHERS
4 ea
CALIBRATION CERTIFICATE
1 ea
WARRANTY CARD
1 ea
MANUAL
1 ea

DESCRIPTION
QUANTITY
Box 1
FRONT PANEL/WALL BOX ASSEMBLY
1 ea
PLATFORM/PIT FRAME ASSEMBLY 48 IN X 72 IN
1 ea
CONDUIT
1 ea
CABLE ASSEMBLY
1 ea
HANDRAIL
1 ea
¼” LONG FLAT HEAD SCREW
4 ea
¾” LONG FLAT HEAD SCREW
8 ea
½” LONG BUTTON HEAD SCREW
4 ea
STAR WASHERS
4 ea
INSTALLATION INSTRUCTIONS
1 ea
CALIBRATION CERTIFICATE
1 ea
WARRANTY CARD
1 ea
MANUAL
1 ea

Model SR463iR-PH, SR463iR-3PH Series In-Floor Platform Scale
Operating and Service Manual
Part No. MAN463iR-PH_200520 Page 6 of 20
SInstruments, Inc., 600 Young Street, Tonawanda, NY 14150
Tel: [phone] Fax: [phone] URL: www.srscales.com
email: [email protected]m Copyright 2020 SInstruments, Inc.
ASSEMBLY
STEP 1: Unpack the scale system and check parts
against the PACKING CHECKLIST. If there are
any missing or damaged parts, please call the
Service Hotline at: 1-800-654-6360.
STEP 2: Verify that the serial number on the label of
Wall Box Display matches that on Platform Base.
STEP 3: (Figure 1) Mount Wall Box Display into
wall and run the conduit, with connector cable
inside, down through wall and into pit as shown.
STEP 4: Prepare pit area to accept the Scale
Frame. It is recommended that a properly plumbed
drain be installed in the center of pit to avoid any
water buildup that might damage scale.
STEP 5: (Figure 2) Center the Scale Frame in the
pit using the supplied installation tabs to suspend the
frame in place (see “Pit Area Installation Notes”).
Pit Area Installation Notes
This is a rectangular frame so it is
important to check the placement
specifications to make sure the conduit
connection is properly placed facing the
wall where the conduit/cable connection
is located. There are holes cut for
conduit entry in the center of two sides
of the frame so the scale can be placed
with either the long or short side against
wall (Figure 3). Run conduit/cable
through hole and into pit area.
For 32” x 36” Platforms: If using
supplied installation tabs to suspend
frame while pouring concrete, pit
perimeter dimensions cannot exceed
44”x 48”.
For 32” x 50” Platforms: If using
supplied installation tabs to suspend
frame while pouring concrete,
perimeter dimensions of pit cannot
exceed 44”x 62”.
For 48”x 72” Platforms: If using
supplied installation tabs to suspend
frame while pouring concrete, pit
perimeter dimensions cannot exceed
60”x 84”.
Figure1: Wall Box Assembly/Conduit Placement
14 3/4"
CONDUIT
2 1/2" 9 3/4"
WALL BOX
DETAIL
3 3/4"
MIN PIT DEPTH OF 3"
53"
TO
CENTER
OF
BOX
INSTALLATIONTABS
12.0
CONDUIT
MINPITDIM
REFERTO
INSTALLATION
NOTES
MINPITDIM
REFERTOINSTALLATIONNOTES
Figure 2: Conduit Placementand Installation Tabs
Figure 3: Conduit Hole in Scale Frame

Model SR463iR-PH, SR463iR-3PH Series In-Floor Platform Scale
Operating and Service Manual
Part No. MAN463iR-PH_200520 Page 7 of 20
SInstruments, Inc., 600 Young Street, Tonawanda, NY 14150
Tel: [phone] Fax: [phone] URL: www.srscales.com
email: [email protected]m Copyright 2020 SInstruments, Inc.
ASSEMBLY cont’d
STEP 6: (Figure 4) Back fill around the perimeter of the Pit
Frame Assembly with 3000PSI concrete. Trowel the concrete
level with the scale frame and existing floor. Trowel the base of
the pit level with the base of the frame with a gradient toward the
centered drain, if used. Conduit and cable should be left free so
cable can be easily connected tothe Platform Assembly.
STEP 7: (Figure 5) When the
concrete has set, remove and
discard the installation tabs and
screws. Install the four ¼” long
flat head screws into holes left by
plate removal.
Figure 4: Concrete Filland
Installation Tabs
Figure5: Hardware Placement
Figure 6: Cable Connection
Inside Frame
STEP 8: Remove the Platform
Assembly from the Base Assembly
using a 5/32” hex wrench to remove
the four (4) mounting screws and set
aside.
STEP 9: (Figure 6) Place the Platform Assembly
into the Pit Frame Assembly. The cable connection
will plug into the connector on the platform base.
Ensure extra cable does not interfere with platform
top.
Platform Deck Mounting
Screws (4)
Platform Deck
Platform Base
Pit Frame
Side Clearance
Adjustment Bolts (8)

Model SR463iR-PH, SR463iR-3PH Series In-Floor Platform Scale
Operating and Service Manual
Part No. MAN463iR-PH_200520 Page 8 of 20
SInstruments, Inc., 600 Young Street, Tonawanda, NY 14150
Tel: [phone] Fax: [phone] URL: www.srscales.com
email: [email protected]m Copyright 2020 SInstruments, Inc.
ASSEMBLY cont’d
Note: This scale is designed so that the Platform
Assembly is level with the Pit Frame Assembly. When
tiling or carpeting the platform deck, be sure to
compensate for the thickness of the material. Tiling
Tip: If tiling the floor, the use of an extra tile (or
something with the same surface height) is placed
under each of the four leveling feet of the pit frame.
This will bring the scale surface flush with the tiled
floor.
STEP 10: (Figure 7) Adjust the eight (8) Side
Clearance Adjustment Bolts, so that the Platform
Assembly is at an equal distance from all sides of the
Pit Frame Assembly. Tighten bolts to secure Platform
Assembly in place.
STEP 11: (Figure 5) Set the Platform Deck onto the
platform base and secure in place with the four (4) top
mounting screws. Allow 1/8” gap between Platform
Assembly and floor.
STEP 12: Install building ground wire and green ground wire from Display Front Plate into the
terminal lug in the wall box.
STEP 13: Connect Transducer Cable to the mating cable on the back of the Display Front Plate
STEP 14: Connect A/C power wires to the power supply wire leads.
Figure7: Side Clearance Adjustment Bolts
Side Clearance
Adjustment Bolts
ELECTRIC SHOCK HAZARD
TURN OFF POWER AT CIRCUIT
BREAKER FOR DISPLAY PRIOR TO
INSTALLING FRONT PANEL. DISPLAY
IS POWERED BY 120V A/C 60HZ.
WARNING
QUALIFIEDELECTRICIAN MUST
INSTALLDISPLAY ACCORDINGTO
LOCAL, STATE, AND NATIONAL
STANDARDS. 20A OR LESSBREAKER
IS RECOMMENDED. GROUNDFAULT
INTERRUPTERIS RECOMMENDED.

Model SR463iR-PH, SR463iR-3PH Series In-Floor Platform Scale
Operating and Service Manual
Part No. MAN463iR-PH_200520 Page 9 of 20
SInstruments, Inc., 600 Young Street, Tonawanda, NY 14150
Tel: [phone] Fax: [phone] URL: www.srscales.com
email: [email protected]m Copyright 2020 SInstruments, Inc.
ASSEMBLY cont’d
STEP 15: Install Front Panel Assembly (Figure 8) to the previously mounted Wall Box
Assembly. Use supplied star washers and screws. Ensure that the screws are securely tightened.
STEP 16: Restore power to the display.
STEP 17: Secure the handrail to the platform deck using the eight (8) included flat head
screws.
Figure8: FrontPanel Assembly
Figure 9: Handrail Attached to Scale
WARNING
HAND RAIL IS INTENDED TO
HELP STABLIZE AN
AMBULATORY PATIENT. DO
NOT USE HAND RAIL AS A
LIFTING AID OR TO ASSIST IN
SUPPORTING A PATIENT.

Model SR463iR-PH, SR463iR-3PH Series In-Floor Platform Scale
Operating and Service Manual
Part No. MAN463iR-PH_200520 Page 10 of 20
SInstruments, Inc., 600 Young Street, Tonawanda, NY 14150
Tel: [phone] Fax: [phone] URL: www.srscales.com
email: [email protected]m Copyright 2020 SInstruments, Inc.
REPLACEMENT PARTS AND ACCESSORIES
SYSTEM DESCRIPTION
The SR463iR-PH Series weight systems are precision digital scales specifically designed for
installation in the floor so the weighing surface is flush.
This scale system employs the latest in microprocessor and load cell technology to provide accurate
and repeatable weight data. Four (4) identically matched load cell transducers are strategically placed
to ensure an accurate representation of the patient’s weight regardless of weight distribution.
The SR463iR-PH Series display units use 120v AC line power that is mounted in a recessed wall box
so the display is flush with the wall (Figure 8).
The patient’s weight is displayed on a 16-character dot matrix liquid crystal display. The weight data
may be viewed in either pounds or kilograms, with a displayed resolution of 0.1 for each.
INTENDED USE
The SR463iR-PH Series is designed to be used as a stand-on scale for weighing ambulatory
patients as well as a Wheelchair / Chair / Walker scale for semi or non-ambulatory applications.
Part #
Description
SE4961-1
CABLE ASSEMBLY, 12 FT
SE4961-2
CABLE ASSEMBLY, 15 FT
MAN463IR-PH
MANUAL
SM7810
HANDRAIL, SS, 34” X 34”
SM7816
HANDRAIL, SS, 48” X 34”
FRTP211C1
PAPER, THERMAL PRINTER 58MM (15 ROLLS)