Stabila REC User manual

GB Operating instructions
Receiver REC

7
GB
We thank you for selecting our product. The STABILA REC receiver you have just
purchased is a high-quality, easy to operate portable receiver suitable for displaying
height reference data from rotation laser units. We wish you much enjoyment of your
purchase.
Main components
Mit dem Receiver REC können Laserstrahlen von Rotationslasern empfangen werden,
auch wenn sie für das menschliche Auge nicht mehr sichtbar sind.
We have endeavoured to explain the unit's handling and functioning in as clear and
comprehensible manner as possible. If, however, you still have any unanswered
questions, we should be pleased to provide advice over the telephone at any time on
the following telephone number: 0049 / 63 46 / 3 09-470
Operating instructions
1.
ON/OFF & volume selector switch: after switching on, press-
ing the button again selects the relevant volume level.
Holding the button depressed (for 2 seconds) switches the
unit off.
3
4
5
7
8
2
1
6
9
2. Beeper output:
beams the acoustic signal relative to the laser plane.
3. Laser receiver glass: protects the photocells, which lie
behind it and receive the laser beam.
4. LCD display window: visually displays the position relative
to the laser plane. Also shows the battery status and
whether the unit is switched on.
5. Clamp guide channel: for sliding in the retention clamp.
6.Fixing point: fastens the clamp in place after it has been
moved into its final (retention) position.
7. Marking groove: for marking reference heights - the upper
edge of the receiver is 2.5cm higher than the centre position
("Height OK").
8. Serial number label
9. Battery compartment door: for 2 AA (LR6) batteries. When
inserting the batteries, please ensure that the polarity is
correct, as shown on the drawing in the label inside.
Pressing the cover into the seal ensures dust and water-
tightness. Use a coin on the clip to open the door.
The ID label is inside.

8
to high on hight to deep battery display
(change necessary)
LCD display
Commissioning
Pressing the ON/OFF button switches the receiver on. The beeper sounds and all the
LCD elements are briefly displayed. The operating symbol shows that the receiver is
switched on. Pressing the ON/OFF button again switches between the different bee-
per volume levels: HIGH, LOW, SOUND OFF. Holding down the ON/OFF button for 2
seconds switches the receiver off. The unit will switch itself off automatically, when
no laser signal is received for more than 30 minutes. The photocells for receiving
the laser beam are located behind the (red) glass aperture. This must be held in the
direction of the rotation laser in order to receive the laser beam.
When a laser signal is received, the LCD display shows the position of the receiver
relative to the laser plane. On the display, the battery symbol illuminates when
approx. 1hour of operating life remains.
When a laser signal is received, the LCD display
shows the position of the receiver relative to the laser
plane. On the display, the battery symbol illuminates
when approx. 1hour of operating life remains.
Also the beeper sounds when a laser beam is recei-
ved. A rapid beep indicates "too high", an extended
beep indicates "Height OK" and a long beep indicates
" too low".
The beam height is marked on centre mark 7.
Measuring rod holder
The measuring rod holder included with the unit can be used universally for measu-
ring rods or battens up to 55mm wide. To connect the measuring rod holder onto the
receiver, simply slide the two guide rails on the clamp down into the appropriate
channels on the detector until the fixing knob engages (with an audible click). To
release the retention clamp, push the fixing knob back with your thumb and slide
the clamp upwards.
device is
operating

9
1. Fixing knob:
for securely engaging and releasing the retention clamp.
2. Guide rails:
for fastening onto the rear of the
3. Read-off reference:
the points lie at the "Height OK" position and therefore can be used for taking
precise readings from the measuring rod.
4. Fixing screw:
turning the screw fastens the measuring rod to the retention clamp and the
receiver and/or releases it.
Protecting your equipment
Do not expose your unit to extreme temperatures and temperature variations
(do not leave it in your car) and do not leave it out in the rain.
Use the original packaging or the carrying case when transporting the laser unit.
If the receiver is not being used for more than one month, please remove the
batteries.
Cleaning and maintenance
Wipe off any dirt from the casing with a soft, damp cloth. Do not use any aggressive
cleaning materials or solvents. Allow damp units to dry in the open air.
Unauthorised use
- Operation without instruction
- Use for other than the stated purpose
- Opening the receiver, except for the battery compartment.
- Any alteration to or conversion of the product
34
2
1

10
Reception accuracy (typical):
Display:
Protection:
Reception range:
Retention:
Beeper volume level at 20cm:
Display channels:
Receiver glass height:
Reception angle:
Marking groove:
Battery display:
Battery operating time:
Battery size:
Automatic switch-off:
Operating temperature range:
- Any person operating this receiver must have read and fully under
stood these operating instructions and, when handing over the unit,
must also ensure that they have been read and understood by the
new operator.
- Periodic calibrations or test measurements must be performed,
particularly following any abnormally severe useand before and after
important measurements.
Technical data
± 0.75 mm
LCD
dust and water-tight ( IP 67 )
up to 90m, depending on the unit.
conventional retaining clamps
high: 100+ dBA, low: 65 dBA
3
38mm
± 45°
25mm (only on the photocell side)
Yes (symbol on LCD)
100+ hours operating life
2 x AA (LR6)
after 30 minutes
-20°C to +60°C
Warnings
Stabila provides a guarantee against deficiencies and faults in the assured characte-
ristics because of material or manufacturing faults for a period of 24 months from
date of purchase. Any faults will be eliminated at Stabila's own discretion either by
repairing or replacing the unit. Stabila accepts no wider claims.
No liability is accepted for any faults due to inappropriate treatment (e.g. damage
caused by the unit falling, operation with the wrong voltage or type of current, use of
unsuitable current supply sources) or for any autonomous changes made to the unit
by the purchaser or a third party.
Also no claims under guarantee are accepted for natural wear and tear or any small
faults that do not significantly affect the unit's operation.
Any guarantee claims must be made via the dealer on the duly completed guarantee
form (see last page) to be returned with the unit.
Guarantee terms and conditions