Stafer 595.K.RS.00 Operating instructions

www.stafer.com
USER AND MAINTENANCE MANUAL:
Radio-controlled sun/wind anemometer for 1 or 2 motors ENG
595.K.RS.00
recycled paper version 2.0

üIncorrect installation can cause serious injuries.
üKeep these instructions for future maintenance operations and the disposal of the product.
üAll the product installation, connection, programming and maintenance operations must be carried out only by a qualified and skilled technician, who must
comply with laws, provisions and local regulations, and the instructions provided herein.
üWiring must comply with current CEI standards. In compliance with the provisions of Italian Ministerial Decree 37/2008, the final electrical system must be
installed only by an electrician.
üSome applications require “man present” operation and can exclude the use of radio commands or require particular safety devices.
üTo prevent potentially dangerous situations, regularly check the operating condition of the rolling shutter/awning.
01.1 SAFETY WARNINGS
01. WARNINGS. WARNING! Importanti istruzioni di sicurezza!
üRead the technical specifications in paragraph “Technical Specifications” to evaluate the operating parameters of the product.
üBefore installing the product, check compatibility with associated devices and accessories.
üThe motor connected to the device must be of the “mechanical limit switch” type, without any electronic control; the motor must be of power adequate to the
charge (check the rating plate data on the motor).
üCheck that the package is intact and has not been damaged during transport.
üA heavy shock, falls, crushing and the use of unsuitable tools can cause the damage of the external or internal parts of the product.
üDo not pierce or tamper with the product in any way. Do not modify or replace parts without the Manufacturer's permission.
üCheck that the location selected for product installation enables the blades to be exposed to the same wind to which the rolling shutter to be motorized is
exposed.
üCheck that the installation location is made of solid materials and can ensure a stable installation.
üDo not install the product near heat sources (such as chimneys, etc....).
üAdjust the control unit inclination so that blades are positioned horizontally.
üThe wind detection blades must face downward. The blades must be free to rotate without obstruction.
üCheck that the control unit is placed in a protected position from accidental impact with other objects (e.g. branches, etc.).
üThe power cable must be positioned in such a way as to avoid contact with moving parts.
üDo not use abrasive or solvent products for cleaning the device; do not clean using water-jet or high-pressure cleaners.
üFor your safety, do not work near the coiler while the motor is powered.
01.2 INSTALLATION WARNINGS
üThe product is not intended to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they are supervised or given instructions about the product way of use by a person responsible for their safety.
üCheck automation during operation and keep people at a safe distance, until operation ends.
üDo not allow children to play with the appliance or with the fixed control devices.
üDo not operate the rolling shutter when maintenance operations are being carried out (e.g. window cleaning, etc.). If the control device is automatic,
disconnect the motor from the power line.
01.3 USE WARNINGS
This sensor does not protect shutters in case of strong and sudden wind gusts. In case of weather hazards of this type, make sure that shutters
remain closed! Stafer S.p.A. declines all liability for damage incurred due to weather events not detected by the device.
Any other use beyond the field defined by Stafer S.p.A. is prohibited and involves, as well as the failure to comply with instructions provided in this guide,
voidance of Stafer S.p.A.'s liability and warranty. The installer, after the installation of the product, must train the end user about the use of the automation and
provide him with the user and maintenance manual.
WARNING!!
STAFER uses recyclable packaging materials. Dispose of materials in proper
containers, in compliance with laws in force in your location.
If you are an installer and use a large number of motors, ask your dealer about receiving
motors in “honeycomb pads”, an environmentally friendly choice that limits clutter and
waste by reducing the amount of packaging materials.
This product may have substances that are polluting for the environment
and dangerous for the health. At the end of the product life cycle, carefully
comply with local waste disposal rules. It is strictly forbidden to dispose of
the product in the domestic waste.
Let's protect the environment!
01 Warnings page 01
02 Assembly instructions page 02
03 Electrical connections page 02
04 Interfacing with home automation control units page 04
05 How to store the setting of the first remote control page 04
06 Store/delete additional remote controls page 05
07 WIND sensor page 05
08 SUN function page 06
09 Anemometric test function page 06
10 Operating logic of command buttons page 07
11 Automatic lowering function after wind alarm page 07
12 Anemometer check on awning status page 07
13 Anemometer reset to factory values page 08
14 Total reset to factory values page 08
Index
ü Power supply: 120 or 230 Vac, 50/60 Hz
ü Dimensions: 240 x 60 x H.111/133 mm
ü Weight: 230 g
ü Operating temperature: from –20 to +55 °C
ü Protecnion degree IP 55
ü Wind threshold: from 5 to 35 km/h
ü Sun threshold: from 1 to 45 Klux
Technical specifications
Dear Customer, thank you for purchasing a Stafer S.p.A. product. This guide contains information about the use of the product. Before installing and using the
product, please read this guide carefully and keep it for future reference. 595.K.RS.00 is a sun/wind sensor designed to operate tubular motors with mechanical
limit switch powered by main voltage, and suitable to operate awnings, blinds or similar products. It can be controlled by buttons only, remote control only or
both. 595.K.RS.00 allows operating the automatic retraction of awnings connected to the motor when the wind exceeds the set threshold, as well as their
release when the intensity of sun exceeds the set threshold. These thresholds are set by the factory, but they can be adjusted according to the needs.
595.K.RS.00
01
It is advisable to avoid using radio systems in areas with strong interference (for example, near police stations, airports, ports, banks, etc.).
Radio systems can be used where possible disturbances or malfunctioning of the transmitter or the receiver do not cause a risk factor, or if the risk
factor is cancelled by suitable safety systems. The presence of radio devices operating on the same transmission frequency (433.42 MHz) can
interfere with the radio receiver of the device and thus reduce the range of the system and limit the functionality of the entire system.
Notes on radio systems

02. ASSEMBLY INSTRUCTIONS
X
Components key:
(1) Impeller
(2) Anemometer body
(3) Support fastening screw
(4) Wall fastening support
(5) Rubber cable entry
02.2 FASTENING SYSTEMS
02.3 ASSEMBLY INSTRUCTIONS
02
02.1 LED DIAGRAM
Yellow
LED
Green
LED
Red
LED
Notes:
üthe product has been designed to be installed with blades facing downward. Moreover, the sensor body must be adjusted horizontally.
üthe bore interaxis is 25 mm.
ü as soon as the anemometer is powered, the three coloured LEDs will briefly flash 3 times.
Close the case by
tightening the screws.
D
Unscrew the 3
screws and open the
upper case.
A
Fasten the wall support
to the wall or ceiling
based on your needs.
E
Punch the rubber
cable entry and
insert the cable.
B
Fasten the anemometer
back into the coupling.
F
Connect the cable to the
terminals based on the
number of motors.
C
The anemometer is normally supplied already wired. If not, follow the instructions below.
03. ELECTRICAL CONNECTION
üMake all connections with the power supply disconnected.
üCheck that the power line does not feed on electrical circuits to be used for lighting.
üAlways connect the motor to the grounding system (yellow/green).
üThe power line must be equipped with a magnetothermal or differential circuit breaker. A category III overvoltage disconnection device must be
fitted on the power supply line, i.e. at a distance of at least 3.5 mm between the contacts.
üThe product does not provide for any protection against overloads or short circuits. Provide adequate protection for the load on the power supply
line, for example a fuse with a maximum value of 3.15 A (for 1 motor) or 6.3A (for 2 motors).
üThe section of the connecting cables must be proportionate to their length and to the power load absorption, and, in any case, not less than 1.5
mm.
üYou must use command buttons with spring return (“man present” type), do NOT use switches with maintained position.
üCommand buttons are connected to the main voltage, so they must be properly insulated and protected.
üOnce the electrical connections are finished, bring the motor/motors to intermediate position and check that in the “wind alarm”
condition the module controls the upward movement of the motor/motors (to exit the “wind alarm”, disconnect power for a few seconds).

03
1 MOTOR CONNECTION
2 MOTORS CONNECTION
MAIN POWER
SUPPLY
L
N
MECHANICAL
MOTOR 1
MECHANICAL
MOTOR 1
BUTTON 1
BUTTON 2
ANEMOMETER
TERMINAL BOARD
maneuver
maneuver
maneuver
blue
yellow/green
yellow/green
blue
maneuver
yellow/green
maneuver
maneuver
up
down
up
down
3.15A fuse
3.15A fuse
yellow/green
blue
MAIN POWER
SUPPLY
L
N
maneuver
maneuver
down
BUTTON 1
MECHANICAL
MOTOR 1
blue
ANEMOMETER
TERMINAL BOARD
Below is the combination of colored cables with the corresponding controls.

üThis device can be interfaced to the most widespread home automation control units through the wires of the command buttons (it is still necessary to check
beforehand the compatibility, assessing whether the home automation control unit is able to provide appropriate signals to the device).
üWarning: Before making any connections between your device and the home automation control unit you need to choose the operating logic of the buttons
that will best suit your home automation system (“pulse” or “man present” logic, see section 8 “Operating logic of command buttons”).
üIf you select the “pulse” operating logic (factory setting), the home automation control unit must be able to generate timed signals on the contacts for the
buttons (greater than 0.5 sec to start the manoeuvre, less than 0.5 sec to stop the manoeuvre). If your home automation system does not have this feature,
you must set the device to operate in “man present” logic.
üNote that the OPEN and CLOSE contacts of the home automation control unit, connected to the wires of the command buttons on the device, must close on
phase.
04. INTERFACING WITH HOME AUTOMATION CONTROL UNITS
05. HOW TO STORE ONE OR MORE REMOTE CONTROLS (OPTIONAL)
On the remote control
press STOP or UP.
G
2x
Notes:
(1): the button must be briefly pressed, approx. 1
second between two pressings.
The system can work with buttons only, with remote control only, or with both. To store the settings of one or more remote controls, proceed as follows.
OFF
ON
Switch OFF power supply
for few seconds, then
switch it ON again.
B
Move the motor to an
intermediate position
by pressing the button.
A
3 x UP
3 x DOWN
Within 15 seconds
press 3 times on
UP and 3 times on
DOWN.
C(1)
Within 15
seconds, press
UP once and
DOWN once.
E(1)
The motor completes
1 up/down movement.
D
Motor makes 2 upward
movements.
F
05.1 STORING THE FIRST REMOTE CONTROL FOR MOTOR 1
05.2 STORING REMOTE CONTROL OF MOTOR 2
04
1 x UP
1 x DOWN
Motor makes 2
upward movements.
H
(2)
Possibility to move 2 awnings independently with two
different remote controls.
A12
1 2
Possibility to move 2 awnings independently from two
separate channels of a 15-channel remote control.
B
12
01. Take the remote control already stored and working, select the associated channel
and move the awning to an intermediate position.
02. Press MENU. Display shows: - - .
Press twice on UP and 6 times on DOWN. 26 appears on the display.
03. Press STOP. The second motor performs an up/down movement..
04. In the remote control press UP or STOP, without changing channels.
05. The second motor performs 2 movements UP to confirm setting storage.
06. The second motor was automatically associated with the next channel (e.g.: if the first
motor was on channel 3, the second motor will be combined with channel 4). If the
motor movement does not correspond to the direction of the remote control button,
invert the wires of terminals 10 and 12 inside the anemometer.
Possibility to move 2 awnings simultaneously from a
single 1-channel remote control.
C1201. Take the remote control previously stored and working, and move the awning to an
intermediate position.
02. With remote control 595, press PROG. 3 times. The motor moves up/down.
Press UP twice and DOWN 6 times, then press STOP.
03. The second motor performs two movements.
04. Press UP or STOP.
05. The second motor performs 2 movements UP to confirm setting storage.
06. From this moment, the remote control will operate both motors simultaneously.
07. If the motor movement does not correspond to the direction of the remote control
button, invert the wires of terminals 10 and 12 inside the anemometer.
15 channels
1 channel
2x
Check that the motor movement corresponds to
the remote control button. Otherwise, invert the
wires of terminals 9 and 11 inside the
anemometer.
I
If a wall-mounted button does not need to be installed, it is essential to have a “flying” button to store information about the remote control (connect it as shown in
the diagram on page 3). The anemometer can be associated with a one-channel remote control, Item 595.T.X1.00, 595.M.X1.00 and Item 596.T.X1.00, or to a
multi-channel remote control Item 596.T.X5.00. In the latter case, it is necessary to initially select the desired channel to be associated with the motor. Other
remote controls, after being “copied” to the one already functioning, can control the same motor (see the instructions of the corresponding remote control). To
store the settings of the first remote control, proceed as follows.
To store settings of the second motor, the first motor must be associated with a remote control. Follow the instructions by identifying your desired system based
on your needs and devices.
01. Take the remote control previously stored and working, and move the awning to an
intermediate position.
02. With remote control 596: press MENU. Display shows: - - . Press twice on UP and 6
times on DOWN. 26 appears on the display. Press STOP.
The motor moves UP twice. With remote control 595, press PROG. 3 times. The
motor moves up/down. Press twice on UP and 6 times on DOWN, then press
STOP. The motor moves UP twice.
03. The second motor performs two movements.
04. In the second remote control, press UP or STOP.
05. The second motor performs 2 movements UP to confirm setting storage.
06. If the motor movement does not correspond to the remote control button, invert the
wires of terminals 10 and 12 inside the anemometer.

If wind speed is above the set threshold for at least 15 seconds, an upward movement is activated to protect the awning (wind alarm). During this phase, all
manual commands are disabled. The control unit exits the “wind alarm” if the wind speed keeps below the set threshold for at least 5 minutes. The wind
threshold ranges from 5 km/h to 35 km/h. The factory sets the wind threshold at level 2. If two motors are coupled with the anemometer, it is sufficient to operate
a motor only, either by button or remote control, and the settings will be valid also for the second motor.
07. WIND SENSOR
It is possible to exit the “wind alarm” mode without waiting for the 5 minutes required for the wind to go below the threshold, removing voltage from the device
and waiting a few seconds before switching on again.
07.3 FORCED EXIT FROM THE WIND ALARM
07.2 VISUAL LED SIGNALS ASSOCIATED WITH THE WIND SENSOR
05
RED LED flashing: anemometer in wind alarm mode.
RED + YELLOW LED flashing: anemometer out of order following the “anemometric test” (see paragraph 9)
07.1 CHANGE OF WIND THRESHOLD BY USING A REMOTE CONTROL OR A WALL-MOUNTED BUTTON
01. In the case of multichannel, select the correct radio channel and
move the motor to an intermediate position.
02. Press MENU. The motor shows: up/down. Display shows: - - .
03. Press UP twice and DOWN once. 21 appears on the display.
04. Press STOP once. The motor shows: up/down.
05. Press UP once. The motor shows the current value by performing 1
to 5 movements (see Table 1).
Factory sets the value on 2.
06. Press the UP button a number of times equal to the desired value.
07. The motor performs upward movements equal to the set value.
08. Press MENU to exit (the motor does not show anything).
01. Bring the motor to the intermediate position.
02. Press 3 times on PROG. The motor shows: up/down.
03. Press UP twice and DOWN once.
04. Press STOP once. The motor shows up/down
05. Press UP once. The motor shows the current value by performing 1 to
5 movements.
(1 = 5km/h; 2 = 10km/h; 3 = 15km/h; 4 = 25km/h; 5 = 35km/h).
Factory sets the value on 2.
06. Press the UP button a number of times equal to the desired value.
07. After 2 seconds, the motor performs upward movements equal to the
set value.
08. Press PROG 3 times to exit (the motor does not show anything).
USING THE REMOTE CONTROL Item 595
USING THE REMOTE CONTROL Item 596
No. of movements Threshold
1
2
3
4
5
5 Km/h
10 Km/h
15 Km/h
25 Km/h
35 Km/h
Tab. 01 - Wind threshold
Notes:
1) The button must be briefly pressed, approx. 1 second between two pressings.
2) The button must be briefly pressed, approx. 1 second between two pressings. If you do not want to change the setting, wait 15 seconds without pressing
any button.
3) If you try to set a wind threshold higher than 5, the value is rejected and completes 4 short up/down movements.
01. Bring the motor to the intermediate position.
02. Remove and restore power.
03. Press 3 times on UP and 3 times on DOWN. The motor shows:
up/down.
04. Press UP twice and DOWN once. The motor shows: up/down.
05. Press UP once. The motor shows the current value by performing 1
to 5 movements.
(1 = 5km/h; 2 = 10km/h; 3 = 15km/h; 4 = 25km/h; 5 = 35km/h).
Factory sets the value on 2.
06. Press the UP button a number of times equal to the desired value.
07. After 2 seconds, the motor performs upward movements equal to the
set value.
08. Wait for 10 seconds. The motor exits the menu without signalling.
USING THE WALL-MOUNTED BUTTON
06. HOW TO ADD OR REMOVE A REMOTE CONTROL
After having stored one or more remote controls, it is possible to add other ones by “cloning” the functioning remote controls. It is also possible to eliminate an
already stored and functioning remote control. Proceed as follows.
01. Bring the motor to the intermediate position.
02. Press PROG of a remote control already stored, for 5 seconds. Motor makes 2 upward
movements.
03. Within 15 seconds....
to add a remote control: press STOP or UP on the remote control to be added.
to delete a remote control already stored: press DOWN.
04. 2 UP movements: device stored!!
1 DOWN movement: device deleted!!
NOTES:
point 04. “error” is displayed if the radio code does not operate in a timely manner (2 downward movements).
06.1 USING THE REMOTE CONTROL (Only if a remote control is already stored)
With Item 596 With Item 595
PROG
(5 seconds)
01. Bring the motor to the intermediate position.
02. Turn off the power, wait a few seconds, then power up again.
03. Within 15 seconds, briefly and quickly press UP 3 times and DOWN 3 times. Motor
makes 3 upward movements.
04. Within 15 seconds, briefly and quickly press UP once and DOWN once.
Motor makes 2 upward movements.
05. Within 15 seconds....
to add a remote control: press STOP or UP on the remote control to be added.
To delete a remote control: press DOWN on the remote control to be deleted.
06. 2 UP movements: device stored!!
1 DOWN movement: device deleted!!
06.2 USING THE COMMAND BUTTONS
3 x UP
3 x DOWN
ON
NOTES:
point 04. “error” is displayed if the radio code does not operate in a timely manner (2 downward movements).
1 x UP
1 x DOWN

08.2 ADJUSTMENT OF “SUN” THRESHOLD WITH REMOTE CONTROL OR WALL-MOUNTED BUTTON
06
08.3 VISUAL LED SIGNALS ASSOCIATED WITH THE WIND SENSOR
YELLOW LED on steady: the sun function is active.
YELLOW LED off: the sun function is not active.
RED + YELLOW LED flashing: anemometer out of order following the “anemometer test” (see paragraph 9)
The device is provided with a diagnosis function of the wind sensor. If, for about 24 hours the wind sensor does not generate any valid pulse, the sensor
commands an upward manoeuvre of the awning in strokes, suspends all other activities and indicates the fault by flashing the LEDs. The device will come out of
this state resuming normal activities only when the anemometer generates a valid pulse. To exit the alarm, remove and restore power. The function cannot be
deactivated.
09. ANEMOMETRIC TEST FUNCTION
08.1 ACTIVATION/DEACTIVATION OF “SUN” FUNCTION WITH REMOTE CONTROL OR WALL-MOUNTED BUTTON
01. Bring the motor to the intermediate position.
02. Press 3 times on PROG. The motor shows: up/down.
03. Press twice on UP and twice on DOWN.
04. Press STOP once. The motor shows: up/down.
05. To activate, press UP once. To deactivate, press DOWN once.
06. After 2 seconds the motor replicates UP or DOWN based upon the
settings.
07. Press PROG 3 times to exit (the motor does not show anything).
USING THE REMOTE CONTROL Item 595
USING THE REMOTE CONTROL Item 596
01. Bring the motor to the intermediate position.
02. Remove and restore power.
03. Press UP 3 times and DOWN 3 times*. The motor shows: up/down.
04: Press twice on UP and twice on DOWN. The motor shows:
up/down.
05. To activate, press UP once. To deactivate, press DOWN once.
06. After 2 seconds the motor moves UP or DOWN based upon the
settings.
07. Wait for 10 seconds. The motor exits the menu without signalling.
USING THE WALL-MOUNTED BUTTON
Press the SUN button until the status of the
YELLOW LED changes (about 2 seconds)
Select the channel associated with the motor
(excluding “SE” sequencer channel)
YELLOW LED LIGHT ON/OFF:
“sun” function active/off
01. Select the correct radio channel and bring the motor on the
intermediate position.
02. Press MENU. The motor shows: up/down. Display shows: - - .
03. Press twice on UP and 3 times on DOWN. 23 appears on the display.
04. Press STOP once. The motor shows: up/down.
05. Press UP once. The motor shows the current value by performing 1
to 5 movements (see Table 2).
Factory sets the value on 2.
06. Press the UP button a number of times equal to the desired value.
07. After 2 seconds, the motor performs upward movements equal to the set
value.
08. Press MENU to exit (the motor does not show anything).
USING THE REMOTE CONTROL Item 596
01. Bring the motor to the intermediate position.
02. Press 3 times on PROG.
03. Press twice on UP and 3 times on DOWN.
04. Press STOP once. The motor shows up/down
05. Press UP once. The motor shows the current value by performing 1 to
5 movements (see Table 2). Factory sets the value on 2.
06. Press the UP button a number of times equal to the desired value.
07. After 2 seconds, the motor performs upward movements equal to the
set value.
08. Press PROG 3 times to exit (the motor does not show anything).
USING THE REMOTE CONTROL Item 595
USING THE WALL-MOUNTED BUTTON
Notes:
1) The button must be briefly pressed, approx. 1 second between two pressings.
2) If you try to set a sun threshold higher than 5 pulses, the value is rejected and completes 4 short up/down movements.
No. of
movements
Tab. 02 - Sun threshold
The “sun” function allows the awning to move automatically according to sun exposure, based on brightness measured by the light sensor installed on the
anemometer. This function is deactivated by default and can be activated at a later time. If the intensity of the sun is above the set threshold for at least 2
minutes, an automatic downward manoeuvre is performed; if the intensity of the sun is below the set threshold for at least 15 minutes, an automatic upward
manoeuvre is performed. Once an automatic downward manoeuvre for the presence of the sun is performed, the next automatic manoeuvre performed by the
control unit will be an upward movement for absence of sun and so on. The user can, in any case, operate the awning, without the manual command affecting
the operating logic of the sun sensor. The sun threshold ranges from 1 to 45 Klux. The factory sets the sun threshold to level 2. In the event of a wind alarm, the
awning will be closed whether or not any sun is shining.
08. SUN FUNCTION
(*) The buttons must be pressed shortly, max 1 second between two pressures.
01. Bring the motor to the intermediate position.
02. Remove and restore power.
03. Press 3 times on UP and 3 times on DOWN. The motor shows:
up/down.
04. Press UP twice and DOWN 3 times. The motor shows: up/down.
05. Press UP once. The motor shows the current value by performing 1 to 5
movements (see Table 2). Factory sets the value on 2.
06. Press the UP button a number of times equal to the desired value.
07. After 2 seconds, the motor performs upward movements equal to the set
value.
08. Wait for 10 seconds. The motor exits the menu without signalling.
1
2
3
4
5
Very sensitive (1 Klux)
..........
..........
..........
Not very sensitive (45 Klux)
Threshold

This device provides the possibility to choose one of the following operating logics for the command buttons:
“Pulse” logic
This is the default mode from the factory. The motor moves up (down) if the relevant contact is closed on phase for at least 0.5 sec, the motor will stop if any one
of the two contacts is closed briefly (less than 0.5 sec).
“Man present” logic
The motor moves up (down) if the relevant contact is closed on phase for at least 0.5 sec, the motor stops when contact is open.
10. OPERATING LOGIC OF COMMAND BUTTONS
This device allows lowering the awning automatically after it retracted due to a wind alarm.
After 5 minutes without wind, either of two situations can occur:
- If the sun sensor was activated, it will re-open the awning based upon brightness detection.
- If the sun sensor was deactivated, the awning will be automatically re-opened only if it was open when the wind was detected (if it was already closed, it will
remain closed).
The automatic lowering function can be activated or deactivated. The factory sets it on ACTIVE mode. To change it, follow the procedure below.
11. AUTOMATIC LOWERING FUNCTION AFTER WIND ALARM
01. Bring the motor to the intermediate position.
02. Press 3 times on PROG*. The motor shows: up/down.
03. Press 4 times on DOWN.
04. Press STOP once. The motor shows the current setting.
Once UP = man present;
Once DOWN = pulse.
05. Within 5 seconds, press the UP or DOWN button according to the
function you wish to set.
06. After 2 seconds the motor replicates the command received, with an UP
or DOWN movement.
07. Press PROG 3 times to exit (the motor does not show anything).
USING THE REMOTE CONTROL Item 595
USING THE REMOTE CONTROL Item 596
01. Bring the motor to the intermediate position.
02. Remove and restore power.
03. Press UP 3 times and DOWN 3 times*. The motor shows: up/down.
04: Press 4 times on DOWN. The motor shows the current setting.
Once UP = man present;
once DOWN = pulse.
05. Within 5 seconds, press the UP or DOWN button according to the
function you wish to set.
06. After 2 seconds the motor replicates the command received, with an
UP or DOWN movement.
07. Wait for 10 seconds. The motor exits the menu without signalling.
USING THE WALL-MOUNTED BUTTON
01. Select the correct radio channel and bring the motor on the
intermediate position.
02. Press MENU. The motor shows: up/down. Display shows: - - .
03. Press 4 times on DOWN. 04 appears on the display.
04. Press STOP once. The motor shows the current setting.
Once UP = man present; once DOWN = pulse.
05. Within 5 seconds, press the UP or DOWN button according to the
function you wish to set.
06. After 2 seconds the motor replicates the command received, with an
UP or DOWN movement.
07. Press MENU to exit (the motor does not show anything).
01. Bring the motor to the intermediate position.
02. Press 3 times on PROG*. The motor shows: up/down.
03. Press twice on UP and 4 times on DOWN.
04. Press STOP once. The motor shows the current setting.
Once UP = activate; Once DOWN = deactivate.
05. Within 5 seconds, press the UP or DOWN button according to the
function you wish to set.
06. After 2 seconds the motor replicates the command received, with an
UP or DOWN movement.
07. Press PROG 3 times to exit (the motor does not show anything).
USING THE REMOTE CONTROL Item 595
USING THE REMOTE CONTROL Item 596
01. Bring the motor to the intermediate position.
02. Remove and restore power.
03. Press 3 times on UP and 3 times on DOWN. The motor shows
up/down
04: Press twice on UP and 4 times on DOWN. The motor shows the
current setting. Once UP = activate; Once DOWN = deactivate.
05. Within 5 seconds, press the UP or DOWN button according to the
function you wish to set.
06. After 2 seconds the motor replicates the command received, with an
UP or DOWN movement.
07. Wait for 10 seconds. The motor exits the menu without signalling.
USING THE WALL-MOUNTED BUTTON
01. Select the correct radio channel and bring the motor on the
intermediate position.
02. Press MENU. The motor shows: up/down. Display shows: - - .
03. Press twice on UP and 4 times on DOWN. 24 appears on the display.
04. Press STOP once. The motor shows the current setting.
Once UP = activate; Once DOWN = deactivate.
05. Within 5 seconds, press the UP or DOWN button according to the
function you wish to set.
06. After 2 seconds the motor replicates the command with an UP or DOWN
movement.
07. Press MENU to exit (the motor does not show anything).
(*) The buttons must be pressed shortly, max 1 second between two p ressures.
(*) The buttons must be pressed shortly, max 1 second between two pressures.
12. ANEMOMETER CHECK ON AWNING STATUS
01. Press 3 times on PROG*. The motor shows: up/down.
02. Press twice on UP and 5 times on DOWN.
03.Press STOP once. The motor provides information on the awning's current
status. See table 3.
04. After 5 seconds, the motor returns to its initial position.
05. Press PROG 3 times to exit (the motor does not show anything).
USING THE REMOTE CONTROL Item 595
USING THE REMOTE CONTROL Item 596
01. In the case of multichannel, select the correct radio channel.
02. Press MENU. The motor shows: up/down. Display shows: - - .
03. Press twice on UP and 5 times on DOWN. 25 appears on the display.
04. Press STOP once. The motor provides information on the awning's
current status. See table 3.
05. After 5 seconds, the motor returns to its initial position.
06. Press MENU to exit. The motor exits the menu without signalling.
07
If the motor does not respond to the commands, it is because some alarm has been activated. To understand the type of alarm, look at the colour of the LEDs
under the anemometer. Alternatively, it is also possible to “ask” the anemometer about the alarm status. The device will order the motor to perform some
movements corresponding to the active alarm. Proceed as follows.

08
14. FACTORY VALUE RESET
The motor performs two
brief upward movements
to indicate that it was
reset.
H
All rights reserved.
STAFER S.p.a. - via Malpighi, 9 - 48018 Faenza (RA) ITALY
Tel. [phone] - Fax [phone] - www.stafer.com
All products and technical specifications given in this document are subject to variation without prior notice.
Unless previously and specifically authorised by STAFER, the device must be used exclusively with transmitters produced by STAFER.
STAFER cannot be considered responsible for damage caused by improper, incorrect or unreasonable uses.
2 x UP
8 x DOWN
3 x UP
3 x DOWN
Within 15 seconds
press 3 times on
UP and 3 times on
DOWN.
C(1)
Within 15 seconds
press twice on UP
and once on
DOWN.
E(1)
the motor performs 6
up/down movements
OFF
ON
Switch OFF power supply for
few seconds, then switch it
ON again.
B
Bring the motor to the
intermediate position.
A
The motor completes
1 up/down movement.
D F
When the anemometer is reset, all settings will return to factory values. Remote controls will be deleted.
2 x UP
Within 5 seconds,
press UP twice
G(1)
Notes: (1) Button must be pressed shortly, approx. 1 second between two pressures.
13. ANEMOMETER RESET TO FACTORY VALUES
When the anemometer is reset, all settings will return to factory values. All associated remote controls will continue to remain stored.
01. Bring the motor to the intermediate position.
02. Press 3 times on PROG*. The motor shows: up/down.
03. Press twice on UP and 8 times on DOWN.
04. Press STOP once. The motor performs 6 up/down movements.
05. Press UP.
06. The motor shows: up/down.
07. Press PROG 3 times to exit (the motor does not show anything).
USING THE REMOTE CONTROL Item 595
USING THE REMOTE CONTROL Item 596
01. Bring the motor to the intermediate position.
02. Remove and restore power.
03. Press UP 3 times and DOWN 3 times*. The motor shows up/down
04: Press twice on UP and 4 times on DOWN. The motor shows the
current setting. Once UP = activate; Once DOWN = deactivate.
05. Within 5 seconds, press the UP or DOWN button according to the
function you wish to set.
06. After 2 seconds the motor replicates the command received, with an
UP or DOWN movement.
07. Wait for 10 seconds. The motor exits the menu without signalling.
USING THE WALL-MOUNTED BUTTON
01. Select the correct radio channel and bring the motor on the
intermediate position.
02. Press MENU. The motor shows: up/down. Display shows: - - .
03. Press twice on UP and 8 times on DOWN. 28 appears on the display.
04. Press STOP once. The motor performs 6 up/down movements.
05. Press UP.
06. The motor shows: up/down.
07. Press MENU to exit (the motor does not show anything).
(*) The buttons must be pressed shortly, max 1 second between two pressures.
01. Remove and restore power.
02. Press UP 3 times and DOWN 3 times*. The motor shows:
up/down.
03. Press twice on UP and 5 times on DOWN. After 2 seconds, the
motor provides information on the awning's current status. See
table 3.
04. After 5 seconds, the motor returns to its initial position.
05. Wait for 10 seconds. The motor exits the menu without signalling.
USING THE WALL-MOUNTED BUTTON
No. of
movements Alarm
2 lowering
3 x up
4 lowering
wind alarm
sun active
stopped due
to radio test
Tab. 03 - Alarm status
Awning
position
Closed
Open
Closed
5 lowering
stopped due to
anemometric
test
Closed
(*) The buttons must be pressed shortly, max 1 second between two pressures.