Stairmaster ClubStride 5100-LE User manual

40735 REV A 1 of 6
Elliptical Unpacking and Installation Instructions
Use these instructions for the following Ellipticals:
• ClubStride® 5100-LE
•
Receiving
When the carrier delivers your order, verify that the number of items received equals the number listed on
the freight bill or express receipt.
Inspect the containers for damage. Itemize discrepancies and damage on the waybill and have the agent
sign it. Failure to describe external evidence of loss adequately may result in the carrier refusing to honor
your claim. Do not discard the packing materials until you have veried physical condition and proper
operation.
Installation Notice
The elliptical must be installed correctly before being used. StairMaster® recommends that you contact
your elliptical dealer or sales representative when your equipment arrives. The representative will help
unpack, install, and demonstrate it, to ensure that:
• Equipment is free from shipping damage
• Installation and operation are in accordance with StairMaster® standards.
Incorrect installation by unauthorized personnel can lead to equipment damage and may void the warranty.
Hardware Included:
• (4) Screw, 3/8” -16 X ”, Hex Head
• (4) Washer, 3/8” Split Lock
• (4) Washer, 3/8” Flat
• (18) Screw, #10-32 X ”, Pan Head W/Lock Washer
• (4) Washer, Plastic, 1 ” I.D. X 2 ” O.D.
• (2) Screw, ”-13 X 4”, Hex Head
• (4) Washer, ” Flat
• (2) Nut, ” – 13, Self Locking

40735 REV A 2 of 6
Components Included:
• (1) Bottom Front Left Cover
• (1) Bottom Front Right Cover
• (2) Bottom Pivot Cover #1
• (2) Bottom Pivot Cover #2
• (2) Bottom Swing Arm Shaft
Tools Required
• Shears or razor knife
• 9/16” Hex Socket Wrench
• ” Hex Socket Wrench
• 3/8” Hex Socket Wrench
• #2 Phillips Screw Driver
Unpacking the Elliptical
1. Inspect the containers for damage. Itemize discrepancies and damage on the waybill and have the agent
sign it. Failure to describe external evidence of loss or damage adequately may result in the carrier
refusing to honor your claim.
2. Use a razor knife to cut the straps that secure the elliptical cover to the pallet. Remove the cover.
3. Remove the packing materials from the elliptical.
4. Remove the parts box.
5. Unpack the Bottom Front Cover; Front Pivot Covers, and hardware from the box.
6. Use a razor knife to cut the straps that secure the Elliptical to the pallet.
7. Use a 3/8” socket wrench to remove the two lag bolts at the rear of the pallet that hold the Elliptical to
the pallet.
8. Remove packaging material from Elliptical Mast assembly.

40735 REV A 3 of 6
9. Rotate the Elliptical mast into the proper position, taking care not to pinch the electrical cable at the
bottom in the process. (See Figure 1).
10. Connect the electrical cable coming out of the bottom of the mast assembly to the electrical cable
coming out of the front of the front center tube. (See Figure 1)
11. Install and tighten (4) 3/8”-16 hex head screws, (4) 3/8” at washers, and (4) 3/8” lock washers, into
front bottom ange of the upright and the front ange of the elliptical main tube. Take care not to pinch
the electrical cable during this process. This will require a 9/16” hex socket wrench (See Figure 1).
4X 3/8"-16 HEX
HEAD SCREWS
4X 3/8" FLAT
WASHER
4X 3/8" LOCK
WASHER
FRONT BOTTOM
FLANGE (UPRIGHT)
FRONT FLANGE
(MAIN FRAME)
FIGURE 1

40735 REV A 4 of 6
12. Install (1) “Bottom Swing Arm Shaft” into the front of the foot support tube.(See Figure 2).
13. Install and tighten (1) ”-13 hex head screws, (2) 1  I.D. plastic at washers, (2)  washers, and
(1) ”-13 nuts connecting the swing arm and the foot support tube, both left and right side. This will
require a ” hex socket wrench (See Figure 2).
14. Repeat step 12 and 13 for the opposite foot support tube.
FIGURE 2
1/2"-13 HEX
HEAD SCREW
2X 1/2" FLAT
WASHER
2X 1 1/2" I.D. PLASTIC
FLAT WASHER
1/2"-13
NUT
FOOT SUPPORT
TUBE
(RH SHOWN)
SWING ARM
(RH SHOWN)
SWING ARM
SHAFT

40735 REV A 5 of 6
15. Install the front bottom left and right covers and align the holes at the sides. (See Figure 3).
16. Install and tighten (10) #10-32 phillips head screws. This will require a #2 phillips head screw driver.
(See Figure 3).
FIGURE 3
10X #10-32 PHILLIPS
HEAD SCREW
FRONT BOTTOM
RIGHT COVER
FRONT BOTTOM
LEFT COVER

40735 REV A 6 of 6
17. Install the (1) Bottom Pivot Cover #1 and (1) Bottom Pivot Cover #2 and align the holes at the front
and back of the swing arm tube. (See Figure 4).
18. Install and tighten (4) #10-32 phillips head screws. This will require a #2 phillips head screw driver.
(See Figure 4).
19. Repeat step 17 and 18 for the opposite foot support tube.
20. The Elliptical can now be removed from the pallet and is ready for use.
If the Elliptical does not run smoothly, contact your StairMaster® Fitness sales representative before using
it.
Nautilus Health & Fitness Group
StairMaster® Division
10757 E. Ute
Tulsa, OK 74461
PH: 800/635-2936
FAX: [phone]
FIGURE 4
4X #10-32 PHILLIPS
HEAD SCREW
BOTTOM PIVOT
COVER #2
BOTTOM PIVOT
COVER #1