Stamina 1350 User manual

When calling for parts or
service, please specify
the following number :
Model#: 15-1350B
CAUTION:
Weight on this product should not exceed 250 lbs.
Owner's
Manual
This Product is Distributed Exclusively by
2040 N. Alliance, Springeld, MO 65803
Customer Care
1 [phone]
www.staminaproducts.com
Product May Vary Slightly From Pictured.
Exercise can present a
health risk. Consult a
physician before beginning
any exercise program with
this equipment. If you feel
faint or dizzy, immediately
discontinue use of this
equipment. Serious bodily
injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur
if all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
securely tightened prior to
each use. Follow all safety
instructions in this manual.
!WARNING
STAMINA PRODUCTS
MADE IN CHINA
© 2016 Stamina Products, Inc.
2017, 08

TABLE OF CONTENTS
Safety Instructions ...................................... 2
Before You Begin ........................................ 4
Equipment Warning, Caution & Notice Labels ... 5
Hardware Identication Chart .................... 6
Assembly Instructions ................................ 7
Set Up Instructions ................................... 11
Operational Instructions ........................... 12
Storage ....................................................... 14
Maintenance ............................................... 14
Conditioning Guidelines ........................... 15
Warm-Up and Cool-Down ......................... 16
Warranty ..................................................... 17
Product Parts Drawing .............................. 18
Parts List .................................................... 19
Notes ........................................................... 21
Fax/Mail Ordering Form ............................ 22
SAFETY INSTRUCTIONS
2
1. Save these instructions and ensure that other exercisers read this manual prior to using the Magnetic
Recumbent 1350 Bike for the rst time.
2. Read all warnings and cautions posted on the Magnetic Recumbent 1350 Bike.
3. The Magnetic Recumbent 1350 Bike should only be used after a thorough review of the Owner’s Manual.
Make sure that it is properly assembled and tightened before use.
4. We recommend that two people be available for assembly of this product.
5. Keep children away from the Magnetic Recumbent 1350 Bike. Do not allow children to use or play on the
Magnetic Recumbent 1350 Bike. Keep children and pets away from the Magnetic Recumbent 1350 Bike
when it is in use.
6. The Magnetic Recumbent 1350 Bike is not a freewheeling exercise bike; therefore, pedal speed should
be reduced in a controlled manner to prevent injury from spinning pedals.
7. It is recommended that you place this exercise equipment on an equipment mat.
8. Set up and operate the Magnetic Recumbent 1350 Bike on a solid level surface. Do not position the
Magnetic Recumbent 1350 Bike on loose rugs or uneven surfaces.
9. Make sure that adequate space is available for access to and around the Magnetic Recumbent 1350 Bike.
10. Adjust the LEVELING CAPS(40) on the Rear Stabilizer(4) so that the bike sits on the oor without rocking.
11. Before using, inspect the Magnetic Recumbent 1350 Bike for worn or loose components, and securely
tighten or replace any worn or loose components prior to use.
12. Before using, always check the Rear Frame(3) to be sure it is secure. The ADJUSTMENT KNOB(37) must
be inserted into one of the holes in the Rear Frame(3) and tightened.
13. Each user should adjust the seat per instructions on page 12.
14. Do not attempt to adjust the seat while you are on the Magnetic Recumbent 1350 Bike.
15. Consult a physician prior to commencing an exercise program and follow his/her recommendations in
developing your tness program. If at any time during exercise you feel faint, dizzy, or experience pain, stop
and consult your physician.
16. Always choose the workout which best ts your physical strength and exibility level. Know your limits and
train within them. Always use common sense when exercising.
17. Do not wear loose or dangling clothing while using the Magnetic Recumbent 1350 Bike.
18. Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or cross
training shoes that t well, provide foot support, and feature non-skid rubber soles.
19. Be careful to maintain your balance while using, mounting, dismounting, or assembling the Magnetic
Recumbent 1350 Bike, loss of balance may result in a fall and serious bodily injury.
20. The Magnetic Recumbent 1350 Bike should not be used by persons weighing over 250 pounds.
21. The Magnetic Recumbent 1350 Bike should be used by only one person at a time.
22. The Magnetic Recumbent 1350 Bike is for consumer use only. It is not for use in public or semipublic
facilities.
23. Use two people to move the Magnetic Recumbent 1350 Bike.
!WARNING Cancer and Reproductive Harm www.P65Warnings.ca.gov
Consult your physician before starting this or any exercise program. This is
especially important if you are over the age of 35, have never exercised before,
are pregnant, or su󰀨er from any health problem. This product is for home use
only. Do not use in institutional or commercial applications. Failure to follow all
warnings and instructions could result in serious injury or death.
To reduce the risk of serious injury, read the following Safety Instructions
before using the Magnetic Recumbent 1350 Bike.
!WARNING
!WARNING

NEED HELP?
CONTACT US FIRST
1 [phone]
[e-mail]
Hi! From all of us here at Stamina Products, thank you for your purchase. We
know that you have big fitness goals in mind and we are here to help you along.
Call us, email us, or send us a message on Facebook. Be sure to contact us if you
have any questions on your new product. We look forward to hearing from you!
With your body in mind,
Stamina Customer Care
To enact your extended warranty and to help us better
serve you, please go onlineand register your new product.
register.staminaproducts.com
ONLINE
[e-mail]
www.staminaproducts.com
TELEPHONE
1 [phone]
FAX
[phone]
MAIL
Stamina Products, Inc.
ATTN: Customer Care
P.O. Box 1071
Springfield, MO 65801-1071
facebook.com/StaminaProducts
facebook.com/AeroPilates
CUSTOMER CARE HOURS:
Monday-Thursday, 7:30 AM-5:00 PM, Central Time
Friday, 8:00 AM-3:00 PM, Central Time
It is quick and easy to register online, but if you’re a little old school or just need a
reason to raise that little flag on your mailbox, fill out the info on the last page of this
manual and mail it in.

BEFORE YOU BEGIN
4
Seat Cushion
Rear Stabilizer
Foam Grip
Endcap
Meter
Crank
Right Cover
Back Cushion
Leveling Cap
Seat Frames
Right Handrail
Right Pedal
Front
Stabilizer
Front Frame
Left Cover
Left Pedal
Warning Label
Tension
Knob
Adjustment Knob
Rear Frame
Leveling Cap
THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY : Wrench
Allen Wrench (6mm)
Thank you for choosing the Magnetic
Recumbent 1350 Bike. We take great pride in
producing this quality product and hope it will
provide many hours of quality exercise to make
you feel better, look better, and enjoy life to its
fullest.
It's a proven fact that a regular exercise program
can improve your physical and mental health.
Too often, our busy lifestyles limit our time and
opportunity to exercise. The Magnetic Recumbent
1350 Bike provides a convenient and simple
method to begin your journey of getting your body
in shape and achieving a happier and healthier
lifestyle.
Before reading further, please review the
drawing below and familiarize yourself with the
parts that are labeled.
Read this manual carefully before using the
Magnetic Recumbent 1350 Bike.
Although Stamina constructs its products with
the nest materials and uses the highest standards
of manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your Magnetic Recumbent
1350 Bike, please do not return the product.
Contact us FIRST!
If a part is missing or defective, please go to
staminaproducts.com under the Customer Care
section and order the part needed, or call us toll
free at 1-800-375-7520 (in the U.S.). Our Customer
Care Staff is available to assist you from 7:30
A.M. to 5:00 P.M. (Central Time) Monday through
Thursday and 8:00 A.M. to 3:00 P.M. (Central
Time) on Friday.
Be sure to have the name and model number of
the product available when you contact us.

Label is larger than actual size
This chart is provided to help identify the warning, caution, and notice labels on the Magnetic
Recumbent 1350 Bike . Please take a moment to familiarize yourself with all of the warning, caution,
and notice labels.
EQUIPMENT WARNING, CAUTION & NOTICE LABELS
WARNING LABEL(71)W1
5

Part Number and Description Qty
6
length
length
mm.
in.
INCHES
This chart is provided to help identify the fasteners used in the assembly process. Place the washers or
the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to
check the length of the bolts and screws.
NOTICE: The length of all bolts and screws, except those with flat
heads, is measured from below the head to the end of the bolt
or screw. Flat head bolts and screws are measured from the
top of the head to the end of the bolt or screw.
After unpacking the unit, open the hardware bag and make sure that you have all the following
fasteners. Some fasteners may be already attached to the parts.
MILLIMETERS
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1/2 1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6
6 8 10 12
3/16" 1/4" 5/16" 3/8" 1/2"
HARDWARE IDENTIFICATION CHART
47 Carriage Bolt (M8 x 1.25 x 65mm) 4
49 Bolt, Button Head (M10 x 1.5 x 122mm) 2
51 Bolt, Round Head (M6 x 1 x 35mm) 8
50 Bolt, Hex Head (M6 x 1 x 37mm) 4
54 Screw, Round Head (M5 x 0.8 x 15mm) 4
60 Acorn Nut (M6 x 1) 4
61 Acorn Nut (M8 x 1.25) 4
64 Arc Washer (M6) 4
65 Arc Washer (M8) 5
66 Lock Washer (M6) 4
67 Lock Washer (M8) 5
69 Washer (M10) 2
59 Nylock Nut (M10 x 1.5 x 9mm Thick) 2
48 Bolt, Button Head (M8 x 1.25 x 15mm) 1
55 Screw, Flat Head (M5 x 0.8 x 10mm) 1

STEP 1
Attach the FRONT STABILIZER(2), the short one with the ENDCAPS(36), to the front of the FRONT
FRAME(1) with CARRIAGE BOLTS(M8x1.25x65mm)(47), ARC WASHERS(M8)(65), LOCK WASHERS(M8)
(67), and ACORN NUTS(M8x1.25)(61).
STEP 2
Unscrew to remove the ADJUSTMENT KNOB(37) from the FRONT FRAME(1). Slide the REAR FRAME(3)
backward and secure with the ADJUSTMENT KNOB(37). Attach the REAR STABILIZER(4), the one with
the LEVELING CAPS(40), to the REAR FRAME(3) with CARRIAGE BOLTS(M8x1.25x65mm)(47), ARC
WASHERS(M8)(65), LOCK WASHERS(M8)(67), and ACORN NUTS(M8)(61).
NOTE: You can adjust the LEVELING CAPS(40) on the REAR STABILIZER(4) to keep the Recumbent
Bike stable.
STEP 3
Attach the LEFT and RIGHT SEAT FRAMES(5, 6) to both sides of the REAR FRAME(3) with BUTTON
HEAD BOLTS(M10x1.5x122mm)(49), WASHERS(M10)(69), and NYLOCK NUTS(M10x1.5)(59).
ASSEMBLY INSTRUCTIONS
7
Place all parts from the box in a cleared area and position them on the oor in front of you. Remove
all packing materials from your area and place them back into the box. Do not dispose of the packing
materials until assembly is completed. Read each step carefully before beginning. If you are missing
a part, please go to staminaproducts.com under the Customer Care section and order the part
needed, e-mail us at customer[email protected], or call us toll free at 1-800-375-7520 (in
the U.S.). Our Customer Care Sta󰀨 is available to assist you from 7:30 A.M. to 5:00 P.M. (Central
Time) Monday through Thursday and 8:00 A.M. to 3:00 P.M. (Central Time) on Friday.

ASSEMBLY INSTRUCTIONS
8
STEP 4
NOTE: Install the HEX BOLTS(M6x1x37mm)(50) as shown in the illustration below. This allows the head
of the bolts to t inside the hex shape holes in the SEAT FRAMES(5, 6).
Attach the RIGHT HANDRAIL(8) to the RIGHT SEAT FRAME(6) with HEX BOLTS(M6x1x37mm)(50), ARC
WASHERS(M6)(64), LOCK WASHERS(M6)(66), and ACORN NUTS(M6x1)(60). Repeat on the left side.
STEP 5
Attach the SEAT CUSHION(41) to the LEFT and RIGHT SEAT FRAMES(5, 6) with ROUND HEAD BOLTS
(M6x1x35mm)(51). Attach the BACK CUSHION(42) to the LEFT and RIGHT SEAT FRAMES(5, 6) with
ROUND HEAD BOLTS(M6x1x35mm)(51).

ASSEMBLY INSTRUCTIONS
9
Bracket
Cable End
Hook
Metal Fitting
Strap A
Strap B
A.
B.
STEP 6
Refer to illustration A. There are two straps attached inside of the METER POST(26) to assist when pulling
the SENSOR WIRE(28) and the TENSION CABLE(24) through the METER POST(26). Tie STRAP A to the
plug end of the SENSOR WIRE(28). Tie STRAP B to the BRACKET of the TENSION CABLE(24). Pull the
STRAP A from the top of the METER POST(26) until the SENSOR WIRE(28) is pulled through and extends
out of the top of the METER POST(26). Pull the STRAP B from the square hole on the side of the METER
POST(26) until the TENSION CABLE(24) extends out of the side. Insert the METER POST(26) onto the
FRONT FRAME(1) and secure with BUTTON HEAD BOLT(M8x1.25x15mm)(48), LOCK WASHERS(M8)
(67), and ARC WASHERS(M8)(65).
STEP 7
Refer to illustration B and the inset drawing. To connect the TENSION KNOB(25) to the TENSION
CABLE(24):
1. Turn the TENSION KNOB(59) counterclockwise as far as it can go, so the CABLE END extends out of
the metal tting as far as possible. Connect the CABLE END of the TENSION KNOB(25) to the HOOK on
the end of the TENSION CABLE(24).
2. Pull on the Cable of the TENSION KNOB(25) rmly so that enough cable is available to allow the METAL
FITTING to go through the slot in the top of the BRACKET.
3. Insert the METAL FITTING into the hole at the end of the slot in the BRACKET.
4. Adjust the TENSION KNOB(25) and verify that the HOOK moves when the TENSION KNOB(25) is adjusted.
5. Attach the TENSION KNOB(25) to the METER POST(26) with FLAT HEAD SCREW(M5x0.8x10mm)(55).

ASSEMBLY INSTRUCTIONS
STEP 8
NOTE: The RIGHT PEDAL(35) has Rstamped on the end of the pedal shaft. The RIGHT PEDAL(35)
has right hand threads and is tightened by turning clockwise. The LEFT PEDAL(34) has L
stamped on the end of the pedal shaft. The LEFT PEDAL(34) has left hand threads and is
tightened by turning counterclockwise.
Thread the RIGHT PEDAL(35) to the right side of the CRANK(9) as shown. Tighten the pedal securely.
The shoulder of the PEDALS(34, 35) should be in contact with the CRANK(9) when securely tightened.
Do the same to attach the LEFT PEDAL(34) to the left side of the CRANK(9).
STEP 9
Install two AA batteries into the METER(27), the batteries are not included. See page 13 for detailed
battery installation instructions. Plug the SENSOR WIRE(28) into the METER(27), and push the excess
wires back into the METER POST(26). Place the METER(27) onto the plate on the METER POST(26)
and secure with ROUND HEAD SCREWS(M5x0.8x15mm)(54).
NOTE: Be careful not to damage the wires when attaching the METER(27).
10
Shoulder
Shoulder
Shoulder

Place the Magnetic Recumbent 1350 Bike in the area where it will be used. It is recommended that the
Magnetic Recumbent 1350 Bike be placed on an equipment mat. The Magnetic Recumbent 1350
Bike is approximately 61 3/4 inches long (max.) x 27 1/2 inches wide x 36 inches tall. (These dimensions
may vary up to one inch.) An area 4 feet wide x 7 feet long is required for safe operation of the Magnetic
Recumbent 1350 Bike. Make sure that adequate space is available for access to and passage around
the Magnetic Recumbent 1350 Bike.
EQUIPMENT MAT
Please note the Rear Frame of the
Recumbent Bike is adjustable. Use the
longest size to determine the size of
the mat.
LEVELING: Adjust the LEVELING CAPS(40) on the REAR STABILIZER(4) so that the Magnetic
Recumbent 1350 Bike sits on the oor without rocking.
MOVING: The Magnetic Recumbent 1350 Bike must be lifted to be moved. Two people are required
to grasp the FRONT STABILIZER(2) and the REAR STABILIZER(4), lift and move.
FUNCTION INSPECTION:
Visually inspect the Magnetic Recumbent 1350 Bike to verify that assembly is as shown in the above
illustration. Check the function of the Magnetic Recumbent 1350 Bike by turning the crank slowly
through one complete revolution to verify that the drive train functions properly. Adjust the TENSION
KNOB(25) and verify that it functions properly and the resistance changes.
CAUTION: Locate and read the WARNING LABEL(71) on the Magnetic Recumbent 1350 Bike. Make
sure that all users read the WARNING LABEL(71) before using the product.
SET UP INSTRUCTIONS
11

SEAT ADJUSTMENT
LOAD ADJUSTMENT
CAUTION:
1. Do not attempt to adjust the seat while you are on the Magnetic Recumbent 1350 Bike.
2. Always tighten the ADJUSTMENT KNOB(37) after adjusting the seat to a new position.
1. Unscrew to remove the ADJUSTMENT KNOB(37) from the FRONT FRAME(1). Slide the REAR
FRAME(3) to adjust the seat. Lock the REAR FRAME(3) in position by inserting the pin of the
ADJUSTMENT KNOB(37) into one of the adjustment holes in the REAR FRAME(3), then tighten the
ADJUSTMENT KNOB(37) to lock the REAR FRAME(3) securely.
2. Sit on the seat and place your feet on the pedals. You should be able to move through a complete
pedal stroke without locking your knees or shifting your hips on the seat. The seat is too close to the
pedals if you have more than a slight bend in your knees at the bottom of the pedal stroke. The seat
is too far from the pedals if you have to completely straighten your knees at the bottom of the pedal
stroke.
Proper seat adjustment is important. There are adjustment holes in the REAR FRAME(3). These
adjustment holes allow users to adjust the position of the seat for e󰀩cient exercise.
To increase the load, turn the TENSION KNOB(25) clockwise. To decrease the load, turn the TENSION
KNOB(25) counterclockwise.
OPERATIONAL INSTRUCTIONS
12
CAUTION: Do not use the HANDRAIL(7, 8) to
raise or lower your full body weight.

OPERATIONAL INSTRUCTIONS
13
USING THE FITNESS METER
1. Do not mix a new battery with an old battery.
2. Use the same type of battery. Do not mix an alkaline
battery with another type of battery.
3. Rechargeable batteries are not recommended.
4. Ultimate disposal of battery should be handled
according to all state and federal laws and regulations.
5. Do not dispose of batteries in re.
NOTE:
1. Open the Battery Door on the back of the meter.
2. The meter operates with two AA batteries, the batteries are not
included. Refer to the illustration to install or replace the batteries.
HOW TO INSTALL AND REPLACE BATTERIES:
FUNCTIONS:
Pedal movement or press the button.
Automatically shuts off after four
minutes of inactivity.
POWER OFF :
POWER ON :
MODE/RESET BUTTON:
Press to select display functions, including SCAN, TIME,
SPEED, DISTANCE, and CALORIES.
Press and hold for three seconds to reset all functions to
zero.
The meter will shut o󰀨 automatically after four minutes of inactivity. All function values
will be kept. Press the button and hold it down for three seconds to reset all functions
to zero.
NOTE:
Automatically scans each function of TIME, SPEED, DISTANCE, and CALORIES in
sequence with change every four seconds. Press and release the button until "SCAN"
appears on the display.
Displays the stepping time from one second up to 99:59 minutes. After four seconds of
inactivity, the meter will automatically stop timing the workout. Restart the workout time
by moving the pedals.
Displays the current speed from zero to 999.9 miles per hour.
Displays the distance from zero to 99.99 miles.
Displays the calorie burned from zero to 999.9 Kcal.
The calorie readout is an estimate for an average user. It should be used only as a
comparison between workouts on this unit.
SCAN:
TIME:
SPEED:
DISTANCE:
CALORIES:
AA Batteries

1. To store the Magnetic Recumbent 1350 Bike, simply keep it in a clean dry place.
2. Adjust the REAR FRAME(3) and FRONT FRAME(1) to the shortest position. The Magnetic
Recumbent 1350 Bike is approximately 39 3/4 inches long x 27 1/4 inches wide x 32 1/4 inches
tall. These dimensions will vary. Please measure your Magnetic Recumbent 1350 Bike if exact
dimensions are needed.
3. Use two people to lift the Magnetic Recumbent 1350 Bike from the FRONT STABILIZER(2) and
REAR STABILIZER(4) to move.
4. To avoid damage to the electronics, remove the batteries before storing the Magnetic Recumbent
1350 Bike for one year or more.
The safety and integrity designed into the Magnetic Recumbent 1350 Bike can only be maintained
when the Magnetic Recumbent 1350 Bike is regularly examined for damage and wear. Special
attention should be given to the following:
1. Adjust the TENSION KNOB(25) and verify that it functions properly and the resistance changes.
2. Use a wrench to verify that the pedals are tightened securely. If tightening is required, remember that
the left pedal has left hand threads and is tightened by turning counterclockwise.
3. Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts.
Tighten loose nuts and bolts.
4. Verify that the WARNING LABEL(71) is in place and easy to read. Call Stamina Products immediately
at 1-800-375-7520 for a replacement WARNING LABEL(71) if it is missing or damaged.
5. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
6. Worn or damaged components shall be replaced immediately or the Magnetic Recumbent 1350
Bike removed from service until repair is made.
7. Only Stamina Products supplied components shall be used to maintain/repair the Magnetic
Recumbent 1350 Bike.
8. Keep your Magnetic Recumbent 1350 Bike clean by wiping it o󰀨 with an absorbent cloth after use.
STORAGE
MAINTENANCE
14

How you begin your exercise program depends on your physical condition. If you have been inactive for
several years or are severely overweight, start slowly and increase your workout time gradually. Increase
your workout intensity gradually by monitoring your heart rate while you exercise.
Initially you may only be able to exercise within your target zone for a few minutes; however, your aerobic
capacity will improve over the next six to eight weeks. It is important to pace yourself while you exercise
so you don't tire too quickly.
Measure your heart rate periodically during your workout by stopping the
exercise but continuing to move your legs or walk around. Place two or
three ngers on your wrist and take a six second heartbeat count. Multiply
the results by ten to nd your heart rate. For example, if your six second
heartbeat count is 14, your heart rate is 140 beats per minute. A six second
count is used because your heart rate will drop rapidly when you stop
exercising. Adjust the intensity of your exercise until your heart rate is at the
proper level.
wrist pulse
Remember to follow these essentials:
Have your doctor review your training and diet programs.
Begin your training program slowly with realistic goals that have been set by you and your physician.
Warm up before you exercise and cool down after you work out.
Take your pulse periodically during your workout and strive to stay within a range of 60% (lower
intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower intensity, and
build up to higher intensity as you become more aerobically t.
If you feel dizzy or lightheaded you should slow down or stop exercising.
To determine if you are working out at the correct intensity, use a heart rate monitor or use the table
below. For effective aerobic exercise, your heart rate should be maintained at a level between 60%
and 90% of your maximum heart rate. If just starting an exercise program, work out at the low end of
your target heart rate zone. As your aerobic capacity improves, gradually increase the intensity of your
workout by increasing your heart rate.
CONDITIONING GUIDELINES
Target Heart Rate Zone Estimated by Age*
* For cardiorespiratory training benefits, the American College of Sports Medicine recommends
working out within a heart rate range of 55% to 90% of maximum heart rate. To predict the
maximum heart rate, the following formula was used: 220 - Age = predicted maximum heart rate
20 years
25 years
30 years
35 years
40 years
45 years
50 years
55 years
60 years
65 years
70 years
Average Maximum
Heart Rate 100%
Age
110-180 beats per minute
107-175 beats per minute
105-171 beats per minute
102-166 beats per minute
99-162 beats per minute
97-157 beats per minute
94-153 beats per minute
91-148 beats per minute
88-144 beats per minute
85-139 beats per minute
83-135 beats per minute
200 beats per minute
195 beats per minute
190 beats per minute
185 beats per minute
180 beats per minute
175 beats per minute
170 beats per minute
165 beats per minute
160 beats per minute
155 beats per minute
150 beats per minute
Target Heart Rate Zone
(55%-90% of Maximum Heart Rate)
15

WARM-UP and COOL-DOWN
Warm-Up The purpose of warming up is to prepare your body for exercise and to minimize injuries.
Warm up for two to ve minutes before strength training or aerobic exercising. Perform activities that
raise your heart rate and warm the working muscles. Activities may include brisk walking, jogging,
jumping jacks, jump rope, and running in place.
Stretching Stretching while your muscles are warm after a proper warm-up and again after your
strength or aerobic training session is very important. Muscles stretch more easily at these times
because of their elevated temperature, which greatly reduces the risk of injury. Stretches should be held
for 15 to 30 seconds. Do not bounce.
Suggested Stretching Exercises
Remember to always check with your physician before starting any exercise program.
Cool-Down The purpose of cooling down is to return the body to its normal, or near normal, resting
state at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows
blood to return to the heart. Your cool-down should include the stretches listed above and should be
completed after each strength training session.
Lower Body Stretch
Place feet shoulder-width
apart and lean forward.
Keep this position for 30
seconds using the body as a
natural weight to stretch the
backs of the legs.
DO NOT BOUNCE!
When the pull on the back of
the legs lessens, gradually
try a lower position.
Floor Stretch
While sitting on the oor,
open the legs as wide as
possible. Stretch the upper
body toward the knee on the
right leg by using your arms
to pull your chest to your
thighs. Hold this stretch 10
to 30 seconds.
DO NOT BOUNCE!
Do this stretch 10 times.
Repeat the stretch with the
left leg.
Bent Over Leg Stretch
Stand with feet shoulder-
width apart and lean forward
as illustrated. Using the
arms, gently pull the upper
body towards the right leg.
Let the head hang down.
DO NOT BOUNCE!
Hold the position a minimum
of 10 seconds. Repeat
pulling the upper body to
the left leg. Do this stretch
several times slowly.
Bent Torso Pulls
While sitting on the oor,
have legs apart, one leg
straight and one knee bent.
Pull the chest down to touch
the thigh on the leg that is
bent, and twist at the waist.
Hold this position at least 10
seconds. Repeat 10 times
on each side.
16

LIMITED WARRANTY
MODEL 15-1350B
17
WARRANTY
Stamina Products, Inc. (“Stamina”) warrants to the original purchaser that this product will be free from
defects in materials and workmanship that arise under normal use, service, proper assembly and proper
operation in accordance with product warnings/instructions for a period of 90 days on the parts and one
year on the frame from the date of the original purchase from an authorized retailer. THIS WARRANTY
SHALL NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE,
ABUSE, MISUSE, ALTERATION OF ANY KIND OR TO ANY DEFECT OR CHANGE CAUSED BY
IMPROPER ASSEMBLY, REPAIR, REPLACEMENT, SUBSTITUTION OR USE WITH PARTS NOT
PROVIDED BY STAMINA. Commercial use includes use of product in athletic clubs, health clubs, spas,
gyms, and all other public or semipublic facilities whether or not the product’s use is in furtherance of a
prot making enterprise, and all other use which is not for personal purposes.
To implement this limited warranty, send a written notice stating your name, date, and place of purchase
and a brief description of the defect along with your receipt to Stamina Products, Inc. P.O. Box 1071,
Springeld Missouri, USA, 65801-1071, or email us at customer[email protected], or call us
at 1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to return the
product or part to us for free repair or replacement at our option.
NO ACTION FOR BREACH OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE
THAN ONE (1) YEAR AFTER THE DATE THE ALLEGED BREACH WAS OR SHOULD HAVE
BEEN DISCOVERED. NO ACTION FOR BREACH OF ANY IMPLIED WARRANTY (INCLUDING
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) MAY BE COMMENCED
MORE THAN ONE (1) YEAR AFTER DELIVERY OF THE PRODUCT TO THE PURCHASER. These
warranties are not transferable. IF ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE
WITH THIS LIMITED WARRANTY OR ANY IMPLIED WARRANTY, THE REMEDY OF REPAIR OR
REPLACEMENT IS THE EXCLUSIVE REMEDY. If any claim is made under this limited warranty or any
implied warranty, Stamina reserves the right to require the product to be returned for inspection, at the
purchaser’s expense, to Stamina’s premises in Springeld, Missouri. Return of the enclosed warranty
registration card is not required for warranty coverage, but is merely a way of establishing the date and
place of purchase.
Stamina SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF TIME,
INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL, SPECIAL
OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED
WARRANTY.
THIS LIMITED WARRANTY IS THE ONLY EXPRESS WARRANTY. NO ORAL OR WRITTEN
INFORMATION GIVEN BY STAMINA, ITS AGENTS OR EMPLOYEES, SHALL CREATE A WARRANTY
OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY. This warranty gives you specic legal
rights, and you may also have other legal rights which vary from state to state. ANY OTHER RIGHT
WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO THE DURATION OF THIS
WARRANTY.
The laws in some states a󰀨ect the disclaimer or limitation of implied warranties and consequential and
incidental damages. If any such law is found applicable, the foregoing disclaimers and limitations of and
on implied warranties and consequential and incidental damages shall be deemed to be modied to the
extent necessary to comply with applicable law.

PRODUCT PARTS DRAWING
18
FRONT
BACK
Strap A
Strap B

PARTS LIST
19
1 Front Frame 1
2 Front Stabilizer 1
3 Rear Frame 1
4 Rear Stabilizer 1
5 Left Seat Frame 1
6 Right Seat Frame 1
7 Left Handrail 1
8 Right Handrail 1
9 Pulley w/ Crank 1
10 Bearing Housing 2
11 Ball Bearing 2
12 Inside Bearing Collar 1
13 Outside Bearing Collar 1
14 Bearing Washer 1
15 Bearing Snap Washer 1
16 Bearing Nut 2
18 V-Ribbed Belt 1
19 Idler Arm 1
20 Idler Wheel 1
21 Idler Wheel Spacer 1
22 Tension Spring 1
23 Magnetic Unit 1
24 Tension Cable 1
25 Tension Knob 1
26 Meter Post 1
27 Meter 1
28 Sensor Wire 1
29 Magnet 1
30 Foam Pad 3
31 Left Cover 1
32 Right Cover 1
33 Cover Cap 2
34 Left Pedal 1
35 Right Pedal 1
36 Endcap (50mm) 2
37 Adjustment Knob 1
38 Bushing 1
39 Inner Bushing 1
40 Leveling Cap (50mm) 2
41 Seat Cushion 1
42 Back Cushion 1
43 Foam Grip 2
44 Round Plug (25.4mm) 2
45 Round Plug (50mm) 1
46 Square Plug (25.4mm x 25.4mm) 4
47 Carriage Bolt (M8 x 1.25 x 65mm) 4
48 Bolt, Button Head (M8 x 1.25 x 15mm) 1
PART# PART NAME QTY

PARTS LIST
20
49 Bolt, Button Head (M10 x 1.5 x 122mm) 2
50 Bolt, Hex Head (M6 x 1 x 37mm) 4
51 Bolt, Round Head (M6 x 1 x 35mm) 8
52 Bolt, Flat Head (M10 x 1.5 x 20mm) 1
53 Bolt, Flat Head (M10 x 1.5 x 35mm) 1
54 Screw, Round Head (M5 x 0.8 x 15mm) 4
55 Screw, Flat Head (M5 x 0.8 x 10mm) 1
56 Screw, Flat Head (M4 x 15mm) 2
57 Screw, Big Round Head (M5 x 15mm) 2
58 Screw, Round Head (M4 x 25mm) 5
59 Nylock Nut (M10 x 1.5 x 9mm thick) 4
60 Acorn Nut (M6 x 1) 4
61 Acorn Nut (M8 x 1.25) 4
62 Thin Nut (3/8” - 26 x 5/32” thick) 2
63 Nut (3/8” - 26 x 9/32” thick) 2
64 Arc Washer (M6) 4
65 Arc Washer (M8) 5
66 Lock Washer (M6) 4
67 Lock Washer (M8) 5
68 Large Washer (ø16.5 x ø32 x 0.5mm thick) 1
69 Washer (M10) 2
70 Screw, Round Head (M5 x 0.8 x 6mm) 1
71 Warning Label 1
72 Wrench 1
73 Allen Wrench (6mm) 1
74 Manual 1
PART# PART NAME QTY