Stamina 1350 User manual

Model#: 15-1350
STAMINA PRODUCTS
MADE IN CHINA
Product May Vary Slightly
From Pictured.
2008, 07
Exercise can present a health
risk. Consult a physician
before beginninganyexercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior to each use.
Followallsafety instructionsin
this manual.
When calling for parts or
service, please specify the
following number.
WARNING
CAUTION:
Weight on this product should not exceed 250 lbs.
2008 Stamina Products, Inc.
2040 N. Alliance, Springfield, MO 65803
Customer Service
1 [phone]
www.staminaproducts.com
This Product is Produced Exclusively by
Owner's
Manual

TABLE OF CONTENTS
Safety Instructions 2
Before You Begin 4
Equipment Warning & Notice Labels 5
Hardware Identification Chart 6
Assembly Instructions 7
Set Up Instructions 11
Operational Instructions 12
Storage 14
Maintenance 14
Conditioning Guidelines 15
Warm-Up and Cool-Down 16
Warranty 17
Product Parts Drawing 18
Parts List 19
Notes 21
Fax/Mail Ordering Form 22
Page Page
SAFETY INSTRUCTIONS
To reduce the risk of serious injury, read the following Safety Instructions before
using the Magnetic Recumbent 1350 Bike.
WARNING:
2
Before starting any exercise or conditioning program you should consult with your personal
physician to see if you require a complete physical exam.This is especially important if you
are over the age of 35, have never exercised before, are pregnant, or suffer from any
illness. READ AND FOLLOW THE SAFETY PRECAUTIONS. FAILURE TO FOLLOW
THESE INSTRUCTIONS CAN RESULT IN SERIOUS BODILY INJURY.
WARNING:
Read all warnings posted on the Magnetic Recumbent 1350 Bike.
The Magnetic Recumbent 1350 Bike should only be used after a thorough review of the Owner's Manual.
We recommend that two people be available for assembly of this product.
Keep children away from the Magnetic Recumbent 1350 Bike. Do not allow children to use or play on the
Magnetic Recumbent 1350 Bike. Keep children and pets away from the Magnetic Recumbent 1350 Bike
when it is in use.
The Magnetic Recumbent 1350 Bike is not a freewheeling exercise bike; therefore, pedal speed should be
reduced in a controlled manner to prevent injury from spinning pedals.
Make sure that the Magnetic Recumbent 1350 Bike is properly assembled and tightened before use.
It is recommended that you place this exercise equipment on an equipment mat.
SetupandoperatetheMagnetic Recumbent 1350 Bike ona solid level surface.Donot position the Magnetic
Recumbent 1350 Bike on loose rugs or uneven surfaces.
Make sure that adequate space is available for access to and around the Magnetic Recumbent 1350 Bike.
Adjust the LEVELINGCAPS on the REAR STABILIZER so that the Magnetic Recumbent 1350 Bike sits on
the floor without rocking.
Before using, inspect the Magnetic Recumbent 1350 Bike for worn or loose components, and tighten or
replace any loose or worn components prior to use.
The ADJUSTMENT KNOB(37) should be securely tightened prior to use.
Each user should adjust the seat per instructions on page 12.
Before using, always check the seat post to be sure it is secure. The adjustment knob must be inserted into
one of the holes in the seat post and tightened.
Consult a physician prior to commencing an exercise program. If, at any time during exercise, you feel faint,
dizzy, or experience pain, stop and consult your physician.
Follow your physician's recommendations in developing your own personal fitness program.
Always choose the workout which best fits your physical strength and flexibility level. Know your limits and
train within them. Always use common sense when exercising.
Do not wear loose or dangling clothing while using the Magnetic Recumbent 1350 Bike.
Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or cross
training shoes that fit well, provide foot support, and feature non-skid rubber soles.
Care should be taken in mounting or dismounting the Magnetic Recumbent 1350 Bike.
The Magnetic Recumbent 1350 Bike should not be used by persons weighing over 250 pounds.
The Magnetic Recumbent 1350 Bike should be used by only one person at a time.
The Magnetic Recumbent 1350 Bike is for consumer use only. It is not for use in public or semipublic facilities.
Use two people to move the Magnetic Recumbent 1350 Bike.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.

3
THANK YOU FOR PURCHASING THE
Magnetic Recumbent 1350 Bike
To help you get started, we have pre-assembled most of your
Magnetic Recumbent 1350 Bike at the factory with the exception
of those few parts left unassembled for shipping purposes.
Simply follow the few assembly instructions set forth in this manual.
With regular workouts, you will be getting your body into shape
and be on your way to achieving a happier and healthier lifestyle.
Should you have any questions,
please call our Customer Service Department toll-free number,
1 [phone]
Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.
Friday, 8:00 A.M. - 3:00 P.M., Central Time.
CALL US FIRST
Customer Service
1(800)375-7520
www.staminaproducts.com
TELEPHONE
CUSTOMER SERVICE
Tel: [phone]
FAX
CUSTOMER SERVICE
Fax: [phone]
MAIL
STAMINA PRODUCTS, INC.
ATTN: Customer Service
P.O. Box 1071
Springfield, MO. 65801-1071
ONLINE
CUSTOMER SERVICE
[e-mail]
www.staminaproducts.com

BEFORE YOU BEGIN
4
Seat Cushion
Rear Stabilizer
Foam Grip
Endcap
Meter
Crank
Right Cover
Back Cushion
Leveling Cap
Seat Frames
Right Handrail
Right Pedal
Front
Stabilizer
Front Frame
Left Cover
Left Pedal
THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY : Wrench
Allen Wrench (6mm)
Warning Label
Thank you for choosing the Magnetic Recumbent
1350 Bike. We take great pride in producing this
quality product and hope it will provide many hours
ofqualityexerciseto makeyoufeel better,look better,
and enjoy life to its fullest.
It's a proven fact that a regular exercise program
can improve your physical and mental health. Too
often,ourbusylifestyleslimitourtimeandopportunity
to exercise. The Magnetic Recumbent 1350 Bike
provides a convenient and simple method to begin
your assault on getting your body in shape and
achieving a happier and healthier lifestyle.
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Read this manual carefully before using the
Magnetic Recumbent 1350 Bike.
Although Stamina constructs its products with the
finest materials and uses the highest standards of
manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your Magnetic Recumbent
1350 Bike, please do notreturn theproduct. Contact
us FIRST!
If a part is missing or defective, please call us toll
free at 1-800-375-7520 (in the U.S.). Our Customer
ServiceStaffis availableto assistyou from 7:30A.M.
to5:00P.M.(CentralTime)Monday throughThursday
and 8:00A.M. to 3:00 P.M. (CentralTime) on Friday.
If you would like to contact us online, go to our
websiteatwww.staminaproducts.comand accessthe
Customer Service section.
Be sure to have the name and model number of the
product available when you contact us.
Tension
Knob
Adjustment Knob
Rear Frame
Leveling Cap

5
EQUIPMENT WARNING & NOTICE LABELS
This chart is provided to help identify the warning & notice labels on the Magnetic Recumbent 1350 Bike.
Please take a moment to familiarize yourself with all of the warning & notice labels.
Label is larger than actual size
WARNING LABEL(71)
W1

6
Part No. and Description Qty
47 Carriage Bolt (M8 x 1.25 x 65mm) 4
49 Bolt, Button Head (M10 x 1.5 x 122mm) 2
51 Bolt, Round Head (M6 x 1 x 35mm) 8
50 Bolt, Hex Head (M6 x 1 x 37mm) 4
54 Screw, Round Head (M5 x 0.8 x 15mm) 4
60 Acorn Nut (M6 x 1) 4
61 Acorn Nut (M8 x 1.25) 4
64 Arc Washer (M6) 4
65 Arc Washer (M8) 5
66 Lock Washer (M6) 4
67 Lock Washer (M8) 5
69 Washer (M10) 2
59 Nylock Nut (M10 x 1.5 x 9mm Thick) 2
48 Bolt, Button Head (M8 x 1.25 x 15mm) 1
55 Screw, Flat Head (M5 x 0.8 x 10mm) 1
HARDWARE IDENTIFICATION CHART
This chart is provided to help identify the hardware used in the assembly process. Place the washers or the
ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check the
length of the bolts and screws.
NOTICE: The length of all bolts and screws, except those with flat heads,
is measured from below the head to the end of the bolt or screw.
Flat head bolts and screws are measured from the top of the
head to the end of the bolt or screw.
mm.
in.
INCHES
MILLIMETERS
11/2021/2 31/2 41/2 51/2 61/2
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
6 8 10 12
3/16" 5/16" 1/2"3/8"1/4"
length
length
After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

7
ASSEMBLY INSTRUCTIONS
STEP 1
Attach the FRONT STABILIZER(2), the short one with the ENDCAPS(36), to the front of the FRONT
FRAME(1) with CARRIAGE BOLTS(M8x1.25x65mm)(47), ARC WASHERS(M8)(65), LOCK
WASHERS(M8)(67), and ACORN NUTS(M8x1.25)(61).
You can adjust the LEVELING CAPS(40) on the REAR STABILIZER(4) to keep the Recumbent
Bike stable.
STEP 3
Attach the LEFT and RIGHT SEAT FRAMES(5, 6) to both sides of the REAR FRAME(3) with BUTTON
HEAD BOLTS(M10x1.5x122mm)(49), WASHERS(M10)(69), and NYLOCK NUTS(M10x1.5)(59).
STEP 2
Unscrewto removethe ADJUSTMENT KNOB(37) from theFRONT FRAME(1). Slide theREAR FRAME(3)
backward and secure with the ADJUSTMENT KNOB(37). Attach the REAR STABILIZER(4), the one with
the LEVELING CAPS(40), to the REAR FRAME(3) with CARRIAGE BOLTS(M8x1.25x65mm)(47), ARC
WASHERS(M8)(65), LOCK WASHERS(M8)(67), and ACORN NUTS(M8)(61).
NOTE:
Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all
packing materials from your area and place them back into the box.Do not dispose of the packing materials
until assembly is completed. Read each step carefully before beginning. If you are missing a part please call
ourtoll-free numberforassistance1-800-375-7520 ore-mail us at: [e-mail]

ASSEMBLY INSTRUCTIONS
8
STEP 4
NOTE: Install the HEX BOLTS(M6x1x37mm)(50) as shown in the illustration above. This allows the head
of the bolts to fit inside the hex shape holes in the SEAT FRAMES(5, 6).
Attach the RIGHT HANDRAIL(8) to the RIGHT SEAT FRAME(6) with HEX BOLTS(M6x1x37mm)(50),
ARC WASHERS(M6)(64), LOCK WASHERS(M6)(66), and ACORN NUTS(M6x1)(60). Repeat on the left
side.
STEP 5
Attach the SEAT CUSHION(41) to the LEFT and RIGHT SEAT FRAMES(5, 6) with ROUND HEAD BOLTS
(M6x1x35mm)(51).
Attachthe BACK CUSHION(42) to the LEFT and RIGHT SEAT FRAMES(5, 6) with ROUND HEAD BOLTS
(M6x1x35mm)(51).

ASSEMBLY INSTRUCTIONS
Bracket
Cable End
Spring Hook
Metal Fitting
Strap A
Strap B
A. B.
STEP 6
Refer toillustrationA.Pull the endsof the TENSION CABLE(24)and SENSOR WIRE(28) outof theFRONT
FRAME(1).Thereare twostrapsattached insideofthe METER POST(26) toassistwhenpulling theSENSOR
WIRE(28) and the TENSION CABLE(24) through the METER POST(26). Tie STRAP A to the plug end of
the SENSOR WIRE(28). Tie STRAP B to the BRACKET of the TENSION CABLE(24). Pull the STRAP A
from the square hole on the top of the METER POST(26) until theSENSOR WIRE(28) is pulled throughand
extendsout of the squarehole. Pullthe STRAPB fromthe squareholeon the side of theMETER POST(26)
until the TENSION CABLE(24) extends out of the side. Insert the METER POST(26) onto the FRONT
FRAME(1) and secure with BUTTON HEAD BOLT(M8x1.25x15mm)(48), LOCKWASHERS(M8)(67), and
ARC WASHERS(M8)(65).
STEP 7
Refer to illustration B and the inset drawing.Turn the TENSION KNOB(25) counterclockwise as far as it can
go, so the CABLE END extends out of the metal fitting as far as possible. Connect the CABLE END of the
TENSION KNOB(25) into the SPRING HOOK on the end of the TENSION CABLE(24). Pull on the CABLE
END of the TENSION KNOB(25) firmly so that enough cable is available to insert the CABLE END through
theslot in theBRACKET. Then insertthe METALFITTING on the CABLE END of the TENSION KNOB(25)
into the hole at the end of the slot in the BRACKET. Adjust the TENSION KNOB(25) and verify that the
SPRING HOOK moves when the TENSION KNOB(25) is adjusted. Attach the TENSION KNOB(25) to the
METER POST(26) with FLAT HEAD SCREW(M5x0.8x10mm)(55).
9

ASSEMBLY INSTRUCTIONS
STEP 8
NOTE: The RIGHT PEDAL(35) has Rstamped on the end of the pedal shaft. The RIGHT PEDAL(35) has
right hand threads and is tightened by turning clockwise. The LEFT PEDAL(34) has Lstamped on
the end of the pedal shaft. The LEFT PEDAL(34) has left hand threads and is tightened by turning
counter clockwise.
Thread the RIGHT PEDAL(35) to the right side of the CRANK(9) as shown. Tighten the pedal securely.Do
the same to attach the LEFT PEDAL(34) to the left side of the CRANK(9).
STEP 9
InstalltwoAAbatteriesinto theMETER(27), twobatteriesincluded. See page13fordetailedbatteryinstallation
instructions. Plug the SENSOR WIRE(28) into the METER(27), and push the excess wires back into the
METER POST(26). Placethe METER(27) ontothe plateon theMETER POST(26) and securewithROUND
HEAD SCREWS(M5x0.8x15mm)(54).
NOTE: Be careful not to damage the wires when attaching the METER(27).
10

11
Locate and read the WARNING LABEL(71) on the Magnetic Recumbent 1350 Bike. Make
sure that all users read the WARNING LABEL(71).
EQUIPMENT MAT
Please note the Rear Frame of the
Recumbent Bike is adjustable. Use the
longest size to determine the size of the mat.
CAUTION:
SET UP INSTRUCTIONS
Place the Magnetic Recumbent 1350 Bike in the area where it will be used. It is recommended that the
Magnetic Recumbent 1350 Bike be placed on an equipment mat. The Magnetic Recumbent 1350 Bike
is approximately 61 3/4 inches long (max.) x 27 1/2 inches wide x 36 inches tall. (These dimensions may
vary up to one inch.) An area 4 feet wide x 7 feet long is required for safe operation of the Magnetic
Recumbent 1350 Bike. Make sure that adequate space is available for access to and passage around the
Magnetic Recumbent 1350 Bike.
FUNCTION INSPECTION:
Visually inspect the Magnetic Recumbent 1350 Bike to verify that assembly is as shown in the above
illustration. Check the function of the Magnetic Recumbent 1350 Bike by turning the crank slowly through
one complete revolution to verify that the drive train functions properly.Adjust the TENSION KNOB(25) and
verify that it functions properly.
Adjust the LEVELING CAPS(40) on the REAR STABILIZER(4) so the bike sits on the floor
without rocking. Removeandreposition the LEVELING CAPS(40) onthe REAR STABILIZER
(4) to level the Magnetic Recumbent 1350 Bike.
The Magnetic Recumbent 1350 Bike must be lifted to be moved. Two people are required to
grasp the FRONT STABILIZER(2) and the REAR STABILIZER(4), lift and move.
LEVELING:
MOVING:

OPERATIONAL INSTRUCTIONS
SEAT ADJUSTMENT
CAUTION:
1.
2.
Unscrewto removetheADJUSTMENT KNOB(37) fromthe FRONT FRAME(1). Slidethe REAR FRAME
(3) to adjust the seat. Lock the REAR FRAME(3) in position by inserting the pin of the ADJUSTMENT
KNOB(37) into one of the adjustment holes in the REAR FRAME(3), then tighten the ADJUSTMENT
KNOB(37) to lock the REAR FRAME(3) securely.
Sit on the seat and place your feet on the pedals. You should be able to move through a complete pedal
stroke without locking your knees or shifting your hips on the seat. The seat is too close to the pedals if
you have more than a slight bend in your knees at the bottom of the pedal stroke. The seat is too far from
the pedals if you have to completely straighten your knees at the bottom of the pedal stroke.
1.
2.
Do not attempt to adjust the seat while you are on the Magnetic Recumbent 1350 Bike.
Always tighten the ADJUSTMENT KNOB(37) after adjusting the seat to a new position.
12
To increase the load, turn the TENSION KNOB(25) clockwise. To decrease the load, turn the TENSION
KNOB(25) counterclockwise.
LOAD ADJUSTMENT
Proper seat adjustment is important. There are seven adjustment holes in the REAR FRAME(3). These
adjustment holes allow users to adjust the position of the seat for efficient exercise.

USING THE METER
Open the Battery Door on the back of the meter.
The meter operates with two AA batteries, two batteries included.
Refer to the illustration to install or replace the batteries.
1.
2.
Do not mix a new battery with an old battery.
Use the same type of battery. Do not mix an alkaline battery with
another type of battery.
Rechargeable batteries are not recommended.
1.
2.
3.
NOTE:
CALORIES:
13
HOW TO INSTALL AND REPLACE BATTERIES:
TIME:
Automatically scans each function of TIME, SPEED, DISTANCE, and CALORIES in
sequence with change every four seconds. Press and release the button until "SCAN"
appears on the display.
Displays the time from one second up to 99:59 minutes.
Displays the current speed from zero to 999.9 miles per hour.
Displays the distance from zero to 99.99 miles.
Displays the calorie consumption from zero to 999.9 Kcal.
The calorie readout is an estimate for an average user. It should be used only as a
comparison between workouts on this unit.
SPEED:
FUNCTIONS:
SCAN:
DISTANCE:
Pedal movement or push the button.
Automatic shut off after four minutes of
inactivity.
POWER OFF :
POWER ON :
MODE/RESET BUTTON:
Press to select display functions, include SCAN, TIME,
SPEED, DISTANCE, and CALORIES.
Press and hold for three seconds to reset all functions to
zero.
The meter will shut off automatically after four minutes of inactivity.All function values will
be kept. Push the button and hold it down for three seconds to reset all functions to zero.
NOTE:
OPERATIONAL INSTRUCTIONS
AABatteries

STORAGE
14
1.
2.
3.
4.
To store the Magnetic Recumbent 1350 Bike, simply keep it in a clean dry place.
Adjust the REAR FRAME(3) into the FRONT FRAME(1) to the shortest position. The Magnetic
Recumbent 1350 Bike is approximately 39 3/4 inches long x 27 1/4 inches wide x 32 1/4 inches tall.
These dimensions will vary. Please measure your Magnetic Recumbent 1350 Bike if exact dimensions
are needed.
Usetwo people to liftthe Magnetic Recumbent 1350 Bike from theFRONT STABILIZER(2) and REAR
STABILIZER(4) to move.
To avoid damage to the electronics, remove the batteries before storing the Magnetic Recumbent 1350
Bike for one year or more.
MAINTENANCE
The safety and integrity designed into the Magnetic Recumbent 1350 Bike can only be maintained when
the Magnetic Recumbent 1350 Bike is regularly examined for damage and wear. Special attention should
be given to the following:
Adjust the TENSION KNOB(25) and verify that the Magnetic System provides tension. The Magnetic
System should provide many years of use.
Use a wrench to verify that the pedals are tightened securely. If tightening is required, remember that the
left pedal has left hand threads and is tightened by turning counterclockwise.
Verify that the WARNING LABEL(71) is in place and easy to read. Call Stamina Products immediately at
1-800-375-7520 for a replacement WARNING LABEL(71) if it is missing or damaged.
It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
Worn or damaged components shall be replaced immediately or the Magnetic Recumbent 1350 Bike
removed from service until repair is made.
Only Stamina Productssupplied componentsshall be usedto maintain/repair the Magnetic Recumbent
1350 Bike.
Keep your Magnetic Recumbent 1350 Bike clean by wiping with an absorbent cloth after use.
1.
2.
3.
4.
5.
6.
7.

15
CONDITIONING GUIDELINES
How you begin your exercise program depends on your physical condition. If you have been inactive for
several years or are severely overweight, start slowly and increase your workout time gradually. Increase
your workout intensity gradually by monitoring your heart rate while you exercise.
Initially you may only be able to exercise within your target zone for a few minutes; however, your aerobic
capacity will improve over the next six to eight weeks. It is important to pace yourself while you exercise so
you don't tire too quickly.
Measure your heart rate periodically during your workout by stopping the
exercise but continuing to move your legs or walk around. Place two or three
fingersonyour wristandtakea sixsecond heartbeatcount.Multiplythe results
by ten to find your heart rate. For example, if your six second heartbeat count
is 14, your heart rate is 140 beats per minute. A six second count is used
because your heart rate will drop rapidly when you stop exercising.Adjust the
intensity of your exercise until your heart rate is at the proper level.
wrist pulse
Have your doctor review your training and diet programs.
Begin your training program slowly with realistic goals that have been set by you and your physician.
Warm up before you exercise and cool down after you work out.
Take your pulse periodically during your workout and strive to stay within a range of 60% (lower
intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower intensity, and
build up to higher intensity as you become more aerobically fit.
If you feel dizzy or lightheaded you should slow down or stop exercising.
Target Heart Rate Zone Estimated byAge*
Remember to follow these essentials:
To determine if you are working out at the correct intensity, use a heart rate monitor or use the table below.
For effective aerobic exercise, your heart rate should be maintained at a level between 60% and 90% of
your maximum heart rate. If just starting an exercise program, work out at the low end of your target heart
rate zone.As your aerobic capacity improves, gradually increase the intensity of your workout by increasing
your heart rate.
Forcardiorespiratorytrainingbenefits,theAmericanCollege ofSports Medicine recommendsworking
out within a heart rate range of 55% to 90% of maximum heart rate. To predict the maximum heart
rate, the following formula was used: 220 - Age = predicted maximum heart rate
*
20 years
25 years
30 years
35 years
40 years
45 years
50 years
55 years
60 years
65 years
70 years
Target Heart Rate Zone
(55%-90% of Maximum Heart Rate) Average Maximum Heart Rate 100%
Age
110-180 beats per minute
107-175 beats per minute
105-171 beats per minute
102-166 beats per minute
99-162 beats per minute
97-157 beats per minute
94-153 beats per minute
91-148 beats per minute
88-144 beats per minute
85-139 beats per minute
83-135 beats per minute
200 beats per minute
195 beats per minute
190 beats per minute
185 beats per minute
180 beats per minute
175 beats per minute
170 beats per minute
165 beats per minute
160 beats per minute
155 beats per minute
150 beats per minute

16
WARM-UP and COOL-DOWN
Warm-Up The purpose of warmingup is to prepareyour bodyforexercise andto minimize injuries.Warm
up for two to five minutes before strength training or aerobic exercising. Perform activities that raise your
heart rate and warm the working muscles.Activities may include brisk walking, jogging, jumping jacks, jump
rope, and running in place
Stretching Stretching while your muscles are warm after a proper warm-up and again after your strength
or aerobic training session is very important. Muscles stretch more easily at these times because of their
elevatedtemperature,which greatly reducestheriskof injury.Stretchesshouldbe heldfor 15to 30seconds.
Do not bounce.
Suggested Stretching Exercises
Remember to always check with your physician before starting any exercise program.
Cool-Down The purpose of cooling down is to return the body to its normal, or near normal, resting state
at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows blood to
return to the heart.Your cool-down should include the stretches listed above and should be completed after
each strength training session.
Lower Body Stretch
Place feet shoulder-width
apart and lean forward.
Keep this position for 30
seconds using the body as a
natural weight to stretch the
backs of the legs.
DONOT BOUNCE!
When the pull on the back of
the legs lessens, gradually
try a lower position.
Floor Stretch
While sitting on the floor,
open the legs as wide as
possible. Stretch the upper
body toward the knee on the
right leg by using your arms
to pull your chest to your
thighs. Hold this stretch 10
to 30 seconds.
DONOT BOUNCE!
Do this stretch 10 times.
Repeat the stretch with the
left leg.
Bent Over Leg Stretch
Stand with feet shoulder-
width apart and lean forward
as illustrated. Using the
arms, gently pull the upper
body towards the right leg.
Let the head hang down.
DONOT BOUNCE!
Hold the position a minimum
of 10 seconds. Repeat
pulling the upper body to the
left leg. Do this stretch
several times slowly.
Bent Torso Pulls
While sitting on the floor,
have legs apart, one leg
straight and one knee bent.
Pull the chest down to touch
the thigh on the leg that is
bent, and twist at the waist.
Hold this position at least 10
seconds. Repeat 10 times
on each side.

17
WARRANTY
LIMITED WARRANTY MODEL 15-1350
Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation for a period of 90 days on the parts and one year on the
frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT
APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE,
ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAIR,
REPLACEMENT,SUBSTITUTION OR USE WITH PARTSOTHER THAN PARTSPROVIDED BYSTAMINA
PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health clubs, spas,
gymnasiums, exercise facilities, and other public or semipublic facilities whether or not the product's use is
in furtherance of a profit making enterprise, and all other use which is not for personal, family, or household
purposes.
To implement this limited warranty, send a written notice stating your name, date, and place of purchase and
abriefdescriptionof the defectalong withyourreceiptto Stamina Products, Inc. P.O. Box 1071, Springfield
Missouri, USA, 65801-1071, or email us at [e-mail], or call us at
1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to return the
product or part to us for free repair or replacement at our option. NO ACTION FOR BREACH OF THIS
LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE DATE THE
ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR BREACH OF
ANY IMPLIEDWARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEARAFTERDELIVERYOF
THE PRODUCT TO THE PURCHASER. This limited warranty is not transferable. IF ANY PART OF THE
PRODUCT ISNOT IN COMPLIANCE WITH THIS LIMITEDWARRANTYORANY IMPLIEDWARRANTY,
THE REMEDY OF REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDYAVAILABLE TO YOU. In
theeventthatthe purchasermakesanyclaimunderthis limitedwarrantyor anyimpliedwarranty, theWarrantor
reserves the right to require the product to be returned for inspection, at the purchaser's expense, to the
Warrantor'spremisesin Springfield,Missouri.Returnofthe enclosedwarrantyregistrationcard isnotrequired
for warranty coverage, but is merely a way of establishing the date and place of purchase.
Stamina Products, Inc. SHALLNOT BE LIABLE FOR THE LOSS OF USE OFANY PRODUCT, LOSS OF
TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIALOR INCIDENTALDAMAGESDUE TO BREACH OF THEABOVEWARRANTYORANYIMPLIED
WARRANTY.
This limited warranty is the only written or express warranty given by Stamina Products, Inc. This warranty
gives you specific legal rights, and you may also have other legal rights which vary from state to state.
ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE, IS LIMITED INDURATION TO THE
DURATION OF THIS WARRANTY.
The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods to
disclaim or limit implied warranties and consequential and incidental damages with respect thereto. If any
suchlaw is foundtobe applicable, the foregoingdisclaimersand limitations ofandon impliedwarranties and
consequential and incidental damages with respect thereto shall be disregarded and shall be deemed not to
have been made to the extent necessary to comply with such legal restriction.

PRODUCT PARTS DRAWING
18
FRONT
BACK
Strap A
Strap B

1 Front Frame 1
2 Front Stabilizer 1
3 Rear Frame 1
4 Rear Stabilizer 1
5 Left Seat Frame 1
6 Right Seat Frame 1
7 Left Handrail 1
8 Right Handrail 1
9 Crank 1
10 Bearing Housing 2
11 Ball Bearing 2
12 Inside Bearing Collar 1
13 Outside Bearing Collar 1
14 Bearing Washer 1
15 Bearing Snap Washer 1
16 Bearing Nut 2
17 Pulley 1
18 V-Ribbed Belt 1
19 Idler Arm 1
20 Idler Wheel 1
21 Idler Wheel Spacer 1
22 Tension Spring 1
23 Magnetic Unit 1
24 Tension Cable 1
25 Tension Knob 1
26 Meter Post 1
27 Meter 1
28 Sensor Wire 1
29 Magnet 1
30 Foam Pad 3
31 Left Cover 1
32 Right Cover 1
33 Cover Cap 2
34 Left Pedal 1
35 Right Pedal 1
36 Endcap (50mm) 2
37 Adjustment Knob 1
38 Bushing 1
39 Inner Bushing 1
40 Leveling Cap (50mm) 2
41 Seat Cushion 1
42 Back Cushion 1
43 Foam Grip 2
44 Round Plug (25.4mm) 2
45 Round Plug (50mm) 1
46 Square Plug (25.4mm x 25.4mm) 4
47 Carriage Bolt (M8 x 1.25 x 65mm) 4
PARTS LIST
19
PART# PART NAME QTY

48 Bolt, Button Head (M8 x 1.25 x 15mm) 1
49 Bolt, Button Head (M10 x 1.5 x 122mm) 2
50 Bolt, Hex Head (M6 x 1 x 37mm) 4
51 Bolt, Round Head (M6 x 1 x 35mm) 8
52 Bolt, Flat Head (M10 x 1.5 x 20mm) 1
53 Bolt, Flat Head (M10 x 1.5 x 35mm) 1
54 Screw, Round Head (M5 x 0.8 x 15mm) 4
55 Screw, Flat Head (M5 x 0.8 x 10mm) 1
56 Screw, Flat Head (M4 x 15mm) 2
57 Screw, Big Round Head (M5 x 15mm) 2
58 Screw, Round Head (M4 x 25mm) 5
59 Nylock Nut (M10 x 1.5 x 9mm thick) 4
60 Acorn Nut (M6 x 1) 4
61 Acorn Nut (M8 x 1.25) 4
62 Thin Nut (3/8" - 26 x 5/32" thick) 2
63 Nut (3/8" - 26 x 9/32" thick) 2
64 Arc Washer (M6) 4
65 Arc Washer (M8) 5
66 Lock Washer (M6) 4
67 Lock Washer (M8) 5
68 Large Washer (ø16.5 x ø32 x 0.5mm thick) 1
69 Washer (M10) 2
70 Screw, Round Head (M5 x 0.8 x 6mm) 1
71 Warning Label 1
72 Wrench 1
73 Allen Wrench (6mm) 1
74 Manual 1
PARTS LIST
20
PART# PART NAME QTY