Standard Horizon HX380 User manual

HX380
VHF FM Marine Transceiver
Owner’s Manual

HX380Page 2
TABLE OF CONTENTS
WARNING! FCC RF EXPOSURE REQUIREMENTS..................................................................... 4
1. GENERAL INFORMATION......................................................................................................... 6
1.1 INTRODUCTION................................................................................................................. 6
1.2 RF EXPOSURE SAFETY STATEMENT ............................................................................. 6
2. ACCESSORIES .......................................................................................................................... 7
2.1 PACKING LIST.................................................................................................................... 7
2.2 OPTIONS ............................................................................................................................ 7
3. ABOUT THIS RADIO .................................................................................................................. 8
3.1 ABOUT THE VHF MARINE BAND...................................................................................... 8
3.2 ABOUT THE LMR CHANNELS........................................................................................... 8
3.3 ABOUT WATER RESISTANCE........................................................................................... 8
3.4 EMERGENCY (CHANNEL 16 USE)................................................................................... 8
3.5 CALLING ANOTHER VESSEL (CHANNEL 16 OR 9)......................................................... 9
3.6 OPERATING ON CHANNEL 13........................................................................................ 10
3.7 OPERATING ON CHANNEL 67........................................................................................ 10
3.8 SIMPLEX/DUPLEX CHANNEL USE................................................................................. 10
4. GETTING STARTED................................................................................................................. 12
4.1 RADIO CARE.................................................................................................................... 12
4.2 BELT CLIP INSTALLATION............................................................................................... 12
4.3 BATTERIES AND CHARGERS......................................................................................... 13
4.3.1 BATTERY SAFETY.................................................................................................. 13
4.3.2 BATTERY INSTALLATION AND REMOVAL............................................................ 14
4.3.3 BATTERY CHARGING ............................................................................................ 15
5. CONTROLS AND INDICATORS............................................................................................... 16
5.1 CONTROLS AND SWITCHES.......................................................................................... 16
5.2 LCD INDICATORS ............................................................................................................ 19
6. BASIC OPERATION ................................................................................................................. 20
6.1 INITIAL SETUP ................................................................................................................. 20
6.2 RECEPTION ..................................................................................................................... 20
6.3 TRANSMISSION............................................................................................................... 20
6.3.1 TRANSMIT TIME - OUT TIMER (TOT).................................................................... 21
6.4 USA, CANADIAN, AND INTERNATIONAL CHANNELS................................................... 21
6.5 NOAA WEATHER CHANNELS......................................................................................... 22
6.5.1 NOAA WEATHER ALERT........................................................................................ 22
6.5.2 NOAA WEATHER ALERT TESTING ....................................................................... 22
6.6 KEYPAD LOCKING........................................................................................................... 23
6.7 PRESET CHANNELS (0 ~ 9): INSTANT ACCESS ........................................................... 23
6.7.1 PROGRAMMING..................................................................................................... 23
6.7.2 OPERATION............................................................................................................ 23
6.8 MEMORY SCAN ............................................................................................................... 24
6.8.1 PROGRAMMING SCAN MEMORY......................................................................... 24
6.8.2 OPERATION............................................................................................................ 24
6.9 PRIORITY SCAN .............................................................................................................. 25
6.10 DUAL WATCH................................................................................................................. 26
6.11 TRI-WATCH..................................................................................................................... 26
7. MENU (“SET”) MODE .............................................................................................................. 27
8. MAINTENANCE........................................................................................................................ 30
8.1 GENERAL ......................................................................................................................... 30
8.2 REPLACEMENT PARTS................................................................................................... 30
8.3 FACTORY SERVICE......................................................................................................... 31
8.4 TROUBLESHOOTING CHART......................................................................................... 31
9. VHF MARINE CHANNEL ASSIGNMENTS .............................................................................. 32
10. WARRANTY............................................................................................................................ 36
ON-LINE WARRANTY REGISTRATION ................................................................................ 38
11. INSTALLATION OF OPTION .................................................................................................. 39
11.1 FBA-40 ALKALINE BATTERY TRAY............................................................................... 39
12. SPECIFICATIONS................................................................................................................... 40
12.1 GENERAL ....................................................................................................................... 40
12.2 TRANSMITTER............................................................................................................... 40
12.3 RECEIVER...................................................................................................................... 41
FCC AND CANADA RADIO LICENSE INFORMATION................................................................ 42

Page 3HX380
Quick RefeRence Guide
This transceiver is equipped with the E2O (Easy-To-Operate) system. You can
do the basic operation in numerical order of the illustration below.

[PWR/VOL]Knob
Rotate this knob
clockwise to turn on
the radio, and adjust
the audio level.
[SQL]Button
Press this key first,
then press the []
key to squelch or
press the []key
to un-squelch the
radio.

[]/[]Buttons
Selects the operat-
ing channel.
MIC
When transmitting,
position your mouth
1 inch (2.5 cm)
away from the small
mic hole.
Speak slowly and
clearly into the mi-
crophone.

[16/9]Button
Press to recall
channel 16.
Press and hold to
recall channel 9.

[H/L()] Button
Press to toggle the
transmit power be-
tween High (5W)
and Low (1W).

[PTT]Switch
Speak into the
micro-phone in a
normal voice level
while pressing this
switch.

HX380Page 4
WARNING! FCC RF EXPOSURE REQUIREMENTS
This Radio has been tested and complies with the Federal Communications
Commission (FCC) RF exposure limits for Occupational Use/Controlled ex-
posure environment. In addition, it complies with the following Standards and
Guidelines:
FCC 96-326, Guidelines for Evaluating the Environmental Effects of Ra-
dio-Frequency Radiation.
FCC OET Bulletin 65 Edition 97-01 (2001) Supplement C, Evaluating Com-
pliance with FCC Guidelines for Human Exposure to Radio Frequency
Electromagnetic Fields.
ANSI/IEEE C95.1-1992, IEEE Standard for Safety Levels with Respect to
Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300
GHz.
ANSI/IEEE C95.3-1992, IEEE Recommended Practice for the Measure-
ment of Potentially Hazardous Electromagnetic Fields - RF and Microwave.
WARNING:
This radio generates RF electromagnetic energy during transmit mode. This
radio is designed for and classied as Occupational Use Only, meaning it
must be used only during the course of employment by individuals aware of
the hazards, and the ways to minimize such hazards. This radio is not intend-
ed for use by the General Population in an uncontrolled environment.
CAUTION:
To ensure that your expose to RF electromagnetic energy is within the FCC al-
lowable limits for occupational use, always adhere to the following guidelines:
This radio is NOT approved for use by the general population in an uncon-
trolled exposure environment. This radio is restricted to occupational use,
work related operations only where the radio operator must have the knowl-
edge to control his or her RF exposure conditions.
When transmitting, hold the radio in a vertical position with its microphone 1
inche (2.5 cm) away from your mouth and keep the antenna at least 1 inch-
es (2.5 cm) away from your head and body.
The radio must be used with a maximum operating duty cycle not exceed-
ing 50%, in typical Push-to-Talk congurations.
DO NOT transmit for more than 50% of total radio use time (50% duty cy-
cle). Transmitting more than 50% of the time can cause FCC RF exposure
compliance requirements to be exceeded.
SAR compliance for body-worn use was only demonstrated for the specif-
ic belt-clip (CLIP-
920). Other body-worn accessories or congurations may
NOT comply with the FCC RF exposure requirements and should be avoided.

Page 5HX380
The CLIP-920 belt-clip must be used in order to comply with the FCC/IC RF
exposure requirements.
Always use Standard Horizon authorized accessories.
The information listed above provides the user with the information needed
to make him or her aware of RF exposure, and what to do to assure that
this radio operates with the FCC RF exposure limits of this radio.
Electromagnetic Interference/Compatibility
During transmissions, this radio generates RF energy that can possibly
cause interference with other devices or systems. To avoid such interfer-
ence, turn off the radio in areas where signs are posted to do so.
Do not operate the transmitter in areas that are sensitive to electromagnetic
radiation such as hospitals, health care facilities, aircraft, and blasting sites.

HX380Page 6
1. GENERAL INFORMATION
1.1 INTRODUCTION
Congratulations on your purchase of the HX380! Whether this is your first
portable marine VHF transceiver, or if you have other STANDARD HORIZON
equipment, the STANDARD HORIZON organization is committed to ensuring
your enjoyment of this high performance transceiver, which should provide
you with many years of satisfying communications even in the harshest of
environments. STANDARD HORIZON technical support personnel stands
behind every product sold, and we invite you to contact us should you require
technical advice or assistance.
The HX380 is a Submersible 5-Watt portable two way marine transceiver with
the capability to be programmed with 40 LMR (Land Mobile Radio) channels
with CTCSS or DCS signalling by a dealer. The transceiver has all allocated
International, Canadian, or USA channels. It has emergency channel 16 which
can be immediately selected from any channel by pressing the key.
The HX380 includes the following features: 10 PRESET channels for enabling
the instant access, Memory Scanning, Priority Scanning, Battery Saver, easy-
to-read large LCD display, EEPROM memory back-up, Battery Life displayed
on the LCD, and a transmit Time-Out Timer (TOT).
The HX380 transmitter provides a full 5 Watt of transmit power and also is se-
lectable to 1 Watt to assist the user in ensuring maximum battery life.
We appreciate your purchase of the HX380, and encourage you to read this
manual thoroughly, so as to learn and fully understand the capabilities of the
HX380.
1.2 RF EXPOSURE SAFETY STATEMENT
Your wireless handheld portable transceiver contains a low power transmitter.
When the Push-To-Talk (PTT: )button is pushed, the transceiver sends out
radio frequency (RF) signals.
This device is authorized to operate at a duty factor not to exceed 50% (this
corresponds to 50% transmission time and 50% reception time).
This transmitter and its antenna must maintain a separation distance of at
least 1 inch (2.5 cm) from your face. Speak in a normal voice, with the anten-
na pointed up and away from the face at the required separation distance.
Use only the supplied antenna. Unauthorized antennas, modications, or at-
tachments could damage the transmitter.

Page 7HX380
2. ACCESSORIES
2.1 PACKING LIST
When the package containing the transceiver is rst opened, please check it
for the following contents:
HX380 Transceiver
CAT460 Antenna (Antenna gain: -1.5 dBi, Impedance: 50 ohm)
FNB-V105LI 7.4 V Li-Ion Battery Pack
CD-48 Charger Cradle for HX380
SAD-11B or SAD-18B 120VAC Wall Charger for CD-48
E-DC-19A DC Cable with 12 V Cigarette Lighter Plug
Belt Clip
Owner’s Manual
2.2 OPTIONS
①MH-73A4B Speaker/Microphone
②MH-57A4B Mini Speaker/Micro-
phone
③SSM-14A Submersible Speaker/
Microphone
④SSM-64A VOX Headset
⑤SSM-55A Earpiece/Microphone
⑥CN-3 Radio-to-Ship’s An-
tenna Adapter
⑦CD-48 Charger Cradle
⑧FNB-V105LI 7.4 V Li-Ion Battery
Pack
⑨FBA-40 Alkaline Battery Case
⑩SAD-18B AC Wall Charger for
the FNB-V105LI
⑪E-DC-19A DC Cable with 12 V
Cigarette Lighter Plug
⑫E-DC-6 DC Cable; plug and
wire only
Note: Before operating the HX380 for
the first time, it is recommended that
the battery be charged. Please see
section “4.3.3 BATTERY CHARGING”
for details. ⑪
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
⑫

HX380Page 8
3. ABOUT THIS RADIO
3.1 ABOUT THE VHF MARINE BAND
The radio frequencies used in the VHF marine band lie between 156 and 162
MHz. The marine VHF band provides communications over distances that
are essentially “Line of sight” Actual transmission range depends much more
on antenna type, gain and height than on the power output of the transmitter.
On a xed mount 25 W radio transmission expected distances can be greater
than 15 miles, for a portable 5 W radio transmission the expected distance
can be greater than 5 miles in “Line of sight”.
The user of a Marine VHF radio is subject to severe nes if the radio is used
on land. The reasoning for this is you may be near an inland waterway, or
propagation anomalies may cause your transmission to be heard in a water-
way. If this occurs, depending upon the marine VHF channel on which you are
transmitting, you could interfere with a search and rescue case, or contribute
to a collision between passing ships. For VHF Marine channel assignments
refer to page 32 section 9.
3.2 ABOUT THE LMR CHANNELS
The HX380 is capable of being programmed with 40 LMR (Land Mobile Ra-
dio) channels by a dealer. The frequency range is 134 to 174MHz which may
be setup for 25 kHz (wide) or 12.5 kHz (narrow) channel stepping with CTCSS
and DCS signaling. Contact your dealer for further details.
3.3 ABOUT WATER RESISTANCE
Water resistance of the transceiver is ensured only when the battery pack is
attached to the transceiver and MIC/SP cap is installed in the MIC/SP jack.
3.4 EMERGENCY (CHANNEL 16 USE)
Channel 16 is known as the Hail and Distress Channel. An emergency may be
dened as a threat to life or property. In such instances, be sure the transceiv-
er is on and set to “Channel 16”. Then use the following procedure:
1. Press the PTT (Push-To-Talk: )switch and say “Mayday, Mayday, May-
day. This is _____, _____, _____” (your vessel’s name).
2. Then repeat once: “Mayday, _____” (your vessel’s name).
3. Now report your position in latitude/longitude, or by giving a true or magnet-
ic bearing (state which) to a well-known landmark such as a navigation aid
or geographic feature such as an island or harbor entry.
4. Explain the nature of your distress (sinking, collision, aground, re, heart
attack, life-threatening injury, etc.).
5. State the kind of assistance your desire (pumps, medical aid, etc.).
6. Report the number of persons aboard and condition of any injured.

Page 9HX380
7. Estimate the present seaworthiness and condition of your vessel.
8. Give your vessel’s description: length, design (power or sail), color and oth-
er distinguishing marks. The total transmission should not exceed 1 minute.
9. End the message by saying “OVER”. Release the PTT ( ) switch and lis-
ten.
10. If there is no answer, repeat the above procedure. If there is still no re-
sponse, try another channel.
3.5 CALLING ANOTHER VESSEL (CHANNEL 16 OR 9)
Channel 16 may be used for initial contact (hailing) with another vessel.
However, its most important use is for emergency messages. This channel
must be monitored at all times except when actually using another channel.
It is monitored by the U.S. and Canadian Coast Guards and by other vessels.
Use of channel 16 for hailing must be limited to initial contact only. Calling
should not exceed 30 seconds, but may be repeated 3 times at 2-minute in-
tervals. In areas of heavy radio traffic, congestion on channel 16 resulting
from its use as a hailing channel can be reduced signicantly in U.S. waters
by using Channel 9 as the initial contact (hailing) channel for non-emergency
communications. Also hailing on channel 9, the calling time should not exceed
30 seconds but may be repeated 3 times at 2-minute intervals.
Prior to making contact with another vessel, refer to the channel charts in this
manual, and select an appropriate channel for communications after initial con-
tact. For example, Channels 68 and 69 of the U.S. VHF Charts are some of the
channels available to non-commercial (recreational) boaters. Monitor your de-
sired channel in advance to make sure you will not be interrupting o ther trafc,
and then go back to either channel 16 or 9 for your initial contact.
When the hailing channel (16 or 9) is clear, state the name of the other vessel
you wish to call and then “this is” followed by the name of your vessel and
your Station License (Call Sign). When the other vessel returns your call, im-
mediately request another channel by saying “go to”, the number of the other
channel, and “over”. Then switch to the new channel. When the new channel
is not busy, call the other vessel.
After a transmission, say “over”, and release the PTT (Push-To-Talk: )
switch. When all communication with the other vessel is completed, end the
last transmission by stating your Call Sign and the word “out”. Note that it is
not necessary to state your Call Sign with each transmission, only at the be-
ginning and end of the contact.
Remember to return to Channel 16 when not using another channel.

HX380Page 10
3.6 OPERATING ON CHANNEL 13
Channel 13 is used at docks, bridges and for maneuvering in port. Messages
on this channel must concern navigation only, such as meeting and passing
in restricted waters. In emergencies and when approaching blind river bends,
High power is allowed. Pressing the key will change the power output
from Low Power (1 Watt) to High (5 Watts). When you change from this chan-
nel then return to it, low power will be automatically selected.
3.7 OPERATING ON CHANNEL 67
When channel 67 is used for navigational bridge-to-bridge traffic between
ships, High power may be used temporarily (in the USA band) by pressing the
key. When release the PTT switch, the transceiver will revert to low pow-
er.
3.8 SIMPLEX/DUPLEX CHANNEL USE
Refer to the VHF MARINE CHANNEL CHART (page 32) for instructions on
use of simplex and duplex channels.
NOTE
All channels are factory-programmed in accordance with FCC, Industry
Canada, and International regulations. The mode of operation cannot be
altered from simplex to duplex or vice-versa. Simplex (ship to ship) or du-
plex (marine operator) mode is automatically activated, depending on the
channel and whether the USA, Canadian or International operating band
is selected.

Page 11HX380
MEMO

HX380Page 12
4. GETTING STARTED
4.1 RADIO CARE
CAUTION
Before following the instructions below, insure the battery pack is in place
and rmly connected. Care must be taken if the radio was dropped and a
close inspection may be needed to insure the radio case and gaskets are
in adequate condition.
The design of the HX380 allows water to enter between the radio and the bat-
tery pack, however waterproof performance is not compromised.
After using the HX380 in salt water environment is recommended to clean the
radio with fresh water by rinsing the battery and radio (separately) under a
sink facet or by dunking in a fresh water. After washing,use a soft cloth to thor-
oughly dry all parts of the radio and battery.
This will keep the radio parts and the battery clean and in top operating condition.
4.2 BELT CLIP INSTALLATION
Insert the mounting screw through the belt clip, and affix it snugly to the
mounting hole on the back of the transceiver.
CAUTION
Do not install the supplied Belt Clip Mounting Screws if you are not install-
ing the Belt Clip! Also, do not use an improper screw for mounting the Belt
Clip! An improper screw may cause a “short circuit” to the internal circuitry,
causing serious damage!
Belt Clip Tab
Mounting Screw

Page 13HX380
4.3 BATTERIES AND CHARGERS
If the radio has never been used, or its charge is depleted, it may be
charged by connecting the CD-48 Charger Cradle with the SAD-11B or SAD-
18B Battery Charger, as shown in the illustration. If 12V DC power is avail-
able, the supplied E-DC-19A DC Cable with 12 V Cigarette Lighter Plug may
be used for charging the battery. The SAD-11B or SAD-18B and E-DC-19A
will charge a completely discharged FNB-V105LI battery pack in approximate-
ly 3 hours.
The FNB-V105LI is a high performance Li-Ion battery providing high capacity
in a compact package.
CAUTION
To avoid risk of explosion and injury, FNB-V105LI battery pack should
only be removed, charged or recharged in non-hazardous environments.
4.3.1 BATTERY SAFETY
Battery packs for your transceiver contain Li-Ion batteries. This type of bat-
tery stores a charge powerful enough to be dangerous if misused or abused,
especially when removed from the transceiver. Please observe the following
precautions:
DO NOT SHORT BATTERY PACK TERMINALS: Shorting the terminals that
power the transceiver can cause sparks, severe overheating, burns, and bat-
tery cell damage. If the short is of sufcient duration, it is possible to melt bat-
tery components. Do not place a loose battery pack on or near metal surfaces
or objects such as paper clips, keys, tools, etc. When the battery pack is in-
stalled on the transceiver, the terminals that transfer current to the transceiver
are not exposed. The terminals that are exposed on the battery pack when it
is mounted on the transceiver are charging terminals only and do not consti-
tute a hazard.
DO NOT INCINERATE: Do not dispose of any battery in a re or incinerator.
The heat of re may cause battery cells to explode and/or release dangerous gases.
Battery Maintenance
For safe and proper battery use, please observe the following:
Battery packs should be charged only in non-hazardous environments;
Use only STANDARD HORIZON-approved batteries;
Use only a STANDARD HORIZON approved charger. The use of any other
charger may cause permanent damage to the battery.
Follow charging instructions provided with the chargers.
Keep the battery contacts clean and dry.

HX380Page 14
Battery Storage
Store the batteries in a cool place to maximize storage life. Since batteries are
subject to self-discharge, avoid high storage temperatures that cause large
self-discharge rates. After extended storage, a full recharge is recommended.
Battery Recycling
DO NOT PLACE USED BATTERIES IN YOUR REGULAR TRASH!
LI-ION BATTERIES MUST BE COLLECTED, RECYCLED OR DISPOSED
OF IN AN ENVIRONMENTALLY SOUND MANNER.
The incineration, land lling or mixing of Li-Ion batteries with the municipal sol-
id waste stream is PROHIBITED BY LAW in most areas.
Return batteries to an approved Li-Ion battery recycler. This may be where
you purchased the battery.
Contact your local waste management ofcials for other information regarding
the environmentally sound collection, recycling and disposal of Li-Ion batter-
ies.
4.3.2 BATTERY INSTALLATION AND REMOVAL
To install the battery pack, hold the trans-
ceiver with your left hand, so your palm is
over the speaker. Insert the battery pack
into the battery compartment on the back
of the radio, then push the bottom side
of the battery pack until the battery pack
locks with the Battery Pack Latch.
To remove the battery, turn the radio off. Slide the Battery Pack Latch on
the bottom of the radio, then lift up on the bottom of the battery and remove
it from the radio.

Page 15HX380
4.3.3 BATTERY CHARGING
1. Turn the transceiver off.
2. Insert the DC plug from the SAD-11B or
SAD-18B into the DC jack on the CD-
48 side panel, then plug the SAD-11B
or SAD-18B into the AC line outlet.
3. Insert the HX380 (with the battery pack)
into the CD-48; the antenna should be
at the left side when viewing the char-
ger from the front.
4. If the HX380 is inserted correctly, the
Red “CHARGING” indicator will glow.
A fully-discharged pack will be charged
completely in approximately 7 hours.
5. When charging is completed, the red
LED indicator will change to green. Remove the transceiver from the CD-
48, and unplug the SAD-11B or SAD-18B from the AC line outlet.
WARNING
Do not reverse-connect the battery terminals.
Do not parallel-connect the battery terminals.
Do not change batteries in hazardous locations.
To reduce the risk of explosion, recharge the batteries outside of
hazardous locations.
CAUTION
The CD-48 cradle is NOT designed to be waterproof. Do not attempt to
charge in water hazardous locations.
NOTE
The CD-48 cradle is only designed for the charging of the HX380’s battery,
and is not suitable for other purposes. The CD-48 may contribute noise to
TV and radio reception in the immediate vicinity, so we do not recommend
its use adjacent to such device.
SAD-11B
or
SAD-18B
CD-48

HX380Page 16
5. CONTROLS AND INDICATORS
5.1 CONTROLS AND SWITCHES
NOTE
This section denes each control of the transceiver. For detailed operating
instructions, refer to section “6. BASIC OPERATION”. Refer to illustra-
tions for the location of the following controls, switches, and connections.
ANT Jack (Top Panel)
The supplied CAT460 flexible an-
tenna is attached here.
MIC/SP Jack (Top Panel)
The jack accepts the optional
SSM-14A Submersible Speaker/
Microphone, MH-73A4B Speak-
er/Microphone, MH-57A4B Mini
Speaker/Microphone, SSM-64A
VOX Headset, or SSM-55A Ear-
piece/Microphone. When this jack
is used, the internal speaker and
microphone are disabled.
1) Do not allow the HX380
to become submerged
in water while the plastic cover
over the MIC/SP jack is removed.
2) Do not remove/install the op-
tional Speaker Microphone in a
hazardous location.
POWER Switch / VOLUME Con-
trol (VOL)
Turns the transceiver on and off as well as adjusts the audio volume level.
Turn this knob clockwise to turn the radio on and increase the speakers au-
dio volume.
Turn fully counter-clockwise to turn the radio off.
PTT (PUSH-TO-TALK)Switch
When pushed activates the transmitter.
LCD Display
This display shows current operating conditions. Refer to page 19 for details.

Page 17HX380
Keypad
Key
Pressing this key immediately recalls channel 16 from any channel location.
Holding down this key recalls channel 9. Pressing this key again reverts to
the previous selected working channel.
Secondary use:
When the key is held and the key is pressed, the radio will change
the marine band between the International, Canadian, and USA channels.
Advanced use:
When the key is held and the key is pressed, the radio will change
the priority channel between the Channel 16, Channel 9, and the Preset
Channel.
Key
Press this key to toggle the transmitter output power between “High” (5
Watts) and “Low” (1 Watt) power. When the “Low” power is selected, the “
” icon will appear to the right of the channel indication on the display. This
key does not function on the “Transmission Inhibited” and “Low power only”
channels.
Secondary use:
Hold down this key to lock the keypad (except the , and PTT (
)keys) so that they are not accidentally changed. The “ ” icon will ap-
pear at the right of the channel indication on the display, to indicate that the
functions are locked. Hold down this key until the “ ” icon disappears to
unlock the radio.
Advanced use:
When the key is held and the key is pressed, the radio will change
the priority channel between the Channel 16, Channel 9, and the Preset
Channel.
Key
Press this key to recall the user preset memory channels (shown as memo-
ry channel number “0” - “9” on the display). Press the or key to select
the desired preset channel.
Press and hold this key for two seconds to memorize the selected channel
into the preset memory.
Key
Press the key momentarily to increase the channel one step. Hold the key
down to increase the channel continuously.
Secondary use:
Used to adjust the squelch threshold level up after the key is pressed.

HX380Page 18
Key
Press the key momentarily to decrease the channel one step. Hold the key
down to decrease the channel continuously.
Secondary use:
Used to adjust the squelch threshold level down after the key is
pressed.
Key
Press this key to activate the squelch adjusting mode. Press the
or key to adjust the squelch threshold level.
Secondary use:
Press and hold this key for two seconds to open the squelch, allowing you
to monitor the operating channel. Release the key to resume normal (quiet)
monitoring.
Key
Starts scanning and priority scanning of programmed channels.
Secondary use:
Press and hold the key for two seconds to activate the Dual Watch feature.
Key
Press to stop the Scan, Priority Scan, or Dual Watch feature.
Secondary use:
Press and hold this key to immediately recall the last-used NOAA Weather
Channel from any channel location. Recalls the previously- selected work-
ing channel when the key is pressed again.
Advanced use:
When the key is held and the key is pressed, the radio will change
the marine band between the USA, International, and Canadian channels.
Speaker
The internal speaker is located here.
Microphone
The internal microphone is located here.
When transmitting, position your mouth 1 inch (2.5 cm) away from the small
mic hole. Speak slowly and clearly into the microphone.
Battery Pack Lock (Bottom side)
Slide the Battery Pack Lock to the “” position for battery removal.

Page 19HX380
5.2 LCD INDICATORS
Alpha/numeric “Tag” display
Indicates the current channel name or
operating mode.
“PRI” Indicator
This indicator is shown when the Prior-
ity channel is selected.

“” Indicator
This indicator appears when a signal
is being received or when the radio is unsquelched.
“U/I/C” Indicator
These indicators show the “band” of operation for the particular channel. “U”
indicates the USA band; “I” indicates the International band; and “C” indi-
cates the Canadian band.
“P” Indicator
This indicator shows the channel is in the “PRESET” channel memory.
“ ” Battery Indicator
“ ”: Full battery
“ ”: Lower battery
“ ”: Battery is very low
“ (Blinking)”: Prepare to charge the battery
Channel Display
The operating channel is shown on the LCD in both the transmission and
reception modes.
“ ” Indicator
This indicator appears during transmission.
“ ” Indicator
When the “ ” icon is shown on the LCD, all keys are disabled except for
the PTT ( ), , and keys.
“ ” Indicators
This indicator shows when the TX output power is selected to “Low”
(1 Watt) power.

HX380Page 20
6. BASIC OPERATION
6.1 INITIAL SETUP
1. Install the battery pack on the transceiver (see section “4.3.2 BATTERY IN-
STALLATION AND REMOVAL”).
2. Install the antenna onto the transceiver; hold the bottom end of the anten-
na, then screw it onto the mating connector on the transceiver until it is
snug. Do not over-tighten.
6.2 RECEPTION
1. Turn the VOL knob clockwise to turn the trans-
ceiver on.
The battery voltage will appear briey at the upper
left corner on the display, then the channel name
will appear.
2. Press the key to activate the squelch adjusting
mode (The “SQL LVL” notation will appear). Press the
key until the “ ” indicator appears on the display,
then press the key again.
3. Turn the VOL knob clockwise until the noise or audio
from the speaker is at a comfortable level.
4. Press the key, then press the key until the
random noise disappears. This state is known as the
“Squelch Threshold”.
5. Press the or key to select the desired channel.
Refer to the channel chart on page 33 for available
channels.
6. When a signal is received, adjust the VOL knob to the
desired listening level. The “ ” indicator on the
LCD is displayed indicating that the channel is being
used.
6.3 TRANSMISSION
1. Perform “6.2 RECEPTION” discussion above.
2. Before transmitting, monitor the channel and make sure it is clear.
THIS IS AN FCC REQUIREMENT!
3. For communications over short distances, press the
key to select Low power (1 watt: “ ” icon appears).
Note: Transmitting on Low power prolongs battery life.
Low power should be selected whenever possible.