Standard TPMS User manual

IDENTIFICATION CLONING TOOL
MANUAL
IDENTIFICATION CLONING TOOL USE
The Identification Cloning Tool interacts with the tire pressure sensor
through wireless (radio frequency) communication to write the sensor
identification number onto replacement sensors.
IDENTIFICATION CLONING TOOL INTRODUCTION
LCD Display
Sensor Input
BACK Key
ENTER Key
Keypad
ON Key
9-volt battery: Remove rubber cover and install
battery in back of tool prior to operation.
KEYPAD SUMMARY
FUNCTION KEY
Power unit on
Press to turn the unit on, press and hold to turn unit off.
ENTER key, to write
identification number
Power off unit BACK key
Keypad, key in sensor
identification number
KEY FUNCTION
ON KEY: Press and hold the ON key to power the
unit off
KEYPAD: Key in sensor identification number to be
written on blank sensor
ENTER KEY: After keying in the sensor identification
number and loading sensor, pressing the Enter key
will write sensor ID number onto blank sensor.
BACK KEY: Delete undesired inputs
ID WRITING PROCEDURE (Cont’d)
STEP 4:
Press the ENTER key .
The tool will begin to write the
identification number onto the
new sensor.
STEP 5:
The screen will indicate that the
OE sensor ID number has been
written to new sensor by ‘OK!’.
STEP 6:
Place the included sticker on the new sensor and write the ID
number for future reference.
STEP 7:
Properly dispose of old sensor.
NOTE: Old sensors will transmit signals and may interfere with
new replacement sensors and the vehicle’s TPMS light may
trigger. To avoid this, place old sensors in aluminum foil or
remove from TPMS staging area.
018834F0
TX OK!_h
018834F0
ENTER...._h
To ensure correct operation and service, read
the following instructions before operating the
Identification Cloning Tool.
IDENTIFICATION CLONING TOOL SPECIFICATIONS
Dimensions: 143mm x 88mm x 35mm
Battery: 9V
Display: 2 line LCD, 30mm x 15 mm
Weight: 255g
Temperatures: Operational: 5°C to 45°C/41°F to 113°F
Storage: 0°C to 60°C/32°F to 140°F
Relative humidity: 70-80%
TYPICAL OE SENSOR ID NUMBER LOCATION
ID WRITING PROCEDURE
IMPORTANT: After removing sensor from the tire, use TPMS
Application and Illustrated Parts Guide to determine appropriate
sensor needed to replace OE sensor.
STEP 1:
Determine OE sensor identification
number by reading the sensor or
using a scan tool.
STEP 2:
Press the ON key to turn
tool on.
NOTE: Tool shuts off automatically
if left inactive for 7 seconds.
STEP 3:
Place replacement sensor into
Identification Cloning Tool and input
OE sensor identification number.
The ‘h’ or ‘d’ below ID number
represents input format:
h = hexadecimal (letters and
numbers)
d = decimal (numbers only)
To change from ‘d’ (decimal) to
‘h’ (hexadecimal), or vice versa,
press the ON key .
018834F0
h
Enter
Valve ID
FIRST FUNCTION
At power on, the tool displays the
software revision number.
SECOND FUNCTION
While the unit is on, press and hold ‘ON’
to turn the power off.
ID Code
Ver: 1.00
Bye-Bye
^0^/_
Schrader Style Sensor Pacific Style Sensor
Snap-In Style Sensor
Continental Style Sensor
Schrader Style Sensor
Seimens/Continental
Style Sensor

WHEN… NOTE...
Removing old
sensor from
vehicle
Remove from area or wrap in aluminum foil,
damaged sensors will continue to
transmit signals.
Vehicle does
not recognize
sensors
May require over-inflating tire and then
reducing psi to proper level to activate sensor.
Checking if spare
tire is equipped
with TPMS
Ensure proper air pressure and
functioning sensor.
No sensor is
detected
Ensure correct sensor is being used via the
TPMS Application and Illustrated Parts Guide.
Verify that the OE part number in the TPMS
Application and Illustrated Parts Guide
matches the OE part number of the sensor
on the vehicle.
SWITCH ON SAFELY: Do not switch on the device
when wireless tool is prohibited or when it may
cause interference or danger.
SWITCH OFF WHEN REFUELING: Do not use the
device when filling vehicle with gasoline. Do not use
near fuel or chemicals.
SWITCH OFF NEAR BLASTING: Adhere to any
restrictions. Do not use the tool when blasting is in
progress.
USE SENSIBLY: Use only in normal conditions as
indicated in product instructions. Do not touch the
antenna unnecessarily.
QUALIFIED SERVICE: Only qualified personnel may
install or repair this device.
ENHANCEMENTS AND BATTERIES: Use only approved
enhancements and batteries for the Identification
Cloning Tool. Do not connect incompatible products.
WATER RESISTANCE: This tool is not water resistant
– keep it dry.
CONNECTING TO OTHER DEVICES: When connecting
to any other device, read user guide for detailed safety
instructions. Do not connect incompatible products.
TROUBLESHOOTING GUIDE APPENDIX
The Identification Cloning Tool is a product of superior design and
craftsmanship and should be treated with care. Follow the suggestions
below to help maintain warranty coverage:
• Keep the device dry. Precipitation, humidity and all types of moisture
may contain minerals that will corrode electronic circuits. If device
does get wet, remove the battery and allow the device to dry
completely before replacing.
• Do not use or store the tool in dusty, dirty areas to keep electronic
components clean.
• Do not store the device in hot areas. High temperatures can shorten
the life of electronic devices, damage batteries and warp or melt
certain plastics.
• Do not store the device in cold areas. When the device returns to its
normal temperature, moisture can form inside the device and damage
electronic circuit boards.
• Do not attempt to open the device other than instructed in this guide.
• Do not drop, knock or shake the device. Rough handling can break
Internal circuit boards and mechanics.
• Do not use harsh chemicals, cleaning solvent or strong detergent to
clean the device. Do not paint the device. Paint can clog the moving
parts and prevent proper operation.
• Do not touch the main display with hard or angular materials. Objects
like earrings or jewelry may scratch the display.
• Use a soft, clean and dry cloth to clean the device.
• Use only the supplied antenna. Unauthorized antennas, modifications
or attachments could damage the device and may violate regulations
governing radio devices.
All of the above suggestions apply equally to your device, battery or any
enhancements.
LIMITED WARRANTY
Your new product is warranted to you, the original customer to be free of
defects in material and workmanship (as determined solely by Standard
Motor Products, Inc.) for 1 year from the date of purchase, subject to the
limitations below. Standard Motor Products, Inc. will repair or replace, at its
option, the product if it is proven defective under normal use and service.
The product must be shipped prepaid. Proof of the date of sale to the
original customer may be required.
This warranty does not include labor or cover the cost of any other
components or labor required to restore the motor vehicle to its proper
operating condition.
This warranty does not apply to products that have been: 1) altered;
2) improperly installed, maintained or repaired or installed on a second
engine or motor vehicle; 3) damaged by accident, negligence or misuse;
4) used in commercial, fleet, heavy duty, off road, public or governmental
vehicles; or 5) returned with missing components or parts that were
originally included in the package.
THE WARRANTIES SET FORTH HEREIN ARE IN LIEU OF ALL OTHER
WARRANTIES, WHETHER EXPRESS OR IMPLIED. ALL IMPLIED
WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED AFTER THREE
(3) YEARS. STANDARD MOTOR PRODUCTS, INC. IS NOT RESPONSIBLE
FOR INJURY, PROPERTY DAMAGE OR OTHER INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING DIRECTLY OR INDIRECTLY OUT OF
THE USE OF THIS PRODUCT (REGARDLESS OF THE FORM OF ACTION),
NOTWITHSTANDING THE FACT THAT SAID INJURY, PROPERTY DAMAGE
OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES AROSE DIRECTLY
OR INDIRECTLY FROM AN ACTUAL OR ALLEGED DEFECT IN MATERIAL
AND/OR WORKMANSHIP.
Some states do not allow limitations on how long an implied warranty lasts,
or the exclusion of limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you. This warranty gives
you specific legal rights. You may also have other rights that vary from state
to state.
RF NOTICE
This device meets guidelines for exposure to radio waves.
This device is a radio transmitter. It is designed not to exceed the limits
for exposure to radio waves recommended by international guidelines.
These guidelines were developed by the independent scientific organization
ICNIRP and include safety margins designed to assure the protection off all
persons, regardless of age and health.
The SAR value for this device is less than 5A/m. This value is the reference
level for general public exposure to time varying electric and magnetic fields
(unperturbed rms values) for the 3-150 kHz frequency range.
IDENTIFICATION CLONING TOOL SAFETY TIPS
This device is a radio transmitter.
FCC NOTICE
This device complies with Part 15 of the FCC Rules and Industry Canada
licence-exempt RSS-210 standard.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device.
WARNING: Any changes or modifications in construction of this device
which are not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.