Standard SD460 User manual

OPERATORS MANUAL
Standard SD460 / SD700 Digital Duplicators
Read this manual, and thoroughly
familiarize yourself with its
contents before operating or
servicing this equipment.

Introduction
This manual contains detailed instructions and notes on the operation and use of this machine. For your
safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy
place for quick reference.
Important
Contents of this manual are subject to change without prior notice. In no event will the company be li-
able for direct, indirect, special, incidental, or consequential damages as a result of handling or oper-
ating the machine.
Notes:
The model names of the machines do not appear in the following pages. Check the type of your ma-
chine before reading this mamual.
• Type1 (Pixel Density 600 ×600 dpi): SD700
• Type2 (Pixel Density 400 ×400 dpi): SD460
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the inch version.
For best performance, use genuine Standard brand inks and masters.
Standard shall not be responsible for any damage or expense that might result from the use of parts
other than genuine parts supplied by your Authorized Standard Dealer.
Power Source
120V, 60Hz, 3.2A or more
Please be sure to connect the power cord to a power source as above. For details about power source,
see p.170 “Power Connection”.
Trademark
PostScript®and Acrobat®are registered trademarks of Adobe Systems Incorporated.
Other product names used herein are for identification purposes only and might be trademarks of their
respective companies. We disclaim any and all rights to those marks.
Symbols
In accordance with IEC 60417, this machine uses the following symbols for the main switch:
•ameans POWER ON.
•bmeans POWER OFF.

i
Manuals for This Machine
The following manuals describe the operational procedures of this machine. For
particular functions, see the relevant parts of the manual.
Note
❒Manuals provided are specific to machine type.
❒Adobe Acrobat Reader/Adobe Reader is necessary to view the manuals as a
PDF file.
❖Safety Information (paper)
Describes information about the safety precautions.
❖Easy Operation Guide (paper/PDF file - CD-ROM *1 )
Describes information about the control panel and basic operations.
❖Operating Instructions (this manual)
Describes operations, functions, User Tools (initial setting, mode setting, etc.)
and troubleshooting.
❖Network Guide (PDF file - CD-ROM *1 )
Describes procedures for configuring the machine and computers in a net-
work environment.
❖Printer Reference (PDF file - CD-ROM *1 )
Describes system settings and operations for the machine's printer function.
❖Preparations for Use as a Printer (paper/PDF file - CD-ROM *1 )
Describes procedures for connecting the Ethernet and USB cables to the ma-
chine.
❖Manuals for DeskTopBinder Lite
DeskTopBinder Lite is a utility included on the CD-ROM labeled “Document
Management Utility”.
• DeskTopBinder Lite Setup Guide (PDF file - CD-ROM *2 )
Describes the installation of, and the operating environment for DeskTop-
Binder Lite in detail. This guide can be displayed from the [Setup]dialog
box when DeskTopBinder Lite is installed.
• DeskTopBinder Introduction Guide (PDF file - CD-ROM *2 )
Describes operations of DeskTopBinder Lite and provides an overview of
its functions. This guide is added to the [Start]menu when DeskTopBinder
Lite is installed.
❖Other manuals
• PostScript3 (PDF file - CD-ROM *1 )
*1 Provided on the CD-ROM labeled “Operating Instructions”
*2 Provided on the CD-ROM labeled “Document Management Utility”

ii
What You Can do with this Machine
Below is a quick summary of this ma-
chine's features and where to look for
more information.
❖Basic Procedure
See p.46 “Basic Procedure”.
❖Saving Energy
See p.48 “Saving Energy”.
❖Printing onto Various Kinds of Paper
See p.49 “Printing onto Various
Kinds of Paper”.
❖Image Rotation
See p.53 “Image Rotation”.
❖Selecting Original Type
See p.54 “Selecting Original Type”.
❖Master Making Density
See p.55 “Master Making Density”.
❖Adjusting the Position of Printed Im-
ages
See p.56 “Adjusting the Position of
Printed Images”.
*Paper feed direction
❖Changing the Printing Speed
See p.57 “Changing the Printing
Speed”.
❖Preset Reduce/Enlarge
See p.59 “Preset Reduce/Enlarge”.
❖Zoom
See p.60 “Zoom”.
❖Auto Reduce/Enlarge
See p.62 “Auto Reduce/Enlarge”.
GRPOSI0E
GRRATI0E
GRZOOM0E

iii
❖Directional Magnification (%)
See p.64 “Directional Magnifica-
tion (%)”.
❖Directional Size Magnification (Inch)
See p.65 “Directional Size Magnifi-
cation (inch)”.
❖Combine
See p.66 “Combine”.
❖Class Settings
See p.69 “Class Settings”.
❖Separate
See p.73 “Separate”.
❖Image Repeat
See p.74 “Image Repeat”.
❖Centering
See p.78 “Centering”.
CP2P01EE
CP2M01EE
ACY001S
AJK210S
GRJOBS0E
GCCNTR0E

iv
❖Erase Border
See p.78 “Erase Border”.
❖Margin Adjustment
See p.79 “Margin Adjustment”.
❖Overlay
See p.80 “Overlay”.
❖Preset Stamp
See p.82 “Preset Stamp”.
❖Make–up
See p.84 “Make-Up Printing Fea-
tures”, p.87 “Command Sheets for
Make-Up Printing”, and p.94
“Make-Up Printing”.
❖Quality Start
See p.98 “Quality Start”.
❖Economy Mode
See p.98 “Economy Mode”.
❖Skip Feed
See p.99 “Skip Feed”.
❖Security
See p.100 “Security”.
❖Conserving the Master
See p.101 “Conserving the Mas-
ter”.
❖Double Feed
See p.102 “Double Feed”.
❖Storing File
See p.103 “Storing File”.
❖Programs
See p.109 “Programs”.
❖Making Color Prints
See p.112 “Making Color Prints”.
❖Changing the Drum Size
See p.116 “Changing the Drum
Size”.
❖Printing from the computer
See Printer Reference.
ACY068S
GROVER0E
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE ABCDE ABCDE ABCDE ABCDE
GRSTAM0E

v
TABLE OF CONTENTS
Manuals for This Machine ......................................................................................i
What You Can do with this Machine ....................................................................ii
Notice ......................................................................................................................1
Information about Installed Software..........................................................................3
How to Read This Manual .....................................................................................8
Safety Information .................................................................................................9
Safety During Operation.............................................................................................9
Positions of RWARNING and RCAUTION Labels ...........................................11
Guide To Components ........................................................................................12
Options .................................................................................................................15
Option List ................................................................................................................15
Guide to Major Options ............................................................................................16
Control Panel........................................................................................................18
Display Panel ...........................................................................................................20
Turning On the Power .........................................................................................22
Turning On the Main Power .....................................................................................22
Turning On the Power ..............................................................................................23
Turning Off the Power ..............................................................................................23
Turning Off the Main Power .....................................................................................23
1. Before Using the Machine
Originals ...............................................................................................................25
Size and Weights of Recommended Originals.........................................................25
Sizes difficult to detect .............................................................................................27
Print Paper............................................................................................................28
Recommended Paper Size and Type ......................................................................28
Recommended for the LCIT.....................................................................................28
Recommended for the LCOT ...................................................................................29
Non-recommended Paper........................................................................................29
Storing Paper ...........................................................................................................31
Printing Size .........................................................................................................32
2. Basics
Printing Preparations ..........................................................................................33
Using the Paper Feed Tray and Delivery Tray.........................................................33
Using the LCIT and LCOT........................................................................................36
After Printing ........................................................................................................41
Folding the Paper Feed Tray and Delivery Tray ......................................................41
Uninstalling the LCIT................................................................................................43
Placing Originals..................................................................................................44
Placing Originals on the Exposure Glass.................................................................44
Placing Originals in the Auto Document Feeder ......................................................44
Original Orientation ..................................................................................................45

vi
Basic Procedure...................................................................................................46
Original Beeper ........................................................................................................47
Auto Reset ...............................................................................................................47
Saving Energy..........................................................................................................48
Auto Off Timer..........................................................................................................48
Printing onto Various Kinds of Paper................................................................49
Printing onto Thick Paper.........................................................................................49
Printing onto Standard Paper...................................................................................49
Printing onto Envelopes ...........................................................................................49
Printing onto Special Paper......................................................................................50
Making a Master and Prints ................................................................................51
Selecting Cycle Setting ............................................................................................52
Image Rotation.........................................................................................................53
Selecting Original Type ............................................................................................54
Master Making Density.............................................................................................55
Sample Print and Adjustment.............................................................................56
Adjusting the Position of Printed Images .................................................................56
Changing the Printing Speed ...................................................................................57
3. Printing Functions
Printing Functions ...............................................................................................59
Preset Reduce/Enlarge ............................................................................................59
Zoom ........................................................................................................................60
Auto Reduce/Enlarge ...............................................................................................62
Directional Magnification (%) ...................................................................................64
Directional Size Magnification (inch) ........................................................................65
Combine...................................................................................................................66
Class Settings ..........................................................................................................69
Separate...................................................................................................................73
Image Repeat...........................................................................................................74
Centering..................................................................................................................78
Erase Border ............................................................................................................78
Margin Adjustment ...................................................................................................79
Overlay.....................................................................................................................80
Preset Stamp ...........................................................................................................82
Make-Up Printing Features ......................................................................................84
Command Sheets for Make-Up Printing ..................................................................87
Make-Up Printing .....................................................................................................94
Quality Start .............................................................................................................98
Economy Mode ........................................................................................................98
Skip Feed .................................................................................................................99
Security ..................................................................................................................100
Conserving the Master ...........................................................................................101
Double Feed...........................................................................................................102
Storing File .........................................................................................................103
Storing Data ...........................................................................................................103
Changing a Stored File's User Name, File Name, or Password ............................105
Searching for Stored Files......................................................................................106
Printing Stored Files...............................................................................................107
Deleting Stored Files..............................................................................................108
Printing or Deleting Stored Files Using a Web Browser.........................................108

vii
Programs ............................................................................................................109
Storing a Program ..................................................................................................109
Recalling a Program...............................................................................................110
Changing a Stored Program ..................................................................................110
Changing a Program Name ...................................................................................110
Protecting a Program .............................................................................................110
Deleting a Program ................................................................................................111
Making Color Prints ...........................................................................................112
Changing the Color Drum Unit ...............................................................................112
Making Color Prints................................................................................................113
Printing in Two Colors ............................................................................................114
Changing the Drum Size ...................................................................................116
Printing Area (At 23°C/73°F, 65% RH)...................................................................116
Master Cut Length..................................................................................................116
Combination Chart.............................................................................................117
4. Troubleshooting
If Your Machine Does Not Operate as You Want ............................................119
If you Cannot Make Clear Prints.......................................................................121
Faint Prints .............................................................................................................121
Black Lines/Stained Prints .....................................................................................121
Dirty Background....................................................................................................121
If You Cannot Make Prints as You Want..........................................................124
Combine.................................................................................................................124
Storing Files ...........................................................................................................125
BLoading Paper ................................................................................................126
Loading Paper into the Paper Feed Tray ...............................................................126
Loading Paper into LCIT ........................................................................................127
jAdding Ink ......................................................................................................128
CReplacing the Master Roll .............................................................................130
xClearing Misfeeds .........................................................................................132
“x+ A” Paper Misfeeds in the Paper Feed Section..............................................132
”x+ A + B” Paper Misfeeds in the Paper Feed Section .......................................133
“x+ B” Paper or Master Wrapped Around the Drum............................................134
“x+ C” Paper Misfeeds in the Paper Exit Section................................................136
“x+ D” Master Misfeeds in the Master Feed Section...........................................137
“x+ B + D” Master Misfeeds in the Master Feed Section ....................................138
“x+ B + E” Master Misfeeds in the Master Eject Section.....................................138
“x+ E” Master Misfeeds in the Master Eject Section ...........................................139
“x+ P” Original Misfeeds Occur in the Auto Document Feeder ...........................140
When Paper Misfeeds in the LCIT .........................................................................141
Changing the Paper Size...................................................................................143
Changing the Paper Size of the Paper Feed Tray .................................................143
Changing the Paper Size of LCIT ..........................................................................144
MWhen the Open Cover/Unit Indicator Lights ...............................................145
kRemoving the Used Master...........................................................................146
When Multiple Sheets Are Fed at the Same Time...........................................147
When Prints Are Not Delivered in a Neat Stack ..............................................148
When Printing on Small Size Paper .......................................................................148

viii
5. User Tools
User Tools Menu ................................................................................................149
System Settings .....................................................................................................149
Master Making/Print Settings .................................................................................151
Accessing User Tools (System Settings/Master Making/Print Settings)......154
Changing Default Settings .....................................................................................154
Quitting User Tools ................................................................................................154
Settings You Can Change with User Tools .....................................................155
System Settings .....................................................................................................155
Master Making/Print Settings .................................................................................160
User Code ...........................................................................................................164
Registering a User Code........................................................................................164
Changing a User Code...........................................................................................165
Deleting a User Code.............................................................................................165
Displaying the Counter for Each User Code ..........................................................165
Printing the Counter for All User Codes .................................................................166
Clearing the Counter ..............................................................................................166
6. Remarks
Do's and Don'ts..................................................................................................167
Where to Put Your Machine ..............................................................................169
Machine Environment ............................................................................................169
Moving....................................................................................................................170
Power Connection..................................................................................................170
Access to the Machine...........................................................................................171
Maintaining Your Machine ................................................................................172
Cleaning the Exposure Glass.................................................................................172
Cleaning the exposure glass cover ........................................................................172
Cleaning the Auto Document Feeder.....................................................................173
Cleaning the paper feed roller (paper feed tray) ....................................................173
Cleaning the paper feed roller (LCIT).....................................................................173
Other Functions .................................................................................................174
Inquiry ....................................................................................................................174
Changing the Display Language ............................................................................175
Counter/Data Print .............................................................................................176
Displaying the Counter...........................................................................................176
Print the log data and programmed class list .........................................................176
7. Entering Text
Entering Text ......................................................................................................177
Available Characters ..............................................................................................177
Keys .......................................................................................................................177
Entering Text..........................................................................................................178

ix
8. Specifications
Main Unit.............................................................................................................179
Options ...............................................................................................................183
Auto Document Feeder (ADF: DF Type 85)...........................................................183
Twin Color Press Roller Printing System TC-IIR....................................................183
Large Capacity System (LCS: LS3000R)...............................................................184
Other Options.........................................................................................................185
Consumables .....................................................................................................186
INDEX....................................................................................................... 187

x

1
Notice
Important
Do not copy or print any item for which reproduction is prohibited by law.
Copying or printing the following items is generally prohibited by local law:
bank notes, revenue stamps, bonds, stock certificates, bank drafts, checks, pass-
ports, driver's licenses.
The preceding list is meant as a guide only and is not inclusive. We assume no
responsibility for its completeness or accuracy. If you have any questions con-
cerning the legality of copying or printing certain items, consult with your legal
advisor.
Notice To Wireless LAN Interface (optional) Users
Notes to users in the United States of America
Notice:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential in-
stallation. This equipment generates, uses and can radiate radio frequency ener-
gy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to cor-
rect the interference by one more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must ac-
cept any interference received, including interference that may cause undesired
operation.
Warning:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

2
Note to users in Canada
Note:
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the
device.
IEEE 802.11b I/F Unit Type 1:
This device complies with RSS-210 of Industry Canada.
The term “IC:” before the certification/registration number only signifies that
the Industry Canada technical specifications were met.
To prevent radio interference to the licensed service, this device is intended to
be operated indoors and away from windows to provide maximum shielding.
Equipment (or its transmit antenna) that is installed outdoors is subject to licens-
ing.
Remarque concernant les utilisateurs au Canada
Avertissement:
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Can-
ada.
L'utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1)
il ne doit pas produire de brouillage et (2) l'utilisateur du dispositif doit être prêt
á accepter tout brouillage radioélectrique reçu, même si ce brouillage est suscep-
tible de compromettre le fonctionnement du dispositif.
IEEE 802.11b I/F Unit Type 1:
Ce dispositif est conforme á la norme CNR-210 d'Industrie Canada.
L'expression «IC:» avant le numéro d'homologation/enregistrement signifie
seulement que les spécifications techniques d'Industrie Canada ont été re-
spectées.
Pour empêcher que cet appareil cause du brouillage au service faisant l'objet
d'une licence, il doit être utilisé á l'intérieur et devrait être placé loin des fenêtres
afin de fournir un écran de blindage maximal.
Si le matériel (ou son antenne d'emission) est installe á l'extérieur, il doit faire
l'objet d'une licence.

3
Information about Installed Software
expat
• The software including controller, etc. (hereinafter “software”) installed on
this product uses the expat Version 1.95.2 (hereinafter “expat”) under the con-
ditions mentioned below.
• The product manufacturer provides warranty and support to the software of
the product including the expat, and the product manufacturer makes the ini-
tial developer and copyright holder of the expat, free from these obligations.
• Information relating to the expat is available at:
http://expat.sourceforge.net/
Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center, Ltd. and Clark
Cooper.
Permission is hereby granted, free of charge, to any person obtaining a copy of
this software and associated documentation files (the “Software”), to deal in the
Software without restriction, including without limitation the rights to use,
copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so, sub-
ject to the following conditions:
The above copyright notice and this permission notice shall be included in all
copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AU-
THORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAG-
ES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION
WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFT-
WARE.
NetBSD
1. Copyright Notice of NetBSD
For all users to use this product:
This product contains NetBSD operating system:
For the most part, the software constituting the NetBSD operating system is not
in the public domain; its authors retain their copyright.
The following text shows the copyright notice used for many of the NetBSD
source code. For exact copyright notice applicable for each of the files/binaries,
the source code tree must be consulted.
A full source code can be found at http://www.netbsd.org/.
Copyright © 1999, 2000 The NetBSD Foundation, Inc.
All rights reserved.

4
Redistribution and use in source and binary forms, with or without modifica-
tion, are permitted provided that the following conditions are met:
ARedistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
BRedistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
CAll advertising materials mentioning features or use of this software must
display the following acknowledgment:
This product includes software developed by The NetBSD Foundation, Inc.
and its contributors.
DNeither the name of The NetBSD Foundation nor the names of its contribu-
tors may be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND
CONTRIBUTORS ''AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DIS-
CLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEM-
PLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMIT-
ED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CON-
TRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTH-
ERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
2. Authors Name List
All product names mentioned herein are trademarks of their respective owners.
The following notices are required to satisfy the license terms of the software
that we have mentioned in this document:
• This product includes software developed by the University of California,
Berkeley and its contributors.
• This product includes software developed by Jonathan R. Stone for the NetB-
SD Project.
•Thisproductincludessoftwaredeveloped by the NetBSD Foundation, Inc.
and its contributors.
• This product includes software developed by Manuel Bouyer.
• This product includes software developed by Charles Hannum.
• This product includes software developed by Charles M. Hannum.
• This product includes software developed by Christopher G. Demetriou.
• This product includes software developed by TooLs GmbH.
• This product includes software developed by Terrence R. Lambert.
• This product includes software developed by Adam Glass and Charles Han-
num.
• This product includes software developed by Theo de Raadt.

5
• This product includes software developed by Jonathan Stone and Jason R.
Thorpe for the NetBSD Project.
• This product includes software developed by the University of California,
Lawrence Berkeley Laboratory and its contributors.
• This product includes software developed by Christos Zoulas.
• This product includes software developed by Christopher G. Demetriou for
the NetBSD Project.
• This product includes software developed by Paul Kranenburg.
• This product includes software developed by Adam Glass.
• This product includes software developed by Jonathan Stone.
• This product includes software developed by Jonathan Stone for the NetBSD
Project.
• This product includes software developed by Winning Strategies, Inc.
•Thisproductincludessoftwaredeveloped by Frank van der Linden for the
NetBSD Project.
• This product includes software developed for the NetBSD Project by Frank
van der Linden.
• This product includes software developed for the NetBSD Project by Jason R.
Thorpe.
• The software was developed by the University of California, Berkeley.
• This product includes software developed by Chris Provenzano, the Univer-
sity of California, Berkeley, and contributors.
Sablotron
Sablotron (Version 0.82) Copyright (c) 2000 Ginger Alliance Ltd. All Rights Re-
serve
a) The application software installed on this product includes the Sablotron soft-
ware Version 0.82 (hereinafter, “Sablotron 0.82”), with modifications made by
the product manufacturer. The original code of the Sablotron 0.82 is provided by
Ginger Alliance Ltd., the initial developer, and the modified code of the Sa-
blotron 0.82 has been derived from such original code provided by Ginger Alli-
ance Ltd.
b) The product manufacturer provides warranty and support to the application
software of this product including the Sablotron 0.82 as modified, and the prod-
uct manufacturer makes Ginger Alliance Ltd., the initial developer of the Sa-
blotron 0.82, free from these obligations.
c) The Sablotron 0.82 and the modifications thereof are made available under the
terms of Mozilla Public License Version 1.1 (hereinafter, “MPL 1.1”), and the ap-
plication software of this product constitutes the “Larger Work” as defined in
MPL 1.1. The application software of this product except for the Sablotron 0.82
as modified is licensed by the product manufacturer under separate agree-
ment(s).
d) The source code of the modified code of the Sablotron 0.82 is available at: ht-
tp://support-download.com/services/device/sablot/notice082.html.

6
e) The source code of the Sablotron software is available at: http://www.ginger-
all.com.
f) MPL 1.1 is available at: http://www.mozilla.org/MPL/MPL-1.1.html.
JPEG LIBRARY
• The software installed on this product is based in part on the work of the In-
dependent JPEG Group.
SASL
CMU libsasl
Tim Martin
Rob Earhart
Rob Siemborski
Copyright (c) 2001 Carnegie Mellon University. All rights reserved.
Redistribution and use in source and binary forms, with or without modifica-
tion, are permitted provided that the following conditions are met:
ARedistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
BRedistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
CThe name “Carnegie Mellon University” must not be used to endorse or pro-
mote products derived from this software without prior written permission.
For permission or any other legal details, please contact:
Office of Technology Transfer
Carnegie Mellon University
5000 Forbes Avenue
Pittsburgh, PA 15213-3890
[phone], fax: [phone]
[email protected]
DRedistributions of any form whatsoever must retain the following acknowl-
edgment:
“This product includes software developed by Computing Services at Carn-
egie Mellon University (http://www.cmu.edu/computing/).”
CARNEGIE MELLON UNIVERSITY DISCLAIMS ALL WARRANTIES WITH
REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL CARNEGIE
MELLON UNIVERSITY BE LIABLE FOR ANY SPECIAL, INDIRECT OR CON-
SEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING
FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF
CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT
OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS
SOFTWARE.

7
MD4
Copyright (C) 1990-2, RSA Data Security, Inc. All rights reserved.
License to copy and use this software is granted provided that it is identified as
the “RSA Data Security, Inc. MD4 Message-Digest Algorithm” in all material
mentioning or referencing this software or this function.
License is also granted to make and use derivative works provided that such
works are identified as “derived from the RSA Data Security, Inc. MD4 Message-
Digest Algorithm” in all material mentioning or referencing the derived work.
RSA Data Security, Inc. makes no representations concerning either the mer-
chantability of this software or the suitability of this software for any particular
purpose. It is provided “as is” without express or implied warranty of any kind.
These notices must be retained in any copies of any part of this documentation
and/or software.
MD5
Copyright (C) 1991-2, RSA Data Security, Inc. Created 1991. All rights reserved.
License to copy and use this software is granted provided that it is identified as
the “RSA Data Security, Inc. MD5 Message-Digest Algorithm” in all material
mentioning or referencing this software or this function.
License is also granted to make and use derivative works provided that such
works are identified as “derived from the RSA Data Security, Inc. MD5 Message-
Digest Algorithm” in all material mentioning or referencing the derived work.
RSA Data Security, Inc. makes no representations concerning either the mer-
chantability of this software or the suitability of this software for any particular
purpose. It is provided “as is” without express or implied warranty of any kind.
These notices must be retained in any copies of any part of this documentation
and/or software.