StandDesk Dual Motor Stand Desk User manual

DUAL MOTOR
ASSEMBLY
MANUAL
F2 - DM - TS

PARTS
HARDWARE
8. Handset 9. Power Cords x37. Control Box 11. Crossbar (optional)10. Cable Management Tray (optional)
1. Leg x2 6. Control Box Holder
2. Support Brace x2 4. Stabilizing
Foot Plate x2
5. Feet x2
3. Middle Slat x2
Allen Wrench Open Wrench ST3.5x19 x2 ST4.8x19 x6 M6x12 x22 M6x25 x4 M6x30 x4 M6x35 x8 Inserts x2 Washers x4
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS

!
!
!
!
!
!
!
!
Make sure there are no obstacles in the desk’s path. Make sure the desktop is not touching any walls.
Make sure all cords are the appropriate length in order to accommodate the change in height of your desk.
Keep children away from fully electric standing desks, control boxes, and controllers. There is a risk of injury or electric shock.
Keep all electrical components away from liquids.
Do not sit, stand, crawl or lie on or under the StandDesk Frame.
Do not place any objects taller than 20" underneath the StandDesk.
Do not open any of the components - Legs, Control Box, Controller. There is a risk of injury or electric shock.
This product is designed with a duty cycle of 10% (2 min. on & 18 min. off).
CAUTION / INFORMATION
TOOLS YOU MAY NEED
I
Philip’s Head Screwdriver Drill
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
VIDEO ASSEMBLY GUIDE
www.standdesk.co/pages/faq
5mm Allen Bit

STEP TWO
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
Attach the SUPPORT
BRACES to the outside
of each LEG using x4
M6x12 BOLTS.
x4 M6x12
IMPORTANT!
Place the Support Braces
on the DESK TOP so they
match up with the
pre-drilled holes in your top.
1MATCH THEM UP
1

STEP THREE
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
If the MIDDLE SLATS arrive
disassembled, slide the two
MIDDLE SLAT pieces over the U
shaped piece.
Place your MIDDLE SLATS on
your top with the bolt holes
facing up. Adjust the length of
the SLATS to match the width
of the LEGS by loosening the
bolts and pulling ends of the
SLATS apart.
Lightly secure the middle of
each MIDDLE SLAT in place
using x4 M6x30 BOLTS.
A.
B.
C.
A
B
C
x4 M6x30

STEP SIX
Place x1 STABILIZING FOOT
PLATE on top of each LEG.
Make sure the "lip" of the
PLATE is touching the LEG
and the smooth side is
facing up.
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
*
3
3
3MATCH THEM UP

STEP SEVEN
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
Place x1 FOOT on top of
each STABILIZING FOOT
PLATE with Black Pads on
the ends of the feet facing
up.
Attach each FOOT using x4
M6x12 BOLTS.
PRO TIP!
Install the bolts in a
diagonal pattern to ensure
all the holes are aligned
before fully tightening.
x8 M6x12
B.
4
4
4
MATCH THEM UP
4

STEP EIGHT
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
Remove the x2 PRE-INSTALLED
M6x35 BOLTS from the BACK
MIDDLE SLAT.
Attach the CABLE MANAGEMENT
TRAY to the BACK MIDDLE SLAT,
making sure the tray is facing the
back of your desk using x4 M6x12
BOLTS and x4 WASHERS to
attach.
Then reinstall the x2 M6x35
BOLTS onto the BACK SLAT.
x2 M6x35
x4 M6x12 x4 Washers
OPTIONAL UPGRADE - CABLE
MANAGEMENT TRAY
A.
B
B
A
5
5
5MATCH THEM UP

STEP NINE
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
Secure the CONTROL BOX
to the CONTROL BOX
HOLDER with x2 INSERTS.
Be sure to press the
INSERTS down firmly. The
screw head should be flush
with the rim of the
CONTROL BOX.
x2 INSERTS
A.
*

STEP TEN
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
Attach the CONTROL BOX
HOLDER to the FRONT
MIDDLE SLAT using x2
M6x12 BOLTS.
The CONTROL BOX HOLDER
should be situated in
between both MIDDLE
SLATS.
x2 M6x12
*
6
6
6
MATCH THEM UP

STEP FIVE
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
x2 ST3.5x19 x8 ST4.8x19
Use x6 ST4.8x19 SCREWS to
attach your SUPPORT BRACES to
your TOP.
Attach the HANDSET to the front
edge of the desk with x2 ST3.5x19
SCREWS.
If your desk does not have
pre-drilled holes you may have to
drill your own.
A.
B.
*
A
A
B

STEP ELEVEN
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
Connect the HANDSET
CORD, MOTOR CORDS,
and POWER CORD to the
CONTROL BOX .
Go back and ensure all
the screws and bolts are
fully tightened!
Then carefully flip your
desk.
Plug the desk into an
outlet and make sure
nothing is in its path.
A.
B.
C.
D.

STEP TWELVE
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
Extend the CROSSBAR to
match the width of the
LEGS by pulling both ends
away from eachother. Make
sure the bolt holes in the
middle of the CROSSBAR
are facing the feet.
Attach the CROSSBAR to
each LEG using 4 M6x25
BOLTS.
Secure the middle of the
CROSSBAR using x4 M6x12
BOLTS.
x4 M6x12
x4 M6x25
OPTIONAL ACCESSORY -
CROSSBAR
A.
B.
C. C
B
B

DUAL MOTOR ASSEMBLY MANUAL F2-SM-TS
PRESS
OR
AND HOLD
15-30 SEC
PRESS
AND HOLD
15-30 SEC
INITIALIZING YOUR STANDDESK
YOU MUST INITIALIZE YOUR STANDDESK BEFORE USE!
Press and hold the down arrow for 15-30 seconds.
As you hold the down arrow, the frame will go down to its lowest position and then calibrate.
Do not release arrow before calibration is successful.

MEMORY HANDSET
MANUAL
Seng OneSeng Two
Seng Three
Menu LED Display Up Arrow Down Arrow
HIT:
OH:
OLU:
GLP:
CON:
To wake press any buon.
Calibrate:
Wake:
Set
Preferred
Heights:
PRESS/HOLD
LED Display shows
15 seconds
HOLD until Display shows
RELEASE then Display shows 60.
CALIBRATION SUCCESSFUL
You must calibrate your desk
before proceeding with any other step.
ADJUST to 1st preferred height
PRESS
PRESS
REPEAT steps for remaining settings.
stands for HIT. This protects your desk against
collisions that could lead to damage.
if something hits your frames while it is raising or lowering,
it will automacally stop and Handset will read
stands for Overheat. This will show up if the desk
has had two minutes of constant usage. To resolve, wait
15 minutes for your desk to cool down.
stands for Overload, this means there is too much
weight on your frame. Either remove some weight or
change the load capacity on your frame in seng
stands for Go to Lowest Posion. This means your
desk must be rebalibrated.
stands for Connecon. One of the frame legs are
not working properly. Unplug the device and plug it back in.
ERROR MESSAGES
ESSENTIALS

MEMORY HANDSET
MANUAL (CONTINUED)
Seng OneSeng Two
Seng Three
Menu LED Display Up Arrow Down Arrow
Measurement
Conversion:
Collision
Sensivity:
Set
Max/Min
Load
Capacity:
PRESS/HOLD
PRESS
PRESS
PRESS
PRESS
PRESS
20 seconds
PRESS
LED Display will show
PRESS/HOLD 20 seconds
PRESS/HOLD 20 seconds
LED Display will show
LED Display will show
ADJUST max/min load capacity using
to exit or
PRESS to choose a dierent (P) setting
OR
OR
PRESS
PRESS to exit or
PRESS to choose a dierent (P) settingOR
PRESS OR
once to show
PRESS twice to show
to go from inches (1) and cm (0)
PRESS OR to adjust sensitivity (5-30)
then
then
15 is standard, low number = more sensitive.
ADVANCED SETTINGS

Position the LEGS so the
end with the motor is flush
with the DESK TOP and the
cords are pointing toward
one another.
The holes on the legs for
the OPTIONAL CROSSBAR
will be facing toward the
back of your desk.
STEP ONE
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
BACK
holes for
opt. Crossbar
A.
B.
A
A
B
Lay out all of the parts and
hardware to ensure you have
everything.
Assemble your frame on the
underside of your desk top.
To do this, make sure the top
is laying on a soft surface
such as carpet or towel with
the screw holes facing up.
This will help to avoid
scratching the top’s surface.
FRONT

STEP FOUR
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
Attach the MIDDLE SLATS
to the LEGS using x4
M6x35 BOLTS for each
MIDDLE SLAT then
tighten the bolts in the
middle of both slats.
IMPORTANT!
Make sure stickers 5and
6are pointing towards
the front of your desk.
This will help in a later
step.
x8 M6x35 2
2
6
5
2
2
2
2
MATCH THEM UP
Back Slat
5
Front Slat
6
6
5
FRONT