StandDesk Dual Motor Stand Desk User manual

DUAL MOTOR
ASSEMBLY
MANUAL
F2 - DM - TS

!
!
!
!
!
!
!
!
Make sure there are no obstacles in the desk’s path. Make sure the desktop is not touching any walls.
Make sure all cords are the appropriate length in order to accommodate the change in height of your desk.
Keep children away from fully electric standing desks, control boxes, and controllers. There is a risk of injury or electric shock.
Keep all electrical components away from liquids.
Do not sit, stand, crawl or lie on or under the StandDesk Frame.
Do not place any objects taller than 20" underneath the StandDesk.
Do not open any of the components - Legs, Control Box, Controller. There is a risk of injury or electric shock.
This product is designed with a duty cycle of 10% (2 min. on & 18 min. off).
CAUTION / INFORMATION
TOOLS YOU MAY NEED
I
Philip’s Head Screwdriver Drill
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
VIDEO ASSEMBLY GUIDE
www.standdesk.co/pages/faq
5mm Allen Bit

PARTS
HARDWARE
8. Handset 9. Power Cords x37. Control Box 11. Crossbar (optional)10. Cable Management Tray (optional)
1. Leg x2 6. Control Box Holder
2. Support Brace x2 4. Stabilizing
Foot Plate x2
5. Feet x2
3. Middle Slat x2
Allen Key Hex Key ST3.5x19 x2 ST4.8x19 x6 M6x12 x22 M6x25 x4 M6x30 x4 M6x35 x8 Inserts x2 Washers x4
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS

Position the LEGS so the
end with the motor is flush
with the DESK TOP and the
cords are pointing toward
one another.
The holes on the legs for
the OPTIONAL CROSSBAR
will be facing toward the
back of your desk.
STEP ONE
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
BACK
holes for
opt. Crossbar
A.
B.
A
A
B
Lay out all of the parts and
hardware to ensure you have
everything.
Assemble your frame on the
underside of your desk top.
To do this, make sure the top
is laying on a soft surface
such as carpet or towel with
the screw holes facing up.
This will help to avoid
scratching the top’s surface.

STEP TWO
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
Attach the SUPPORT
BRACES to the outside of
each LEG using x4 M6x12
BOLTS.
x4 M6x12
IMPORTANT!
Place the Support Braces
on the DESK TOP so they
match up with the
pre-drilled holes in your top.
A.

STEP THREE
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
x2 ST3.5x19 x8 ST4.8x19
Use x6 ST4.8x19 SCREWS to
attach your SUPPORT BRACES to
your TOP.
Attach the HANDSET to the front
edge of the desk with x2 ST3.5x19
SCREWS.
If your desk does not have
pre-drilled holes you may have to
drill your own.
A.
B.
*
A
A
B

STEP FOUR
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
If the MIDDLE SLATS arrive
disassembled, slide the two
MIDDLE SLAT pieces over
the Ushaped piece.
Place your MIDDLE SLATS
with the pre-installed bolts
facing up. Adjust the length
of the SLATS to match the
width of the LEGS by
loosening these bolts and
pulling the SLATS apart.
Attach the MIDDLE SLATS to
the LEGS using x4 M6x35
BOLTS for each MIDDLE
SLAT then tighten the bolts
in the middle of both slats.
x8 M6x35
A.
B.
C.
A
B
C
C
C
C

STEP FIVE
Place x1 STABILIZING FOOT
PLATE on top of each LEG.
Make sure the "lip" of the
PLATE is touching the LEG
and the smooth side is
facing up.
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
A.
*

STEP SIX
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
Place x1 FOOT on top of each
STABILIZING FOOT PLATE
with Black Pads on the ends
of the feet facing up.
Attach each FOOT using x4
M6x12 BOLTS.
PRO TIP!
Install the bolts in a diagonal
pattern to ensure all the
holes are aligned before fully
tightening.
x8 M6x12
A.
B.

STEP SEVEN
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
Remove the x2 PRE-INSTALLED
M6x35 BOLTS from the BACK
MIDDLE SLAT.
Attach the CABLE MANAGEMENT
TRAY to the BACK MIDDLE SLAT,
making sure the tray is facing the
back of your desk using x4 M6x12
BOLTS and x4 WASHERS to attach.
Then reinstall the x2 M6x35
BOLTS onto the BACK SLAT.
x2 M6x35
x4 M6x12 x4 Washers
OPTIONAL UPGRADE - CABLE
MANAGEMENT TRAY
A.
B.
B
B
A

STEP EIGHT
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
Secure the CONTROL BOX
to the CONTROL BOX
HOLDER with x2 INSERTS.
Be sure to press the
INSERTS down firmly. The
screw head should be flush
with the rim of the
CONTROL BOX.
x2 INSERTS
A.
*

STEP NINE
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
Attach the CONTROL BOX
HOLDER to the FRONT
MIDDLE SLAT using x2
M6x12 BOLTS.
The CONTROL BOX HOLDER
should be situated in
between both MIDDLE
SLATS.
x2 M6x12
A.
*

STEP TEN
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
Connect the HANDSET
CORD, MOTOR CORDS,
and POWER CORD to the
CONTROL BOX .
Go back and ensure all
the screws and bolts are
fully tightened!
Then carefully flip your
desk.
Plug the desk into an
outlet and make sure
nothing is in its path.
A.
B.
C.
D.

STEP ELEVEN
DUAL MOTOR ASSEMBLY MANUAL F2-DM-TS
Extend the CROSSBAR to
match the width of the
LEGS by loosening the two
middle bolts. These bolts
should be facing down.
Attach the CROSSBAR to
each LEG using 4 M6x25
BOLTS.
x4 M6 25
OPTIONAL ACCESSORY -
CROSSBAR
A.
B.
A
B
B

DUAL MOTOR ASSEMBLY MANUAL F2-SM-TS
PRESS
OR
AND HOLD
15-30 SEC
PRESS
AND HOLD
15-30 SEC
INITIALIZING YOUR STANDDESK
YOU MUST INITIALIZE YOUR STANDDESK BEFORE USE!
Press and hold the down arrow for 15-30 seconds.
As you hold the down arrow, the frame will go down to its lowest position and then calibrate.
Do not release arrow before calibration is successful.

HIT:
OH:
OLU:
GLP:
CON:
To wake press any buon.
Calibrate
or Reset:
Wake:
Set
Preferred
Heights:
MEMORY HANDSET
MANUAL
PRESS/HOLD LED Display shows15 seconds HOLD until Display shows RELEASE then Display shows 60.
ADJUST to 1st preferred height
PRESS PRESS REPEAT steps for remaining settings.
stands for HIT. This protects your desk against collisions that could lead to damage.
if something hits your frame while it is raising or lowering, it will automacally stop and Memory Handset will read
stands for Overheat. This will show up if the desk has had two minutes of constant usage. To resolve, wait 15 minutes for
your desk to cool down.
stands for Overload, this means there is too much weight on your frame. Either remove some weight or change the load
capacity on your frame in seng
stands for Go to Lowest Posion. This means your desk must be re-calibrated.
stands for Connecon. One of the frame legs are not working properly. Unplug the device and plug it back in.
Seng OneSeng Two
Seng Three
Menu LED Display Up Arrow Down Arrow

Measurement
Conversion:
Collision
Sensivity:
Set Max
Height:
Set Min
Height:
Set Max/Min
Load Capacity:
MEMORY HANDSET
MANUAL (CONTINUED)
PRESS/HOLD 15 seconds RELEASE WHEN LED Display blinks PRESS/HOLD
When desk raises to highest point (120 CM) RELEASE PRESS LED Display shows
PRESS/HOLD 15 seconds
PRESS/HOLD PRESS
PRESS
PRESS
PRESS
PRESS
20 seconds
RELEASE WHEN LED Display blinks PRESS/HOLD
When desk reaches lowest point RELEASE PRESS
PRESS
LED Display shows
LED Display will show
PRESS/HOLD 20 seconds
PRESS/HOLD 20 seconds
LED Display will show
LED Display will show
ADJUST max/min load capacity using
to exit or PRESS to choose a dierent (P) setting
OR
OR
PRESS
PRESS to exit or
PRESS to choose a dierent (P) settingOR
PRESS OR
once to show
PRESS twice to show
to go from inches (1) and cm (0)
PRESS OR to adjust sensitivity (5-30)
then
then
15 is standard, lower the number the more sensitive.
Seng OneSeng Two
Seng Three
Menu LED Display Up Arrow Down Arrow