StandDesk SIMPLE User manual

ASSEMBLY MANUAL
Single Motor Dual Segment Frame
SIMPLE 2017

This StandDesk is height adjustable so that it can be positioned at the most
ergonomically suitable height. Any other use is at your risk.
Under no circumstances does StandDesk accept warranty claims or liability claims
for damages caused from improper use or handling of the desk frame.
USE / LIABILITY
!!
!!
Make sure no obstacles
around you are in the desk’s
path. Make sure the desktop is
not touching any walls. Make
sure all cords are appropriate
length to accommodate the
change in height.
!! Keep children away from electric height-adjustable desks,
control units and handsets. There is a risk of injury and
electric shock.
Keep all electrical components away from liquids.
Do not open any of the components - the Legs, Control Box,
or Handset. There is a danger of electric shock.
!! Do not sit, stand, crawl, or lie on or under the StandDesk.
!!
!!
This product is designed with a duty cycle of 10%
(2 min. on, 18 min. off)
In the event of a power outage or if the power cord is
unplugged, a manual reset may be necessary.
Do not place any object taller than 20” underneath the
StandDesk
CAUTION/INFORMATION
Pinch Point
Keep hands and
fingers clear
!WARNING

WATCH ASSEMBLY VIDEO
www.standdesk.co/pages/faq
CLICK ON
StandDesk Simple Assembly
!
HIGHLY RECOMMENDED

STICKER SYSTEM
Your desk might not have the sticker system to match up and
align parts. But not to worry, the assembly process is just the
same.
Now we’re ready to get familiar with all the pieces.
If you have the stickers, make sure their color and number
match up, like so.
1
PERFECT MATCH

Open WrenchAllen Wrench (x2)
TOOLS
TOOLS REQUIRED
4mm Hex Bit (Optional)Phillips Head Screwdriver Power Drill (Optional) Tape Measure
COMPONENTS
Stabilizing Foot Plates (x2)
Power Cords (x2)
Leg without Motor Leg with Motor Support Braces (x2) Back Middle Slat
Front Middle Slat
Standard Handset
(REPLACES STANDARD HANDSET IF ORDERED)
Memory Handset
Drive Shaft plus Rod Feet (x2)
Cable Management Tray Crossbar
HARDWARE
M5x5 (x4)
M6x25 (x6)
Washers (x4)
ST3.5x19 (x2)
M6x12 (x12)
ST4.8x19 (x8)
M6x16 (x10)
M6x55 (x4)
P1
P5
P11
H2 H3
H4
H8
H5 H6
H9 H10
H7
H11
P12 P13 P14
P6 P7 P8
P9
P2 P3 P4
Control Box
P10
Drive Shaft Tool
H1
OPTIONAL UPGRADES

PARTS DIAGRAM
Height Range
Base Width
Travel Speed
Weight Capacity
Duty Cycle
Specifications
26.4 in (67 cm) - 46 in (117 cm)
43 in (109 cm) - 58 in (147 cm)
1.01 in/sec (2.57 cm/sec)
308.6 lbs (140 kgs)
10% max. 2 mins on, 18 mins off
Soft start/stop
Adjustable leveling studs
No.
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
Component Name
Leg without Motor
Leg with Motor
Support Braces
Back Middle Slat
Front Middle Slat
Drive Shaft plus Rod
Feet
Stabilizing Foot Plates
Power Cords
Control Box
Standard Handset
Qty
1
1
2
1
1
1
2
2
2
1
1
No.
H5
H6
H7
H8
H9
H10
H11
Component Name
ST 3.5 x 19 Screws
ST 4.8 x 19 Screws
M5 x 5 Bolts
M6 x 12 Bolts
M6 x 16 Bolts
M6 x 25 Bolts
M6 x 55 Bolts
Qty
2
8
4
12
10
6
4
P1
P2
P3
P4
P5
P8
P7
P6
P9
H7
H8
H11
H9
H10
H9

STEP 2
Place the legs upside down on the underside of your desktop.
Ensure the leg with motor is facing towards the front of your
desk, where you’ll be standing.
FRONT
STEP 1 IMPORTANT
Start with the leg with motor. Use the drive shaft tool to push the
short motor rod that’s sticking out in toward the motor and all
the way through until it stops.
Crossbar
plates facing BACK

STEP 3
Attach the support braces to each leg using four M6x12 bolts.
Ensure the flat side is touching the desktop.
H8
1
1
1
!
Match up the triangles so they kiss
If you’re using a StandDesk top, place the support braces
on the desk so they line up with the pre-drilled holes. It’ll
make it easier for you later on.
PRO TIP

STEP 5
Attach the back middle slat using four M6x55 bolts. If you are
using a medium or large top, you will need to extend the width of
the middle slats.
H11
2
STEP 4
Find the front and back middle slats. Loosen but don’t remove
any pre-installed M6x12 bolts. Here’s what the two slats look like
in case they’re disassembled.
ASSEMBLED
BACK
FRONT
DISASSEMBLED
The middle slat bolts may or may not be pre-installed.
! !

Slide the thin part of the front middle slat underneath the motor
and attach to the leg using two M6x16 bolts.
H9
2
STEP 7
Attach the opposite end of the front middle slat with two M6x25
bolts.
H10
2
STEP 6

Now it’s time to connect the two legs with the drive shaft. Start
by removing the inner rod completely from the white drive shaft.
DRIVE SHAFT INNER ROD
STEP 9
Attach the white drive shaft to the leg with motor by sliding it
over the motor rod.
STEP 8

STEP 11
Continue to push the inner rod through, using the drive shaft tool
until it stops.
Carefully thread the inner rod through the leg without a motor. Be
gentle and use two fingers to align.
STEP 10

STEP 12
Now that the inner rod is in the white drive shaft, adjust the drive
shaft so it’s 1/2 inch off the motor.
!1/2”
STEP 13
Secure the white drive shaft to the inner rod using two M5x5
bolts.
H7

STEP 14
Place the stabilizing foot plates on top of each leg.
3
STEP 15
Place the feet on top of the stabilizing foot plates and align the
holes. Finger tighten four M6x16 bolts in a diagonal pattern for
best fit. Once all bolts are aligned, fully screw them in.
4
H9

If you purchased the optional crossbar, assemble it by loosening
the pre-installed bolts in the middle of the crossbar. Then, adjust
the width.
ASSEMBLED
! ! ! !
DISASSEMBLED
STEP 17 OPTIONAL UPGRADE
If you purchased the optional cable management tray, attach it
face down to the back middle slat using four M6x12 bolts and
washers.
STEP 16 OPTIONAL UPGRADE
5
H8
H3
M6x30 BOLTS
BACK
MIDDLE
SLAT FRONT
MIDDLE
SLAT

STEP 19
Attach the frame to the top using six ST 4.8x19 screws.
H6
Ensure that the raised bolt holes are facing out. Attach the
crossbar to the holes on the back of the legs using four M6x25
bolts. Tighten the middle bolts once done.
H10
STEP 18 OPTIONAL UPGRADE

STEP 20
Attach the control box to the middle of the top using two
ST 4.8x19 screws. It can also sit on the cable management tray
if you upgraded to one.
H6
If your top does not have pre-drilled holes, you can use a
drill or a power tool to attach your top. Here’s a separate
video to help you out.
http://bit.ly/standdesktop
PRO TIP

STEP 22
Connect the handset cord and extension cord to the front side of
the control box. Connect the power cord to the back.
FRONT BACK
STEP 21
Attach the handset to the top using two ST 3.5x19 screws.
Attach the remaining M5x5 bolts to the drive shaft.
H5

STEP 24
Be sure to tighten all the bolts. Carefully flip the desk over onto
the feet. Flip the desk over by raising the front side up first, so
you don’t damage the handset.
STEP 23
Use the extension cord to connect the leg with motor and
control box.
!MIND THE HANDSET

STEP 25
Almost there. Plug in your very own StandDesk!
Finally, it’s time to turn the desk on by holding the down button
until it reaches the lowest position. If you have a memory
handset, it will say for SUCCESS.
We have two kinds of handsets, but the same instructions apply.
DON’T FORGETSTEP 26
A B