StarDental Titan S User manual

Titan S:
Tube Assembly, Gasket, Retainer Ring, (2/3-Line)..........................256454
Tube Assembly, Gasket (4-Line) .............................................................256455
Instruction Manual
Titan®Blis-Sonic Scaler SW/S
Replacement Assemblies and Spare Kits
WARNING: Never remove scaler housing with tip assembled to the scaler.
1. Unthread the front of the scaler housing to expose the front suspension carrier.
2. Remove the two old O-rings and install the replacement O-rings, StarDental Part #256718.
3. Re thread front of scaler housing to original position.
Titan S/SW Rear Seal & Swivel O-Rings
O-Rings & Rear Seal Replacement
Swivel O-Rings: Periodically replace the swivel
O-rings, StarDental®Part #259884.
Front Suspension O-Rings: After two years, front
suspension O-rings relax resulting in play between
shaft and handle.
Swivel O-Rings
Front Suspension O-Rings
Front of Scaler Housing
Seals wear with repeated use. Replace rear seals
annually or as needed. On either the
2/3-line swivel or Titan S 2/3-line Scaler replace
the 2/3-line rear seal with StarDental Part #203103.
On either the 4-line swivel or Titan S 4-line Scaler
replace seal with StarDental Part #202897.
Rear Seal on
the Swivel
Rear Seal on
the 4-line
Titan S
2/3-line for Titan S/SW
1. Remove 2/3-line rear seal with an
explorer.
2. Place new rear seal over drive air and
water tubes.
3. Carefully push seal into place using a
blunt instrument. Rear Seal
Titan S 2/3-line
Titan SW
2/3-line
Rear Seal
Swivel
Cleaning Wire
CLEANING the Tips
Clean tips weekly by running cleaning wire, StarDental Part #256719, through entire tip starting at
opening in front.
CLEANING Titan SW or S Water Tube
On a regular basis or if a water tube blockage occurs,
remove the tip, and on the Titan SW also disconnect the
swivel. Push the cleaning wire through the internal water
tube using needle nose pliers at the front on both the Titan
SW and S as shown. Push small lengths of 3 to 4 mm at a
time until the wire emerges at the opposite end. Pull wire
completely out.
Cleaning Wire
Opening
Front - Titan K and SW
StarDental® Instruments

Cleaning Wire (cont.)
CLEANING the Swivel
1. Disconnect swivel from scaler and tubing. Depress foot control; verify that water exits tubing.
2.Connectswiveltotubing.Depressfootcontrol;ifalmost nowaterexitsfront of swivel,clean asfollows.
3. Detach swivel from tubing and nd water tube.
4. Insert wire throughout water tube and move wire back and forth to loosen debris at blockage.
5. Remove wire and apply a blast of syringe air into water tube.
Note: To insure peak performance and proper functioning of scaler, clean swivel and mating com-
ponents daily or as needed. Do not attempt to disassemble swivel.
Insert
Wire
Water Tube
StarDental®
1816 Colonial Village Lane
Lancaster, PA 17601 U.S.A.
Printed in the U.S.A.
©2019 DentalEZ, Inc.
60532 D
For new products, manuals and technical
information, call 1-866-DTE-INFO
or visit our web site @www.dentalez.com
StarDental® Instruments
Replace the washer gasket or o-ring on the Blis-sonic K water tube assembly annually with the gasket provided in the StarDental Spares Kit
#256888 for the 2/3-line, or the o-ring provided in the StarDental Spares Kit #264592 for the 4-line.
Water Tube Gasket Replacement
1. Remove the water tube assembly. Remove rear seal with an old dental instrument
such as an explorer. Gently tug on the air tube with needle nose pliers to remove
water tube assembly. Retaining ring pops out when removing assembly. Take care
not to lose retaining ring.
2. Slide old gasket off water tube.
3. Slide on new gasket and seat in place.
4. Insert water tube into handle, rotate slowly between thumb and forenger to locate
internal water tube assembly. Push lightly to fully seat tube.
Note: Reinstall retaining ring. Then assemble rear seal over tubes and retaining ring.
Use needle nose pliers carefully to prevent distortion of the air tube
when removing water tube assembly.
O-Ring
Rear Seal
Unthread
Water Tube Assembly
Water Tube
Water
Manifold
4-Line
2/3 Line:
1. Remove rear seal. Then, using a 7/16” open end wrench, or an adjustable wrench,
unthread manifold assembly (water tube assembly).
2. Slide old o-ring off of water tube.
3. Slide on new o-ring and seat in place.
4. Insert water tube into handle, rotate slowly between thumb and forenger to locate
internal water tube assembly. Thread manifold assembly (water tube assembly) into
torque reaction sleeve. Tighten using 7/16” open end wrench, or adjustable wrench.
Note: Reinstall rear seal.
4 Line:
NOTICE
Water
Tube
Plate
Retaining
Ring
Gasket
2/3-line
Water Tube
Assembly
Water
Manifold