StarDental DentalEZ Titan User manual

Contents
Specications
• Specications
•Installation - Swivel Motors
•Installation - Non Swivel Motors
• Operation
• Cleaning
• Sterilization
5,000 rpm Motor: Titan®3 (StarDental®Part #262261); Titan 3 For use with Extended Straight Attachment
(ESA) (StarDental®Part #265208); Titan 3 Fixed Back End (StarDental Part #262409); or
Titan T (StarDentalPart #263940)
20,000 rpm Motor: Titan 3 (StarDental Part #262262); Titan 3 Fixed Back End (StarDental Part 262410); or
Titan T (StarDental Part #263941)
• No Lubrication Required
• Recommended Air Pressure: 40-45 psi (swivel motor)
• Air Flow: 2.1 SCFM @ 40-45 psi at Maximum Power Point (swivel motor)
• Rotation: Forward and Reverse
• 4-Line Connection (Fixed Back End)
Installation - Swivel Motors
1. Select the motor appropriate for tubing based on power requirements. Examine connection of the motor and
swivel tubing conguration as these must match conguration of delivery system tubing.
Drive Air Water
Exhaust Air Air
4-Line Tubing 2/3-Line Tubing
Drive Air
Water
2. Disconnect swivel from motor if necessary. Grasp the swivel in front of the bearing assembly between the
thumb and index nger as shown.
3. Slide tubing coupler until the end of the ISO connector is exposed; hold in hand as shown with ngers
securing the tubing.
4. Align and insert swivel tubes into the ISO connector holes.
5. While applying slight pressure to hold ttings in the connector holes, slide coupler forward and engage
threads. Continue threading coupler clockwise until hand tight against the swivel.
Swivel
Bearing Assembly
ISO Connector
Tubing
Coupler
Tubing
6. Using the wrench as shown, tighten the swivel to the tubing coupler. Be sure to turn tubing coupler, not swivel.
DO NOT OVER TIGHTEN.
Wrench Tubing
Coupler Turn Coupler While Holding
Swivel in Place
Note: This joint loosens over time, resulting in air leakage and loss of power. Check for tightness periodically.
7. Connect motor to swivel.
Operation
The 120° rotation speed adjustment ring sets direction and speed. To run motor forward at full speed, rotate ring towards
the letter ‘F’ while operating the foot control. Rotate to the letter ‘R’ to yield full speed in reverse. Vary speed by rotating ring
in either direction towards center. Note the small depression for the current setting. After setting, the motor runs at current
speed and direction until reset. Pausing the motor is not needed to alter direction or speed using the ring.
20,000 rpm - Lube Free
Made in the U.S.A.
JXXXXX
®
Titan 3
StarDental
®
Small Depression
120° Rotation Speed
Adjustment Ring
• Application Guide
• Troubleshooting
• Replacement Part Numbers
• Warranty
®
Titan 3
5,000 rpm - Lube Free
Made in theU.S.A.
JXXXXX
StarDental
®
Titan 3
20,000 rpm - Lube Free
Made in the U.S.A.
JXXXXX
®
StarDental
®
5K Motor
20K Motor
Swivel
Drive Gear
Installation - Non Swivel Motors
Note: If delivery unit has oil/mist lubrication, detach and drain; motor needs no lubrication.
NOTICE To prevent damage to bearings, before installing always check drive air pressure by using air pressure
gauge, StarDental Part #262591 (4/6-Line) between motor and tubing and obtain a reading. Adjust air pressure
at delivery head until gauge reads 40-45 psi while operating motor in full forward postion and with foot control
completely depressed.
1. Examine rear end connector of motor. Verify motor matches tubing connector of delivery system.
2. To connect motor to tubing, align drive air and exhaust tubes with mating ISO connector holes in coupler.
3. While applying slight pressure to hold tubing in connector holes, slide tubing coupler forward and engage
threads. Continue threading tubing coupler clockwise until hand tight against the motor. DO NOT OVER TIGHTEN.
Note: This joint loosens over time, resulting in air leakage and loss of power. Check for tightness periodically.
®
Titan 3
5,000 rpm- Lube Free
Made inthe U.S.A.
JXXXXX
StarDental
®
Titan 3
20,000 rpm - Lube Free
Made inthe U.S.A.
JXXXXX
R
StarDental
Instruments
®
Direction & Speed
Control Ring
Drive
Gear
Rear End Connector
5K Motor
(StarDental® Part #262409)
Drive
Gear
20K Motor
(StarDental® Part #262410)
Sterilizable up to 135°C
135°C
866.DTE.INFO (383.4636)
www.DentalEZ.com
0344
StarDental® 1816 Colonial Village Lane Lancaster, PA 17601 U.S.A. Printed in the U.S.A.
©2019 DentalEZ, Inc.
Emergo Europe
Prinsessegracht 20
2514 AP The Hague
The Netherlands
EC REP
StarDental® Instruments
Caution: Federal law restricts this device to sale by or on the order of a dentist.
062283 P Date of Issue 2019-05-24
Titan® Low-Speed Handpiece Motor Instruction Manual
Non-Sterile
Medical Device
Indications For Use
BEFORE OPERATING THE MOTOR, CAREFULLY READ AND FOLLOW ALL OF THESE INSTRUCTIONS. SAVE
THESE INSTRUCTIONS FOR FUTURE REFERENCE AND OBSERVE ALL WARNINGS AND CAUTIONS.
The Titan 5K and 20K low speed dental motors are used by trained dental professionals to facilitate various
dental procedures requiring cutting, drilling, polishing and pin setting.
Note: If delivery unit has oil/mist lubrication, detach and drain; motor needs no lubrication.
NOTICE To prevent damage to bearings, before installing always check drive air pressure by using air pressure
gauge, StarDental Part #262591 (4/6-Line) between swivel and tubing and obtain a reading. Adjust air pressure
at delivery head until gauge reads 40-45 psi while operating motor in full forward position and with foot control
completely depressed.
Cleaning & Sterilization
CAUTION
INSTRUCTIONS
6WDU 7LWDQ 
USP/XEH)UHH
0DGHLQWKH86$
-;;;;;
5
5
StarDental® Instrument Solutions
Drive Air
Red Tip
Applicator
Maintenance &Lubrication: The Titan Motor is LubeFree and, therefore, requires no lubrication.
However, at times debris from the delivery system’s drive air tubing collects in the motor. This build-up may cause
sluggish motor operation. To ease, place 3 drops of DentaLube II, StarDental Part #262539 into the drive air tube of
motor, and alternately operate the motor in forward and reverse.
Motor should be routinely maintained, checked for corrosion, worn parts, etc. and should be replaced on an as needed basis.
WARNING
Do not exceed 135°C
Do not use:
Limits on Reprocessing Repeated processing has minimal effect on these attachments. End of life is normally determined by wear and
damage due to use.
The handpiece motor must be cleaned and sterilized before rst use and between patient use.
Star Titan 3
20,000 rpm - Lube Free
Made in the U.S.A.
JXXXXX
RR
Internal
Surfaces
Swivel Bearing/
Spring Assembly
Clean
Cleaning-Manual: Cleaning the Swivel &Mating Motor Part: To optimize operation of the swivel connector, clean all internal surfaces of the
motor with a cotton swab soaked in isopropyl alcohol until clean. Clean area around bearing/spring assembly at rear of
swivel using isopropyl alcohol and a toothbrush. Dry both
using syringe air.
Sterilizing Handpiece Motor: After each patient, ush
air by running handpiece motor for 20 seconds.
Remove attachment. Clean all internal surfaces at rear
of handpiece motor with a cotton swab soaked in
isopropyl alcohol until clean. Clean all external surfaces
using a small toothbrush with isopropyl alcohol. Dry
thoroughly. Place handpiece motor and swivel in
sterilization bag – . Follow the sterilization guidelines as
stated by the manufacturer of your sterilizer.
Cleaning-Automated: Washer-disinfectors are not recommended.
Wrapped Instrument
Sterilization:
Gravity Type Autoclave: Pre-Vacuum Autoclave:
• Minimum of 15 minutes at 132° C • Minimum of 4 minutes at 132° C
• Minimum of 30 minutes at 121° C
Do not exceed 135° C
• dry heat sterilizer
•immersion techniques
• cold sterilizers • ultrasonic cleaners
• sterilizer bags containing disinfectants • hand soaps
• detergents
• chemical disinfectors
•surface sprays • surgical milk • surface wipes
Additional Information: Do not exceed the sterilizer manufacturer’s guidelines for load capacity. Use only paper or paper/plastic bags.
Storage: Store in bag after sterilization until ready to use.
Dry the motor for 30 minutes minimum using the sterilization dry cycle and allow the motor to cool to room
temperature in bag prior to use. If moisture is present, increase your sterilizer dry cycle appropriately.
Drying:
Containmentandtransportation: It is recommended that handpieces are reprocessed as soon as is reasonably practical following use.
Preparation for cleaning: Remove motor from swivel if applicable or tubing.
Use steam sterilization exclusively for complete sterility as outlined below.
Disinfection:
See Installation, Operating Recommendations, and/or Troubleshooting sections of this manual.Inspection & function testing:
Single: A standard sterilization packaging material must be used. Ensure that the pack is large enough to contain the
item without stressing the seals.
Packaging:
Manufacturer Contact: See rst or last panels of this manual.
It is the responsibility of the user to use only FDA compliant sterilizing equipment and accessories that are capable of
meeting the manufacturers recommendations below.
CAUTION
NOTICE Any serious incident occurring from the use of this device should be reported to StarDental immediately.
If incident occurred in a EU Member State the competent authority must be notied.

Always insist on StarDental parts for best performance.
Replacement Part Numbers
Titan 3 Titan T
Description Item Number Item Number
Troubleshooting
Problem: LACK OF POWER
Cause: Air pressure
Correction: Verify proper motor air pressure. Refer to applicable Installation section.
Cause: Crimped tubing
Correction: Straighten tubing inside and outside delivery head.
Cause: Swivel or Fixed Back End Motor not threaded fully onto tubing
Correction: Refer to applicable Installation section.
Cause: Brittle swivel or Fixed Back End Motor silicone rubber seal
Correction: Replace silicone rubber seal for 2/3-line swivel with StarDental® Part #203103
and 4-line with StarDental Part #202897.
Cause: Swivel O-rings worn
Correction: Replace swivel O-rings, StarDental Part #259884.
Cause: Debris build-up in motor or attachment
Correction: Clean motor and attachment. Refer to Cleaning section in this manual and
applicable attachment's manual(s).
Problem: SWIVEL WILL NOT DISENGAGE FROM MOTOR
Cause: Build-up of debris
Correction: Place 3 drops of DentaLube II, StarDental Part #262539, into the swivel/tubing
connector. Rotate swivel to circulate lubricant. Disengage motor. Contact dealer
if unable to disengage swivel. To prevent reoccurrence, refer to Cleaning.
Straight Nose Cone ..................................................................................................................................257506 ..................................................................263942
Motor-to-Angle Adapter ........................................................................................................................264073 ..................................................................263970
Torque Multiplier .....................................................................................................................................258443 ................................................................. 263944
Swivel, Motor 2/3-Line...........................................................................................................................260152 ..................................................................260152
Swivel, Motor 4-Line ...............................................................................................................................260144 ..................................................................260144
LubeFree Ball Bearing Auto Latch Angle .........................................................................................264146 ................................................................. 263950
LubeFree Ball Bearing Manual Latch Angle ...................................................................................262738 ................................................................. 263948
LubeFree Ball Bearing Autochuck Friction Grip Angle ..............................................................264151 ................................................................. 263954
LubeFree Ball Bearing Manual Chuck Friction Grip Angle .......................................................262740
LubeFree 5 Star Prophy Angle .............................................................................................................265801
Ball Bearing Auto Latch Angle .............................................................................................................264182
Ball Bearing Manual Latch ....................................................................................................................259005 ..................................................................263947
Ball Bearing Autochuck Friction Grip Angle ..................................................................................264149
Ball Bearing Manual Chuck Friction Grip Angle ...........................................................................258965 .................................................................263952
Titan Endodontic Angle, Auto Latch .................................................................................................262570 ..................................................................262570
Titan Endodontic Angle, Manual Latch ...........................................................................................262571 .................................................................. 262571
Air Pressure Gauge for 4/6-Line ........................................................................................................262591 ..................................................................262591
Silicone Rubber Seal, 2/3-Line (Pkg. of 3) ......................................................................................203103 .................................................................. 203103
Silicone Rubber Seal, 4-Line (Pkg. of 3) ..........................................................................................202897 ..................................................................202897
Swivel O-Rings Kit (2 large, 2 small) .................................................................................................259884 ................................................................. 259884
DentaLube II .............................................................................................................................................262539 ..................................................................262539
Titan T 20K, 4 Line, Stainless Steel Back End, Motor .................................................................................................................................................. 264430
Titan 3 5K Motor - Used with Extended Straight Attachment (ESA) .....................................265208
For new products, manuals and technical information, call 1-866-DTE-INFO or visit our web site at
www.dentalez.com.
Note: If a problem persists, contact dealer for further assistance or contact StarDental technical service at
1-866-DTE-INFO.
Lubricated LubeFree Lubricated LubeFree
CARIES REMOVAL
Systems Conguration Options:
5,000 RPM Motor 262261 263940
RPM Range: 2,000 to 5,000
Motor-to-Angle Adapter 264073 263970
Ball Bearing Friction Grip Angle OR 258965 262740 263952 263955
Ball Bearing Autochuck Friction Grip Angle 264149 264151 263953 263954
Ball Bearing Latch Angle OR 259005 262738 263947 263948
Ball Bearing Auto Latch Angle 264182 264146 263949 263950
20,000 RPM Motor 262262 263941
RPM Range: 2,000 to 5,000
Torque Multiplier 258443 263944
Motor-to-Angle Adapter 264073 263970
Ball Bearing Friction Grip Angle OR 258965 262740 263952 263955
Ball Bearing Autochuck Friction Grip Angle 264149 264151 263953 263954
Ball Bearing Latch Angle OR 259005 262738 263947 263948
Ball Bearing Auto Latch Angle 264182 264146 263949 263950
FINISHING (Cavity and crown preps)
RPM Range: 10,000 to 20,000
Systems Conguration Options:
20,000 RPM Motor 262262 263941
Motor-to-Angle Adapter 264073 263970
Ball Bearing Friction Grip Angle OR 258965 262740 263952 263955
Ball Bearing Autochuck Friction Grip Angle 264149 264151 263953 263954
Ball Bearing Latch Angle OR 259005 262738 263947 263948
Ball Bearing Auto Latch Angle 264182 264146 263949 263950
POLISHING
(Amalgam, composites, gold margins)
RPM Range: 10,000 to 20,000
Systems Conguration Options:
20,000 RPM Motor 262262 263941
Motor-to-Angle Adapter 264073 263970
Ball Bearing Latch Angle OR 259005 262738 263947 263948
Ball Bearing Auto Latch Angle 264182 264146 263949 263950
Application Guide Titan®3 Titan TTM Application Guide, con't. Titan®3 Titan TTM
Important Notice About Returning Product To The DentalEZ Inc.
Anyone wishing to return any DentalEZ Inc. product to a DentalEZ facility MUST obtain the proper RETURN AUTHORIZATION NUMBER
from the Customer Service Department. The RA Number must appear clearly marked on both the outside and inside of the returned
product carton. When calling for a return authorization number you will be asked to provide the following information:
To Obtain A
Return Authorization
Number Call
1-866-DTE-INFO
Items will be evaluated. Return Authorization Number is not a guarantee for credit. Your cooperation with this procedure will help us
expedite processing of any returns.
• Product Name, Model Number or Part Number
• Serial Number of Product
• Dealer Return Purchase Order Number
• Reason For Return
• Copy of Invoice Showing Purchase
PROPHY Lubricated LubeFree Lubricated LubeFree
RPM Range: 1,000 to 3,000
Systems Conguration Options:
5,000 RPM Motor 262261 263940
Motor-to-Angle Adapter 264073 263970
5 Star Prophy Angle 265803 265801 265802
20,000 RPM Motor 262262 263941
Torque Multiplier 258443 263944
Motor-to-Angle Adapter 264073 263970
5 Star Prophy Angle 265803 265801 265802
GRINDING & TRIMMING (Fabrication)
RPM Range: 10,000 to 20,000
Systems Conguration Options:
20,000 RPM Motor 262262 263941
Straight Nose Cone 257506 263942
POST & PIN DRILLING
Systems Conguration Options:
5,000 RPM Motor 262261 263940
RPM Range: 1,000 to 5,000
Motor-to-Angle Adapter 264073 263970
Ball Bearing Latch Angle OR 259005 262738 263947 263948
Ball Bearing Auto Latch Angle 264182 264146 263949 263950
20,000 RPM Motor 262262 263941
RPM Range: 1,000 to 5,000
Torque Multiplier 258443 263944
Motor-to-Angle Adapter 264073 263970
Ball Bearing Latch Angle OR 259005 262738 263947 263948
Ball Bearing Auto Latch Angle 264182 264146 263949 263950
PIN SETTING
Systems Conguration Options:
5,000 RPM Motor 262261 263940
RPM Range: 1,000 to 5,000
Motor-to-Angle Adapter 264073 263970
Ball Bearing Latch Angle OR 259005 262738 263947 263948
Ball Bearing Auto Latch Angle 264182 264146 263949 263950
20,000 RPM Motor 262262 263941
RPM Range: 500 to 2,000
Motor-to-Angle Adapter 264073 263970
10:1 Gear Reduction Latch Angle 264180 263951
20,000 RPM Motor 262262 263941
RPM Range: 500
Torque Multiplier 258443 263944
Motor-to-Angle Adapter 264073 263970
10:1 Gear Reduction Latch Angle 264180 263951
ENDODONTIC (Canal enlargements)
Systems Conguration Options:
20,000 RPM Motor 262262 263941
RPM Range: 500 to 2,000
Motor-to-Angle Adapter 264073 263970
10:1 Gear Reduction Latch Angle 264180 263951
5,000 RPM Motor 262261 263940
RPM Range: 350 to 5,000
Motor-to-Angle Adapter 264073 263970
Auto Latch Endodontic Angle - 262570
-for Standard Files & Reamers
(90° reciprocating motion) OR
Manual Latch Endodontic Angle - 262571
-for Latch Type Files & Reamers
(90° reciprocating motion)
ENDODONTIC (Condensing gutta percha)
RPM Range: 10,000 to 20,000
Systems Conguration Options:
20,000 RPM Motor 262262 263941
Motor-to-Angle Adapter 264073 263970
Ball Bearing Latch Angle OR 259005 262738 263947 263948
Ball Bearing Auto Latch Angle 264182 264146 263949 263950
Limited Warranty
O-Rings and Seals are specically excluded from this warranty.
DentalEZ® warrants the Titan
® Low Speed Handpiece Motor for 1 year from the date of purchase*.
Please note the following additional terms of our warranty policy:
• Warranties cover manufacturing defects only and do not cover defects resulting from abuse, improper handling, cleaning,
care or maintenance, normal wear and tear or non-observance of operating, maintenance or installation instructions. Failure
to use authorized parts or an authorized repair facility voids this warranty.
• Liability is limited to repair or replacement of the defective product at our sole discretion. All other liabilities, in
particular liability for damages, including, without limitation, consequential or incidental damages are excluded.
• THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. NO EMPLOYEE, REPRESENTATIVE OR DEALER IS AUTHORIZED
TO CHANGE THIS WARRANTY IN ANY WAY OR TO GRANT ANY OTHER WARRANTY.
*Provided conditions in warranty are met.
WARRANTY REGISTRATION
PLEASE VISIT THE WEBSITE BELOW TO REGISTER YOUR STARDENTAL PRODUCT. THIS WILL
ENSURE PROPER REGISTRATION AND PROMPT AND ACCURATE SERVICE SHOULD ANY OF YOUR
PURCHASES NEED EVALUATION OR REPAIR DURING THE WARRANTY PERIOD.
StarDental® Products: www.dentalez.com/warranty