Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a 3-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com
Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
Regulatory Compliance
FCC - Part 15
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Installation
Side A Ports
1. If you have a Windows computer with Internet access, connect the Built-in USB-C
Host Cable on the Multiport Adapter to a USB-C port on your host laptop. Your
computer will automatically detect the device and install all the required drivers.
If you’re running a non-Windows operating system or the drivers do not
automatically install, disconnect the device from your computer, then:
a. Navigate to www.StarTech.com/102B-USBC-MULTIPORT and click the Drivers/
Downloads tab.
b. Under Driver(s), download the Driver Package for your operating system, and
follow the steps outlined in the Installation guide, that’s included in the Driver
Package.
2. When connecting USB peripheral devices, connect a USB-C cable from your USB
peripheral device to the USB-C Data Port on the Multiport Adapter.
Note: The USB port will output whatever bus power is available, up to 4.5W.
3. Connect a USB-A cable from your USB peripheral device to the USB-A Data/
Charge Port on the Multiport Adapter, to connect the device to your computer,
and/or charge your device with up to 5V/1.5A (7.5W).
Notes:
• A USB-C power adapter must be connected to the USB-C DATA/ 100W Power
Delivery Port on the Multiport adapter, in order to charge connected peripheral
devices.
• Without a power adapter connected, the USB port will output whatever bus
power is available, up to 4.5W.
4. Insert your memory card into the SD Card Reader, and press the card to lock it
into place. Your computer will recognize the card and mount it as a drive on your
connected host computer. To remove the memory card, push the card in and
then pull the memory card out.
Note: To protect your memory card and the data stored on it, it’s important to
safely unmount (eject) the card within your computer’s operating system, before
physically removing the card from the Multiport Adapter.
Side B Ports
5. Connect an HDMI cable from up to two HDMI enabled display devices, to the
HDMI Output Ports on the Multiport Adapter, to add additional HDMI displays to
your workstation.
6. Connect a CAT 5e/CAT 6 cable from your local area network (e.g. Router, Switch,
Modem, etc.) to the Gb Ethernet Port on the Multiport Adapter, to access your
network via a wired LAN connection.
Side C Ports
7. Connect a USB-C power adapter (up to 100W) from an AC outlet to the USB-C
100W Power Delivery Port on the Multiport Adapter, to charge the laptop that’s
connected to Built-in USB-C Host Cable.
Note: The Multiport Adapter reserves 15W of power, with up to 85W available
for charging your laptop.
Installation Cont’d
