StarTech.com 25SATSAS35HD User manual

Quick Start Guide
FR: Guide de l’utilisateur - fr.startech.com
DE: Bedienungsanleitung - de.startech.com
ES: Guía del usuario - es.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
IT: Guida per l’uso - it.startech.com
JP: 取扱説明書 - jp.startech.com
Manual Revision: 04/04/2018
For the most up-to-date information, please visit: www.startech.
com/25SATSAS35HD
Package Contents
• 1 x Hard Drive Adapter Enclosure
• 1 x Set of Mounting Hardware
• 1 x Quick Start Guide
Requirements
Hardware:
Note: The following hardware is not included.
• 2.5” Hard Disk Drive (HDD) or Solid State Drive (SSD).
• 3.5” SATA/SAS host device (e.g. computer, docking system, or
backplane).
Note: When installing a SAS Drive into the Hard Drive Adapter
Enclosure, a SAS host device must also be used.
• Philps Head Screw Driver
• Computer with Available Drive Cage/Bay
• (OPTIONAL):
• SATA/SAS Data Cables
• 15-pin SATA Power Connector
• Motherboard with an Available SATA Data Header
Product Diagram
Actual product may vary from photos.
Front View:
1. Release Switch
2. Enclosure Door
3. Mounting Holes (3 per side)
25SATSAS35HD
2.5” SATA/SAS Drive to 3.5” SATA Hard Drive Adapter Enclosure
Rear View:
1. SATA/SAS Power Port
2. SATA/SAS Data Port
Installation (Tool-less)
Installing a Hard Drive into the Hard Drive Adapter
Enclosure:
Warning: Hard drives require careful handling.
1. On the Hard Drive Adapter Enclosure, slide the Release Switch to
the right.
2. The Enclosure Door will open giving you access to the 2.5” drive
slot.
3. (CAREFULLY) insert a 2.5” HDD or SSD (label side up) into the drive
slot. Make sure that the 2.5”HDD or SSD is properly aligned in the
Hard Drive Adapter Enclosure to ensure connectivity (with SATA/
SAS port).
4. (CAREFULLY) close the Enclosure Door, the 2.5”HDD or SSD will
slide into the Hard Drive Adapter Enclosure and connect to the
drive connector, securing the 2.5” HDD or SSD in place.
Mounting
Screw Mount:
Recommended: Leave space around the Hard Drive Adapter
Enclosure, when installing it into a PC or server chassis to ensure
proper airow and heat dissipation.
1. Insert the Hard Drive Adapter Enclosure into the Drive Cage/Bay
label side up.
2. On the Drive Cage/Bay, align the mounting screw holes (on each
side) with the corresponding Mounting Hole on the Hard Drive
Adapter Enclosure.
3. Insert a screw (included) into each of the Mounting Holes.
4. Tighten the screws, making sure not to over-tighten.
1
2
3
12

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.
Industry Canada Statement
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (A)/NMB-3(A)
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s)
to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all
trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and
access our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be
returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages
arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental,
consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not
allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
Tool-less Mount:
For instructions on how to mount the Hard Drive Adapter Enclosure
using a tool-less mount, refer to the manufacturer’s manual for your
PC.
Connecting
Connecting the Hard Drive Adapter Enclosure to a
Motherboard:
1. On the Hard Drive Adapter Enclosure, connect one end of the
SATA/SAS Data Cable into the SATA/SAS data port.
2. On the Motherboard, connect the other end of the SATA Data
Cable into an available SATA/SAS port.
3. Connect 15-pin SATA Power Connector from the PC or server
power supply to the SATA/SAS Power Port on the Hard Drive
Adapter Enclosure.
Product Dimensions
Front View
Side View
Bottom View