StarTech.com SM2NGFFMBU33 User manual

Manual Revision: 12/16/2014
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
SM2NGFFMBU33
USB 3.0 to M.2 NGFF SSD Enclosure
with UASP
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by StarTech.com could void the user’s
authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Product Diagram ....................................................................................1
Enclosure...................................................................................................................................................... 1
Internal Drive Tray..................................................................................................................................... 1
Introduction............................................................................................2
Packaging Contents ................................................................................................................................. 2
System Requirements.............................................................................................................................. 2
Hardware Installation............................................................................3
How to Use ..............................................................................................8
Connecting the Hard Drive.................................................................................................................... 8
Powering the Drive Enclosure .............................................................................................................. 8
Disconnecting the Hard Drive.............................................................................................................. 8
Initializing the Hard Drive ...................................................................................................................... 9
Technical Support ..................................................................................10
Warranty Information............................................................................10

Instruction Manual
1
Product Diagram
Enclosure
Internal Drive Tray
1. Drive tray screws
2. USB 3.0 Micro-B port
1. M.2 (NGFF) SSD Connector
2. Drive installation bracket
3. Drive length adjustment holes

Instruction Manual
2
Introduction
Packaging Contents
• 1 x USB 3.0 SATA HDD/SSD Enclosure
• 1 x USB 3.0 Cable
• 1 x SSD Mounting Screw and Stando
• 1 x Mini Screw Driver
• 1 x Instruction Manual
System Requirements
System Requirements
• Computer system with available USB 3.0 (5 Gbit/s) port or USB 2.0 port (480Mbps)
• M.2 NGFF SATA SSD Drive
Tool Requirements
• 5mm nut driver or small plyers
• Size 1 (PH1) Philips head screw driver

Instruction Manual
3
Hardware Installation
WARNING! SSD Drives and storage adapters require careful handling. If you are
not careful with your SSD Drive, lost data may result. Always handle your drive with
caution. Be sure that you are properly grounded by wearing an anti-static strap when
handling computer components or discharge yourself of any static electricity build-up
by touching a large grounded metal surface (such as the computer case) for several
seconds.
1. Using a Philips head screw driver (not included) Remote the 2 drive tray screws on
either side of the USB 3.0 Micro B port, on the front of the enclosure.
Note: The included screw driver is specically for the SSD installation screw and will
be too small to open the enclosure.
2. Remove the front plate, and slide the internal drive tray out.

Instruction Manual
4
3. Install your M.2 SSD into the drive tray, by following the below steps.
a. Determine if the drive installation bracket requires relocating by assessing your
drive length. The board is labeled with the respective drive types for length but if
your drive type is unknown, place your SSD next to the M.2 (NGFF) SSD connector,
note which drive installation hole matches the height of your SSD. If the bracket is
already installed in the correct position please proceed to step (d.).
b. (Only required if the drive installation bracket requires relocating) Remove
the nut holding the stando in place on the reverse side of the drive tray using a
small set of plyers or 5mm nut driver (Not included).

Instruction Manual
5
c. (Only required if the drive installation bracket requires relocating) Reseat
the drive installation stando in the drive installation hole that matches your SSD.
Replace the removed nut on the reverse side by using a small set of plyers or 5mm
nut driver (not included).
d. Using the included screw driver, remove the screw threaded into the drive
mounting stando.
Note: The connector on your M.2 SSD is keyed so the drive will only t one way.

Instruction Manual
6
e. Slide the M.2 connector on the SSD into the M.2 reciprocal connector on the drive
tray.
f. Press the drive down toward the drive mounting stando, and drive the removed
screw through the mounting hole on your SSD drive and into the drive mounting
stando using the included Philips head screw driver.
Your M.2 SSD is now installed in the internal drive tray.
4. Slide the internal drive tray back into the enclosure so that the USB 3.0 Micro B
connector is facing outward, and place back into position so that the mounting
holes line up.

Instruction Manual
7
5. Using a Philips head screw driver (not included), replace the 2 drive tray screws on
either side of the USB 3.0 Micro B port, on the front of the enclosure.
6. Using the included USB 3.0 cable, connect the SSD enclosure to your computer
system.
Your SSD enclosure is now ready to use.

Instruction Manual
8
How to Use
Connecting the Hard Drive
Once the enclosure has been attached to a computer, and the OS has installed the
necessary software, the drive will be accessible as though it were installed within the
system.
Prior to using the drive, it will need to be formatted according to your operating
system requirements. To format your newly attached hard drive, or create partitions,
please see the Initializing the Hard Drive section.
Powering the Drive Enclosure
The hard drive enclosure requires no external power supply, as it is capable of receiving
enough power from the USB Bus to which it is connected.
Disconnecting the Hard Drive
Windows
1. Select the “Safely remove Hardware and Eject Media” icon, located in the task bar.
2. Select the storage device from the list that appears.
3. Wait for the message indicating that it is now safe to remove the device.
Note: Removing the connected drive prior to receiving notication that it is safe to
do so, could result in losing or corrupting data stored on the drive. Once the Safe
to Remove Hardware message appears, please disconnect the enclosure from the
computer by removing the USB connection.
Mac OS X
To safely disconnect the attached drive from the host computer, close any windows
listing the contents of the removable drive. Once all windows are closed, click on the
USB storage icon on the desktop, and drag it to the Trash Can icon on the desktop.
Allow 5 seconds before physically removing the enclosure/drive from the computer.

Instruction Manual
9
Initializing the Hard Drive
1. If the SATA Hard Drive is blank it may need to be initialized and formatted before
use. From the main Windows desktop, right-click on “My Computer” (“Computer” in
Vista/ 7 / 8/ 8.1), then select Manage. In the new Computer Management window,
select Disk Management from the left window panel.
2. A dialog window should automatically appear, asking you to initialize the drive.
Depending on the version of Windows, it will give you the option of either creating
an “MBR” or “GPT” disk. GPT (GUID partition) is not compatible with some older
operating systems, while MBR is supported by newer and older operating systems.
3. Once initialized, locate the Disk that says it is “Unallocated” (check the listed hard
drive capacity to conrm it’s the correct hard drive) and then right-click in the
section that says “Unallocated” and select “New Partition”.
4. Follow the on screen prompts to initialize the drive in the format of your choice.

Instruction Manual
10
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.

Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.