StarTech.com SV565UTPUSA User manual

Console Extender over
Cat5 UTP
USB, VGA, Serial and Audio
Console Extender over Cat5
UTP
SV565UTPUSA
Instruction Manual

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver•
is connected.
Consult the dealer or an experienced radio/TV technician for help.•
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and
do not represent an endorsement of a product or service by StarTech.com, or an en-
dorsement of the product(s) to which this manual applies by the third-party company in
question. Regardless of any direct acknowledgement elsewhere in the body of this doc-
ument, StarTech.com hereby acknowledges that all trademarks, registered trademarks,
service marks, and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.

i
Table of Contents
Introduction..................................................................... 1
Packaging Contents.....................................................................1
System Requirements .................................................................1
Installation....................................................................... 2
Hardware Installation...................................................................4
Driver Installation.........................................................................5
Configuration .................................................................. 5
Serial Data Link ...........................................................................5
Automatic Calibration Button and Light .......................................5
Manual Calibration and Settings Menu........................................6
Commands ..................................................................................7
Transmitter Unit specific commands............................................7
Image Quality ..............................................................................8
Firmware Upgrade.......................................................................9
Troubleshooting .............................................................. 10
Specifications.................................................................. 12
Technical Support........................................................... 13
Warranty Information...................................................... 13

1
Introduction
Packaging Contents
1 x Transmitter unit•
1 x Receiver unit•
2 x Power Adapter•
1 x USB A-B cable•
1 x VGA extension cable (male/female)•
1 x Instruction Manual•
System Requirements
VGA and USB enabled computer system•
Standard 104-key USB keyboard•
Standard 3-button USB mouse•
VGA enabled monitor•
Additional Receiver units for cascaded operation•

2
Installation
Front View
Transmitter Unit
DE-15 VGA In (male)1.
3.5mm mini-jack audio In2.
3.5mm mini-jack microphone Out3.
USB type B host connector4.
DB9 RS-232 serial (female)5.
Receiver Unit
DE-15 VGA Out (male)1.
3.5mm mini-jack audio Out2.
3.5mm mini-jack microphone In3.
USB type A peripheral connectors4.
DB9 RS-232 serial (male)5.
Receiver Unit
Transmitter Unit
1 2 3 4 5
1 2 3 4 5

3
Rear View
Transmitter Unit
DC Power connector1.
RJ45 Link connector2.
3.5mm mini-jack Audio Out3.
DE-15 VGA Out (female)4.
Receiver Unit
DC Power connector1.
Setup button2.
RJ45 Link Out connector3.
RJ45 Link In connector4.
Receiver Unit
Transmitter Unit 12 3 4
1 2 3 4

4
Hardware Installation
Transmitter Unit
Connect USB cable between PC and USB-B. This also provides1.
power to the Transmitter Unit.
Optional: Connect the 5V power supply to Power In for backup or
if not using a USB cable. A 5V power adapter is required for the
Receiver Unit.
Connect VGA cable between PC and “Video In”.2.
Optional: Connect a monitor to the VGA “Video Out” port.
Connect the Cat5e cable from the RJ45 “Link” port to the first3.
Receiver Unit in the series.
Optional:4. If transmitting audio, connect the speaker/line out on the
computer sound card to “Audio-In“ connector.
Optional:5. Connect speakers to the “Audio-Out” passthrough port.
Optional:6. If you wish to receive audio from a microphone, connect
the mic-in on the computer sound card to the “Mic-out” connector.
Optional:7. Connect the serial port on the computer to DB9 “Serial”
port using a straight-through cable.
Receiver Unit
Connect the 5V power supply to the “Power” connector.1.
Connect a monitor to the “VGA-Out” connector.2.
Connect a USB keyboard/mouse to the USB type A connectors.3.
Connect the Cat5e cable from Transmitter Unit to the “Link In” port.4.
To connect additional Receiver Units, connect a Cat5e cable from5.
the “Link Out” port, to the “Link In”, of any additional units.
Optional:6. Connect a microphone to the “Mic-In” port.
Optional:7. Connect speakers to the “Audio-Out” port.
Optional:8. Connect an RS-232 serial device to the “Serial” port.

5
Driver Installation
No drivers or additional software need to be installed on the host
computer.
Conguration
Serial Data Link
The SV565UTPUSA is able to link two RS232 ports together to allow
touchscreens, monitor control ports and other devices to be used
remotely. The port’s baud rate is detected automatically and supports
300 to 19200 bps, with 9600 being the preferred rate. If using a baud
rate other then 9600 it may take several bytes of data being sent to
properly calibrate it. By default the first Receiver Unit has control of
the serial port, but any Receiver Unit can be accessed by using the
configuration menu on the Transmitter Unit.
Automatic Calibration Button and Light
SV565UTPUSA is able to automatically calibrate to different cable
lengths in order to preserve image quality. This allows it to work out
of the box without any adjustments. Once a good calibration setting is
attained, it can be set into fixed calibration mode. This ensures it uses
the same settings if it is reset or powered off.
The calibration button on the back of the Receiver Unit can be pressed
with the tip of a pen. The image will display a brief test pattern and the
indicator light will flash. If it is held for more then half a second, it will
switch to fixed calibration mode. In fixed mode the indicator LED below
the button will light up and auto calibration will not occur in this state.
Press and hold the button again to return to auto calibration mode.

6
Manual Calibration and Settings Menu
A text-based menu is available on the serial port of both the Transmitter
and Receiver units. This can be used to make fine adjustments to the
image quality. The menu can be accessed by connecting the serial port
to a PC or laptop using a straight-through cable for Transmitter Unit or
a null modem cable for Receiver Unit. For computers that don’t have
a serial port built in, the StarTech.com ICUSB232 can be used. You
can use any terminal communication software to connect to the serial
port, such as minicom for UNIX, and HyperTerminal or TeraTerm for
Windows.
If the serial data link is being used, the Transmitter Unit will already
be set up for serial communication. To connect to a Receiver Unit the
serial device must be unplugged first and replaced with the RS232 null
modem cable. Use the same baud rate that the serial device and PC
had used to communicate.
If you are not using the serial link just attach the RS232 cable and use
9600 bps. Also configure the terminal software to use 8N1, or 8 bits
with no parity and 1 stop bit.
An escape code is used to enter the serial menu from data transfer
mode. The code is a one second delay, followed by 3x @ symbols,
then another one second delay. A confirmation message will appear if
it works. If it does not appear, try again a few times because it depends
on timing. To exit the menu press X to return to data transfer mode.
Commands are case sensitive.
The Transmitter Unit is able to access all of the Receiver units attached
to it, allowing changes to be made from a central location. Also the
Transmitter Unit can change which Receiver Unit has the serial link
enabled. Receiver units can change their own settings, allowing for
fine-tuning to be made in the field using a laptop.

7
Commands
h - Help, show all commands
p - Print settings
f - Auto calibration enable
F - Fixed config enable. Use this to lock in the settings after adjusting
Auto calibrate next Receiver Unit in the chain. Use this after youn -
make any adjustments to vCtrl or gain
z/x - Decrease/increase gain for brightness
c/v - Decrease/increase vCtrl for distance compensation
a/s - Decrease/increase Red skew compensation
q/w - Decrease/increase Green skew compensation
1/2 - Decrease/increase Blue skew compensation
0 - Restore factory default settings and recalibrate
R - Reset device
X - Exit menu and restore serial link mode
Transmitter Unit specic commands
Get calibration from a certain Receiver unit. You must do this firstg -
in order to change any settings. Type the desired Receiver Unit
address and then Enter
Select which Receiver Unit gets the serial port link to ther -
Transmitter Unit
The first Receiver Unit has address 1, the second has address 2, etc.
Gain adjusts the brightness of the signal caused by losses in the cable.
This does not normally need to be fine tuned, it is better to adjust
the monitor’s settings if it is too dark, too bright or has color balance
problems.