StarTech.com 410VDSLEXT User manual

Manual Revision: 06/04/2012
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
410VDSLEXT
410VDSLEXTGB
410VDSLEXTEU
4 Port 10/100 VDSL Ethernet Extender
Kit over Single Pair - 1km
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use ofTrademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Introduction............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements.............................................................................................................................. 1
Front View................................................................................................2
Rear View .................................................................................................2
Installation ..............................................................................................3
Hardware Installation .............................................................................................................................. 3
Driver Installation...................................................................................................................................... 3
Conguration..........................................................................................3
Web Interface ............................................................................................................................................. 3
Specications..........................................................................................10
Technical Support ..................................................................................11
Warranty Information............................................................................11

Instruction Manual
1
Introduction
The 410VDSLEXT 10/100 4-Port VDSL Ethernet Extender Kit lets you span a 10/100
network over single pair wire at distances up to 1km, to multiple users or network
segments while maintaining high-speed network connectivity.
With the ability to run over new or existing RJ45 cabling, RJ11 phone lines, or any other
single pair wire, the 4-port VDSL2 kit provides a simple, out-of-the-box solution that
includes both the Ethernet-VDSL extender and receiver units.
Perfect for connecting isolated user stations within, or between buildings, or to overcome
infrastructure obstacles (e.g. stone/concrete architecture) where new wiring or wireless
may be impossible. This LAN extender kit also helps to eliminate expense by allowing video
streaming and data to share the same telephone pair without interference.
Backed by a StarTech.com 2-year warranty and free lifetime technical support.
Packaging Contents
• 1x Extender Unit
• 1x Receiver Unit
• 1x RJ-45 Cable
• 1x RJ-11 Cable
• 2x Power Adapter
• 1x Instruction Manual
System Requirements
• 10/100 Mbps Ethernet Network
• Available AC electric outlets

Instruction Manual
2
Front View
Rear View
LAN
1234
PWR WAN
410VDSLEXT
VDSL Extender
CO Modem CPE Modem
RJ-45 Ethernet
Connectors
RJ11 Line
RJ11 Phone
Connector
DB9 Serial
DC Power
Connector
CO Modem
CPE Modem

Instruction Manual
3
Installation
Hardware Installation
1. Place each VDSL Extender unit at their respective end-point locations. Make sure an
AC electrical outlet is located nearby.
2. Connect the included power adapters to the pair of VDSL Extender units. The Power
LED should light up solid.
3. Connect the “Line”RJ11 connector on the VDSL Extender units either directly
together with patch cabling, or to a buildings existing analog telephone wiring. If
the two units are able to successfully communicate with each other, the “WAN” LED
should light up solid.
OPTIONAL: If the telephone wiring is also used for POTS telephone service, then a
telephone may be connected to the“Phone”RJ11 connector on the VDSL Extender units.
4. Connect each computer, or Ethernet networking device to an available RJ45
connector on the VDSL Extender units. The respective LAN LED should light up to
indicate a successful physical connection.
Driver Installation
No driver or software installation is required.
Conguration
Web Interface
Each of the VDSL Extender units have a built-in web interface, for conguring the
router settings (WAN and LAN ports), if necessary. The interface can be access via
their IP addresses (CO Modem: 192.168.16.249, CPE Modem: 192.168.16.250). The
default password is: admin
The main menu screen on the CPE Modem has two options:“Setup Wizard” for quick
setup, and “Advanced Setup” for a more customized conguration. The CO Modem
only has “Advanced Setup”options.

Instruction Manual
4
Setup Wizard (CPE Modem only)
The Setup Wizard allows for quick and easy conguration of the most common settings
(WAN) for the VDSL Extender.
Advanced Menu System
This section allows for general conguration/administration of the VDSL Extender unit.

Instruction Manual
5

Instruction Manual
6
WAN
This section can congure how the built-in VDSL Modem connects to a DSL Internet
Service Provider (ISP) through the “Line” RJ11 connector. The modem supports
Dynamic IP, Static IP and PPPoE modes.
LAN
The LAN section is used to congure the IP address and DHCP server on the RJ45
Ethernet side of the VDSL Extender unit. By default the DHCP server is not enabled.

Instruction Manual
7
NAT
This section is used to congure the advanced features on the Ethernet side of the
VDSL Extender unit. This include “Virtual Server”, “Port Mapping”and DMZ settings.