StarTech.com HDMIPATTERN2 User manual

Video Pattern Generator
HDMI/DVI Portable Video Test
Pattern Signal Generator
HDMIPATTERN2
HDMIPATRN2GB
HDMIPATRN2EU
Instruction Manual
Manual Revision:11/18/2010
For the most up-to-date information, please visit www.startech.com

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and
Symbols
Thismanualmaymakereferencetotrademarks,registeredtrademarks,andother
protectednamesand/orsymbolsofthird-partycompaniesnotrelatedinanywayto
StarTech.com. Where they occur these references are for illustrative
purposes only and do not represent an endorsement of a product or service
by StarTech.com, or an endorsement of the product(s) to which this manual
applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com
hereby acknowledges that all trademarks, registered trademarks, service
marks, and other protected names and/or symbols contained in this manual
and related documents are the property of their respective holders.

i
Table of Contents
Introduction......................................................... 1
Packaging Contents....................................................... 1
System Requirements ................................................... 1
Front View...................................................................... 2
Top View ........................................................................ 2
Installation........................................................... 3
Specifications...................................................... 5
Technical Support............................................... 6
Warranty Information .......................................... 6

1
Introduction
The HDMIPATTERN2 HDMI/DVI Portable Video Signal Generator lets
you quickly test DVI-D (digital) and HDMI-capable displays, making it
easier to diagnose and troubleshoot digital video calibration issues.
The device can be powered by either the included AC adapter or a 9V
battery, offering a conveniently portable solution for mobile installers
and technicians.
The video signal generator features 8 built-in video test patterns,
including both HD video test patterns and standard definition patterns,
allowing you to quickly analyze color performance, linearity, and HDCP
issues.
Delivering a cost-effective way to test HDMI or DVI-D displays (using
an HDMI to DVI cable - not included), the pattern generator is an ideal
solution for AV install experts/integrators or digital signage installers
looking to save time and solve problems with an HDTV display.
Backed by a StarTech.com 1-year warranty and free lifetime technical
support.
Packaging Contents
• 1 x HDMI pattern generator
• 1 x HDMI cable
• 1 x Power Adapter
• 1 x Instruction Manual
System Requirements
• HDMI or DVI-D enabled display device (i.e. monitor, projector,
HDTV, etc)
• Available AC power outlet or 9V battery

2
Front View
Top View

3
Installation
1. The video generator can be powered either by external power
adapter or a 9V battery. To access the battery compartment, flip the
unit over and on the bottom side, will be the battery door. Push in
the small tab that secures the door and lift the door away from the
unit.
2. Set the Video Resolution Switch to the desired output resolution for
the display device (i.e. monitor, HDTV, etc) you wish to calibrate/test.
Swtich Setting Description
1080p/12 1080p @ 60Hz (12-bit)
1080p/10 1080p @ 60Hz (10-bit)
1080p/8 1080p @ 60Hz (8-bit)
1080i/8 1080i @ 60Hz (8-bit)
720p/10 720p @ 60Hz (10-bit)
720p/8 720p @ 60Hz (8-bit)
480p/8 480p @ 60Hz (8-bit)
3. Connect the video generator to the display device using an HDMI
cable or HDMI-to-DVI adapter/cable.
4. Set the Power Switch to the ON position, and the Power LED should
light up solid. If using battery power, then the battery becomes low,
the LED will start to flash.
5. If the display device is HDCP compliant, than the HDCP Error LED
should NOT light up. If the LED lights up, then there is a problem
with HDCP verification.

4
6. The current test pattern should be display on the display device.
Pressing the Test Pattern Selection Switch will toggle through each
of the available test patterns.
Test Patterns

5
Specications
Video Signal High Speed HDMI (1.3)
Connectors 1 x HDMI type A female
1 x DC Power
LEDs 1 x Power/Battery Status
1 x HDCP Error
Video Resolution Support
480p (60Hz, 8-bit),
720p (60Hz, 8/10-bit),
1080i (60Hz, 8-bit),
1080p (60Hz, 8/10/12-bit)
HDCP Support HDCP 1.2
Number of Test Patterns 8
Maximum Cable Distance 5 m / 16.4 ft
Enclosure Material Plastic
Power Source 9V battery
9VDC, 600mA power adapter
Operating Temperature 0°C ~ 70°C (32°F ~ 158°F)
Storage Temperature -20°C ~ 85°C (-4°F ~ 185°F)
Humidity 0% ~ 95%
Dimensions 132.0mm x 87.0mm x 28.0mm
Weight 150 g

6
Technical Support
StarTech.com’s lifetime technical support is an integral part of our
commitment to provide industry-leading solutions. If you ever need
help with your product, visit www.startech.com/support and access
our comprehensive selection of online tools, documentation, and
downloads.
Warranty Information
This product is backed by a one year warranty.
In addition, StarTech.com warrants its products against defects
in materials and workmanship for the periods noted, following
the initial date of purchase. During this period, the products may
be returned for repair, or replacement with equivalent products
at our discretion. The warranty covers parts and labor costs
only. StarTech.com does not warrant its products from defects or
damages arising from misuse, abuse, alteration, or normal wear
and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.
com USA LLP (or their officers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive,
incidental, consequential, or otherwise), loss of profits, loss of
business, or any pecuniary loss, arising out of or related to the
use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental
or consequential damages. If such laws apply, the limitations or
exclusions contained in this statement may not apply to you.

StarTech.com has been making “hard-to-find easy” since
1985, providing high quality solutions to a diverse IT and
A/V customer base that spans many channels, including
government, education and industrial facilities to name
just a few. We offer an unmatched selection of computer
parts, cables, A/V products, KVM and Server Management
solutions, serving a worldwide market through our locations
in the United States, Canada, the United Kingdom and
Taiwan.
Visit www.startech.com today for complete information
about all our products and to access exclusive interactive
tools such as the Cable Finder, Parts Finder and the KVM
Reference Guide.