StarTech.com IES5100 User manual

Manual Revision: 11/24/2011
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
IES5100
5 Port Unmanaged Industrial Ethernet Switch
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and
Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Introduction............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements.............................................................................................................................. 1
Installation ..............................................................................................2
DIN Rail Mounting..................................................................................................................................... 2
Connecting to Power............................................................................................................................... 2
Network Connection................................................................................................................................ 3
LED Displays................................................................................................................................................ 3
Specications..........................................................................................4
Technical Support ..................................................................................5
Warranty Information............................................................................5

Instruction Manual
1
Introduction
The IES5100 5 Port Unmanaged Industrial Ethernet Switch (DIN-Rail Mountable) oers
ve 10/100 Ethernet switching ports and is designed to operate in harsh environments,
making it an ideal solution for factory oors, warehouses, and outdoor locations
without temperature control.
This versatile switch features 10/100Mbps transfer speeds, full/half-duplex auto-
negotiation and auto MDI/MDIX operation allowing you to connect your network
devices quickly and easily with little to no conguration required.
The Ethernet switch can be DIN rail mounted and features compact, hardened
construction that can be installed in any environment, able to operate within extended
temperature ranges from -10°C to 60°C.
Packaging Contents
• 1 x 5 Port Ethernet Switch
• 1 x Instruction Manual
System Requirements
• 2 or 3-wire 12~48V DC power source
• 10/100Mbps compatible Ethernet network

Instruction Manual
2
Installation
DIN Rail Mounting
1. Hook the top, xed DIN rail bracket on the rear
of the Ethernet Switch to the top edge of the
DIN rail.
2. Push the lower portion of the Ethernet Switch
back against the DIN rail, which will cause
the bottom, spring-loaded DIN clip to snap in
place.
3. To remove the Ethernet Switch from the DIN
rail, pull the small tab on the bottom of the
spring-loaded clip to release it.
Connecting to Power
1. Gently, yet rmly pull the terminal block connector housing from the Ethernet
Switch.
2. Using a small at head screw driver, loosen the screws for the terminal block
connectors.
3. Connect the power and ground wires from your DC power source to the proper
terminal block connectors and fasten the screws. The terminals are marked on the
Ethernet Switch housing.
4. Reinsert the terminal block housing into the Ethernet Switch.

Instruction Manual
3
Network Connection
1. Ensure that both the IES5100 and any devices that are to be connected to it are
powered o.
2. Prepare the necessary cabling for each device that is to be attached to the IES5100.
Use the following chart as reference for cabling types:
Speed Connector Port Speed
(Half/ Full Duplex) Cable Type Max.
Distance
10Base-T RJ45 10/20 Mbps 2-pair UTP/STP
Cat. 3, 4, 5 100 m
100Base-TX RJ45 100/200 Mbps 2-pair UTP/STP
Cat. 5 100 m
3. Connect the cable to both the IES5100 and attached devices and turn them on.
4. Check to ensure that both devices are transmitting and receiving data by checking
their LED displays. (See next section for details)
LED Displays
The IES5100 has LED indicators for each of the RJ45 ports on the switch to show the
status of each connections.
LED State Indication
LNK/ACT Steady Valid network connection established
Flashing Transmitting or receiving data
100
Steady Port is transferring at 100Mbps
O Port is transferring at 10Mbps or is not
transferring

Instruction Manual
4
Specications
Number of Ports 5
Connectors 5 x RJ45 Ethernet female
1 x 3-wire Terminal Block
LEDs
1 x Power
1 x Link/Activity (per port)
1 x Link Speed (per port)
Switching Method Store-and-Forward
Supported Standards IEEE 802.3, IEEE 802.3u
Network Link Speeds 10/100 Mbps
Auto MDIX Yes
Full Duplex Yes
Enclosure Material Plastic
Power Supply 12 ~ 24V DC
Operating Voltage/Current 0.2A @ 12VDC, 0.1A @ 24VDC, 0.05A @
48VDC
Maximum Power Consumption 2.4W
Operating Temperature -10°C ~ 60°C (14°F ~ 140°F)
Storage Temperature -25°C ~ 85°C (-14°F ~ 185°F)
Humidity 5% ~ 95% RH
MTBF 1,677,807 Hours
Dimensions (LxWxH) 70.0mm x 26.0mm x 110.0mm
Weight 200g

Instruction Manual
5
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.

Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.