StarTech.com SV231DPDDUA User manual

Manual Revision: 01/11/2012
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
SV231DPDDUA
2 Port Dual DisplayPort USB KVM Switch
with Audio & USB Hub
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use ofTrademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Introduction............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements.............................................................................................................................. 1
Front View.................................................................................................................................................... 2
Rear View...................................................................................................................................................... 2
Installation ..............................................................................................3
Hardware Installation .............................................................................................................................. 3
Driver Installation...................................................................................................................................... 4
Operation ................................................................................................5
Front Panel................................................................................................................................................... 5
HotKey Control........................................................................................................................................... 5
Alternative Hotkey Commands............................................................................................................ 8
Change Leading Hotkey......................................................................................................................... 9
Specications..........................................................................................10
Technical Support ..................................................................................11
Warranty Information............................................................................11

Instruction Manual
1
Introduction
The SV231DPDDUA 2-Port USB Dual DisplayPort KVM Switch with Audio and USB 2.0
Hub combines next generation digital display standards with seamless KVM control,
allowing you to switch between 2 dual head or twin DisplayPort systems. Also ideal
for systems with a single DisplayPort output, and a second video source such as DVI or
HDMI, using a low cost accessory adapter.
Delivering multi-computer control for high-res multimedia applications, the dual view
KVM supports resolutions of 2560x1600 (@60 Hz) with DisplayPort HD audio, as well as
2-channel analog stereo audio and microphone input.
Suitable for high quality static imaging, such as medical applications (MRI, X-ray, etc.), a
maximum resolution of 3840x2400 is supported at reduced refresh rates
Backed by a StarTech.com 3-year warranty and free lifetime technical support.
Packaging Contents
• 1 x SV231DPDDUA KVM switch
• 1 x Power Adapter
• 1 x Rubber Feet
• 1 x Instruction Manual
System Requirements
• DisplayPort enabled display device (e.g. monitor, projector, TV, etc.)
• DisplayPort enabled computer system/video card
• USB enabled computer system
• Standard 104-key wired USB keyboard
• Standard 3-button wired USB mouse
• 3.5mm mini-jack Microphone and/or Speakers (OPTIONAL)

Instruction Manual
2
Front View
Rear View
Port Selection/Link
LED Port Selection
Button

Instruction Manual
3
Installation
NOTE: Prior to the installation, please power o all devices that will be connected to
this system.
Ensure that all devices you will connect are properly grounded.
Place cables away from uorescent lights, air conditioners, and machines that are likely
to generate electrical noise.
If you experience any problems using a USB KVM switch, the following BIOS setup
changes may be necessary for PC users and not necessary for Mac users:
• Set HALT ON ERROR to ALL BUT KEYBOARD.
• In PNP AND PCI SETUP, set PNP OS INSTALLED to YES and set USB IRQ to ENABLED.
Dierent systems may use dierent naming, so contact your system manufacturer for
further assistance with these settings.
Hardware Installation
*installation pictures are representations only
1. Plug one or two monitor(s) into the Console’s DisplayPort connector; plug a USB
keyboard and a USB mouse into the dedicated USB keyboard and mouse ports on
the KVM switch. If using audio, also connect speakers with 3.5mm mini-jack plugs.
2. Use male-to-male DisplayPort video cable(s) to connect the DisplayPort
connector(s) on the computer’s video card, to one of the KVM’s PC ports (i.e. PC1).
3. Use a USB type A-B Cable to connect the KVM’s USB port (type B, square connector)

Instruction Manual
4
for the PC port used in Step 2, and the USB port on the computer (type A, at
connector). If using audio, connect 3.5mm mini-jack cables from the PC port to the
sound card.
NOTE: A DisplayPort + USB KVM combo cable is also available which can be used in
place of separate individual cables, StarTech.com ID: DP4N1USB6.
4. Repeat Steps 2 and 3 for each PC port on the KVM switch, or each computer you
wish to use on the KVM.
5. OPTIONAL: Connect any other USB peripherals you wish to share between the
connected computers/devices to the extra USB Hub ports on the Console side.
6. Connect the external power adapter from a wall outlet to the power connector on
the rear panel of the KVM switch.
7. Power up the rst computer/device and wait for it to fully boot and test keyboard/
mouse functionality.
8. Once operation has been successfully conrmed, switch to the next port and power
up that computer/device and conrm.
9. Once completed for all computers/devices connected to the KVM switch, you
should be able to switch between ports freely.
Driver Installation
No driver installation is required for the KVM switch, as the keyboard and mouse
use generic USB keyboard/mouse drivers that are already installed on any operating
system that fully supports USB.

Instruction Manual
5
Operation
Front Panel
Port Selection/Link LED
The LED turns green when the connected computer is powered-on. The corresponding
LED will also illuminate red when that PC port is currently selected.
Port Selection Button
Each push of the Selection Button on the front of the KVM switch will immediately
switch between the two ports on the KVM switch.
AutoScan
The system automatically scans through the power-on computers in sequence with a
xed interval (see Scan Time below).
Scan Time
Four options are available for users to set the Scan Time duration, it Includes 3, 8, 15
and 30 seconds.
Note: Scan Time is set to 3 seconds by default.
HotKey Control
A Hotkey command is a short keyboard sequence for selecting a computer, activating
computer scan, etc. A hotkey sequence starts with two left <CTRL> keystrokes
(successively within 0.2 seconds) followed by one or two more keystrokes. A built-in
tone generator creates a high-pitch beep for correct hotkey command; otherwise, one
low-pitch beep is generated for errors and the bad key sequence will not be forwarded
to the selected computer.
NOTE: Press and hold Left <SHIFT> and press <NumLock> twice, then release <SHIFT>
followed by pressing left <CTRL> once, which will enable / disable the hotkey feature.
To select a computer:
Left <CTRL> + Left <CTRL> + <1>
(Example: Selects the computer at port 1.)
Left <CTRL> + Left <CTRL> + <2>
(Example: Selects the computer at port 2.)
NOTE: Do not use the keypad on the right-side of the keyboard.

Instruction Manual
6
Auto Scan
The KVM automatically scans through the powered-on computers in sequence on a
xed time interval (see Scan Time below).
Note: The keyboard and mouse are not operable during Auto Scan.
To start Auto Scan:
Left <CTRL> + Left <CTRL> + <F1>
To abort the Auto Scan mode, press the left <CTRL> key twice. When Auto Scan detects
any keyboard or mouse activity, it suspends the scanning till the activity stops; it then
resumes with the next computer in sequence. The length of the Auto Scan interval
(Scan Time) is adjustable, see below.
Manual Scan allows users to manually switch back and forth between powered-on
computers.
Left <CTRL> + Left <CTRL> + <F2>
To select the previous or the next computer, press <UP> or <DOWN> arrow keys. To
abort the Manual Scan, press any other key.
Scan Time
Four options are available for users to set the Scan Time duration, it Includes 3, 8, 15
and 30 seconds.
Note: Scan Time is set to 3 seconds by default.
To adjust Scan Rate, set the scan time of duration before switching to the next computer:
Left <CTRL> + Left <CTRL> + <F3>
The KVM Switch generates 1 to 4 beeps indicating a scan time duration for 3, 8, 15 or
30 seconds respectively.

Instruction Manual
7
Audio Lock
There are two options for Audio Lock: ON and OFF. When ON, audio selection follows
computer selection. When OFF, audio selection stops following computer selection. It
is useful if you want to listen to a particular computer’s audio signal while operating
other computers.
Left <CTRL> + Left <CTRL> + <F5>
The KVM switch beeps once or twice corresponding to ON and OFF respectively.
To change which computer port the audio stays on to the currently selected port, press
the following hotkey:
Left <CTRL> + Left <CTRL> + <A>
USB-Port Rule
There are two settings for USB-Port Rule: ON or OFF.
When set to ‘ON’, the USB Hub ports follows computer selection.
When set to ‘OFF’, the USB Hub ports stays on the currently selected PC port.
Pressing the hotkey below to turn ON/OFF the USB-Port Rule on both USB Hub ports:
Left <CTRL> + Left <CTRL> + <F7>
To change the PC port that the USB hub stays on to the currently selected PC port,
press the following hotkey:
Left <CTRL> + Left <CTRL> + <U>
NOTE: Please make sure that installation of the USB device has been accomplished
before switching to the next computer.