StarTech.com HB30A10AME User manual

Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: June 5, 2019 4:02 PM
Product Diagram (HB30A10AME)
Component Function
12-Wire Terminal Block • Used to connect an external DC Power Source
(7~24V DC Input) to the Hub.
2Screw Locks (x 10)
• Used to securely lock a USB Device to the
USB-A Port on the Hub.
• Screw Lock Dimensions: Center to center 19
mm, thread size 4 - 40.
3Power LED • Green: Indicates that the Hub is receiving
power.
4USB-B Host Port
• Used to connect a Host Computer to the Hub.
• Screw Lock Dimensions: Center to center 24
mm, thread size 4 - 40.
5USB-A Ports (x 10)
• Used to connect USB Devices ( x 10) to the
Hub.
• Used to charge connected USB-A Devices.
• USB-A Ports support surge and 15KV ESD
(Electrostatic Discharge) Protection.
10-Port Industrial USB 3.0 (5 Gbps) Hub | USB 3.1 Gen 1 to 10x USB-A | ESD & Surge Protection
3
Requirements
For the latest requirements, please visit www.startech.com/HB30A10AME .
• Phillips Head Screwdriver
• Writing Utensil
• Level
• Mounting Screws (x 2)
Installation
Notes: It is recommended to use an external DC Power Source (+7 - 24V DC)
connected to the 2-Wire Terminal Block to ensure sucient power/current is
delivered to each USB-A Port on the Hub.
The Hub can also be powered by a Host Computer connected to the USB-B Host
Port, when using low power consuming USB Devices.
Powering the Hub Using the Universal Power Adapter
1. Connect the Universal Power Adapter to the Terminal Block and to a AC
Electrical Outlet.
2. Connect a USB-B to USB Cable (the end will depend on USB Port you are
connecting to) to the USB-B Host Port and to a USB port on the Host Computer.
3. The Host Computer’s Operating System should detect the Hub and automatically
install it.
4. Connect your USB Devices to the USB-A Ports (x 10) on the Hub.
Powering the Hub Using USB
1. Connect a USB-B to USB Cable (the end will depend on USB Port you are
connecting to) to the USB-B Host Port and to a USB port on the Host Computer.
2. The Host Computer’s Operating System should detect the Hub and automatically
install it.
3. Connect your USB Devices to the USB-A Ports (x 10) on the Hub.
Powering the Hub Using the 2-Wire Terminal Block
1. Remove the Terminal Block Connector Housing from the Hub’s Casing.
2. Using a small screwdriver (Phillips or Flat Head), loosen the screws on the Terminal
Block Connectors.
45
2
1

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
2500 Creekside
Parkwy
Lockbourne, Ohio
43137
U.S.A.
Din Rail Mounting
Wall Mounting
It is recommended that you use Wall Studs when wall mounting the Hub.
1. Align the Hub on the wall in the position you want to mount the Hub.
2. Using a Writing Utensil mark o both of the Mounting Holes.
3. Using a Level draw a line connecting the two Mounting Holes, making sure that
the line is level.
4. Align the Mounting Holes on the Hub with the Mounting Hole Marks.
5. Insert the Mounting Screws (x 2) through the Wall Mounting Holes and into the
Wall.
6. Using a Phillips Head Screwdriver tighten the Mounting Screws until the Hub is
securely fasten to the Wall.
3. Connect the Power and Ground Wires from your DC Power Source (+7 - 24V DC)
to the proper Terminal Block Connectors, the terminals are marked on the Hub’s
Casing.
Note: Ensure the polarity of the input power is correctly matched with the Terminal
Block Pins to ensure proper function.
Terminal Block Pins
4. Insert the Terminal Block Housing onto the Hub’s Casing.
Mounting
DIN Rail Mounting
1. Align the Din Rail Brackets (x 2) with the Mounting Holes (x 4) on the back of the
Hub.
2. Insert the Mounting Screws (x 4) through the Din Rail Brackets and into the Hub.
3. Using a Phillips Head Screwdriver tighten the Mounting Screws. Be careful not to
over-tighten the Mounting Screws.
4. Clip the Din Rail Brackets onto a Din Rail, securing the Hub to the Din Rail.