StarTech.com SV431DPUA User manual

DisplayPort KVM Switch
4-Port Professional USB,
DisplayPort KVM Switch
with Audio
SV431DPUA
Instruction Manual

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver•
is connected.
Consult the dealer or an experienced radio/TV technician for help.•
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an
endorsement of the product(s) to which this manual applies by the third-party company
in question. Regardless of any direct acknowledgement elsewhere in the body of
this document, StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this
manual and related documents are the property of their respective holders.

i
Table of Contents
Introduction..................................................................... 1
Packaging Contents.....................................................................1
System Requirements .................................................................1
Installation....................................................................... 1
Hardware Installation...................................................................2
Front View....................................................................................2
Rear View ....................................................................................2
Driver Installation.........................................................................4
Operation......................................................................... 4
Front Panel ..................................................................................4
HotKey Control ............................................................................5
Alternative Hotkey Commands ....................................................8
Specifications.................................................................. 10
Technical Support........................................................... 11
Warranty Information...................................................... 11

1
Introduction
Packaging Contents
1 x SV431DPUA KVM switch•
1 x Power Adapter•
1 x Rubber Feet•
1 x Instruction Manual•
System Requirements
DisplayPort enabled computer system•
USB enabled computer system•
Standard 104-key USB keyboard•
Standard 3-button USB mouse•
Installation
NOTE: Prior to the installation, please power off all devices that will be
connected to this system.
Ensure that all devices you will connect are properly grounded.
Place cables away from fluorescent lights, air conditioners, and
machines that are likely to generate electrical noise.
If you experience any problems using a USB KVM switch, the
following BIOS setup changes may be necessary for PC users and not
necessary for Mac users:
Set HALT ON ERROR to ALL BUT KEYBOARD.•
In PNP AND PCI SETUP, set PNP OS INSTALLED to YES and set•
USB IRQ to ENABLED.
Different systems may use different naming, so contact your system
manufacturer for further assistance with these settings.

2
Hardware Installation
Front View
Rear View
USB Hub
ports
USB keyboard/
mouse ports
Console
DisplayPort
port
External
power port
PC4 Port PC3 Port PC2 Port PC1 Port
3.5mm speaker/
MIC ports
Port
Selection
Buttons
PC Port Power/
Selection LED
KVM Power
LED

3
*installation pictures are representations only
Plug a monitor into the Console’s DisplayPort connector; plug a USB1.
keyboard and a USB mouse into the dedicated USB keyboard and
mouse ports on the KVM switch.
Use a male-to-male DisplayPort video cable to connect the2.
DisplayPort connector on the computer’s video card, to one of the
KVM’s PC ports (i.e. PC1)
Use a USB type A-B Cable to connect the KVM’s USB port (type B,3.
square connector) for the PC port used in Step 2, and the USB port
on the computer (type A, flat connector).
Repeat for Steps 2 and 3 for each PC port on the KVM switch, or4.
each computer you wish to use on the KVM.

4
OPTIONAL:5. Connect any other USB peripherals you wish to share
between the connected computers/devices to the extra USB Hub
ports on the Console side.
Connect the external power adapter from a wall outlet to the power6.
connector on the rear panel of the KVM switch.
Power up the first computer/device and wait for it to fully boot and7.
test keyboard/mouse functionality.
Once operation has been successfully confirmed, switch to the next8.
port and power up that computer/device and confirm.
Once completed for all computers/devices connected to the KVM9.
switch, you should be able to switch between any ports freely.
Driver Installation
No driver installation is required for the KVM switch, as the keyboard
and mouse use generic USB keyboard/mouse drivers that are already
installed on any operating system that fully supports USB.
Operation
Front Panel
PC Link/Selection LED
The LED turns green when the connected computer is powered-on.
The corresponding LED will also illuminate red when that PC port is
currently selected.
Port Selection Button
Each push button on the front of the KVM switch corresponds with a
PC port. Pressing that button will immediately select that port.

5
AutoScan
The system automatically scans through the power-on computers in
sequence with a fixed interval (see Scan Time below).
To activate AutoScan, press front panel push buttons “3” and “4”
simultaneously. The port selection LED will flash during AutoScan.
AutoScan will select active computers only. To exit AutoScan mode,
just press any one of the front panel push buttons.
Scan Time
Four options are available for users to set the Scan Time duration, it
Includes 3, 8, 15 and 30 seconds.
Note: Scan Time is set to 3 seconds by default.
To change the Scan Time, press front panel buttons “1” and “2”
simultaneously. The unit will respond with beep(s) of 1, 2, 3 or 4 times
for a Scan Time of 3, 8, 15 or 30 seconds respectively.
HotKey Control
A Hotkey command is a short keyboard sequence for selecting a
computer, activating computer scan, etc. A hotkey sequence starts
with two left <CTRL> keystrokes ( successively within 0.2 seconds )
followed by one or two more keystrokes. A built-in buzzer generates a
high-pitch beep for correct hotkey command; otherwise, one low-pitch
beep is generated for errors and the bad key sequence will not be
forwarded to the selected computer.
NOTE: Press and hold Left <SHIFT> and press <NumLock> twice,
then release Shift followed by pressing left <CTRL> once, which will
enable / disable the hotkey feature.

6
To select a computer:
Left <CTRL> + Left <CTRL> + 1
(Example: Selects the computer at port 1.)
Left <CTRL> + Left <CTRL> + 2
(Example: Selects the computer at port 2.)
NOTE: Do not use the keypad on the right-side of the keyboard.
Auto Scan
The KVM automatically scans through the powered-on computers in
sequence on a fixed time interval (see Scan Time below).
Note: The keyboard and mouse are not operable during Auto Scan.
To start Auto Scan:
Left <CTRL> + Left <CTRL> + F1
To abort the Auto Scan mode, press the left <CTRL> key twice. When
Auto Scan detects any keyboard or mouse activity, it suspends the
scanning till the activity stops; it then resumes with the next computer
in sequence. The length of the Auto Scan interval (Scan Time) is
adjustable, see below.
Manual Scan allows users to manually switch back and forth between
power-on computers.
Left <CTRL> + Left <CTRL> + F2
To select the previous or the next computer, press <UP> or <DOWN>
arrow keys. To abort the Manual Scan, press any other key.

7
Scan Time
Four options are available for users to set the Scan Time duration, it
Includes 3, 8, 15 and 30 seconds.
Note: Scan Time is set to 3 seconds by default.
To adjust Scan Rate, set the scan time of duration before switching to
the next computer:
Left <CTRL> + Left <CTRL> + F3
The KVM Switch generates 1 to 4 beeps indicating a scan time
duration for 3, 8, 15 or 30 seconds respectively.
Audio Stick
There are two options for Audio Stick: ON and OFF. When ON, audio
selection follows computer selection. When OFF, the current port’s
audio is used for all other ports. It is useful if you want to listen to a
particular computer’s audio signal while operating other computers.
Press Left <CTRL> + Press Left <CTRL> + Press F5
The KVM switch beeps once or twice corresponding to ON and OFF
respectively.
To change which port the audio is following to the currently selected
port, press the following hotkey:
Press Left <CTRL> + Press Left <CTRL> + Press A
USB-Port Rule
There are two settings for USB-Port Rule: ON or OFF.
When set to ‘ON’, the USB Hub ports follows computer selection.
When set to ‘OFF’, the USB Hub ports stays on the currently selected
PC port.