Status instruments Sem1700 User manual

To fit or release module

Insert screw driver into

slot and lever latch

away from body

MECHANICAL INSTALLATION

Enclosure

Style DIN Rail Mount

Material Blend PC/ABS self extinguishing

Terminals Screw terminal

Cable 2.5 mm Max

Colour Gray

Ø 3 mm

MOUNTING

Screw driver

EN60715 DIN RAIL

Ambient Range

+ 70 °C Max

- 20 °C Min

Ø 3mm

Screw Driver

Shielded Cable Twisted Pair Cable TC Compensation Cable

Screened

TURN OFF SUPPLY BEFORE

WORKING ON ANY ELECTRICAL

CONNECTION

INPUT CONNECTION

For cable length < 3 Meters no shielded

cable or twist pair required.

Thermocouple inputs must use correct

compensation cable.

Pt100 inputs all three wires must be equal

length (resistance).

Max input cable length 30 meters.

Temperature Process Current

Externally

Powered

Voltage TRIP 1(A)

TRIP 2(B)

Current

Internal

Powered

ANALOG OUTPUT CONNECTION

For cable length < 3 meters no shielded cable

or twisted pair required.

Use twisted pair or shielded cable for current

output < (30 to 1000) meters.

Voltage output use shielded cables (3 to 30)

meters, cable lenghts > 30 meters not advised.

TRIP OUTPUT

CONNECTION

Trip outputs are isolated

from each other.

Max switching current 1 A

@ 240 V ac, 1 A @ 30 V dc

SUPPLY CONNECTION

Supply input is not polarity

sensitive.

Max supply 240 V ac or

240 V dc

ELECTRICAL INSTALLATION

-T/C

PT100

Slide Wire

V /mV

mA Sense

Transmitter

Load

V s

Load

9Vout

c11

a.c. d.c.

IMPORTANT- CE & SAFETYREQUIREMENTS

ThisproductissuitableforenviromentInstallationcategoryII pollutiondegree.

Theproductisclassedas"PERMANENTLYCONNECTEDEQUIPMENT".

ProductmustbeDINrailmounted,insideasuitableenclosureprovidingenvironmentalprotectiontoIP65orgreater.

DCsupplymustbederivedfromalocalsupplyandnotadistributionsystem.

Maxrelaycontactrating240VAC@1a(30VDC@1A).Anycircuitconnectedtoacontactmustbefusedwitha2A(T)fuse.

TomaintainCEEMCrequirements,inputandsupplywires mustbelessthan30meters.

Theproductcontainsnoserviceableparts,orinternaladjustments.noattemptmustbemadetorepairthisproduct.Faultyunitsmustbereturnedtosupplierforrepair.

Thisproductmustbeinstalledbyaqualifiedperson.Allelectricalwiringmustbecarriedoutinaccordancewiththeappropriateregulationsfortheplaceofinstallation.

Beforeattemptinganyelectricalconnectionwork,pleaseensureallsuppliesareswitchedoff.

ABSOLUTEMAXIMUM CONDITIONS:-

SupplyVoltage ±240Vdc ±240Vac(Protectedforovervoltage)

InputVoltage ±24V betweenanyterminals

InputCurrent ±50mAbetweenterminals

Output 30Vdc

Trips 240Vac@1A30Vdc@1A noninductive

Ambient Temperature (-4to158)°F Humidity(10to95)%RH(Noncondensing)

PRODUCT SPECIFICATION

Please refer to the product data sheet for full specification, available to down load at www.status.co.uk.

RECEIVE AND UNPACKING

Please inspect the packaging and instrument thoroughly for any signs of transit damage. If the instrument has been damaged, please notify your supplier

immediately.

CONFIGURATION

IMPORTANT During configuration the device takes its power from the USB port, therefore no power connection is required. The device can be configured while powered

but the computer used must be isolated from the mains supply earth to avoid ground loop effects.

Device

M-CONFIG or USB_LINK software

(usb_link V2.0 or greater)

USB CABLE

Disk or download @

www.statInst.com

COMPUTER

The following parameter can be configured by simply entering as prompted by the software package.

· Input type / input sensor / units(temperature inputs) / sample rate

· Scale input to process variable (process inputs only)

· Analog Output / Set Type voltage or current / scale output signal range / scale output to process

Set adjustable damping for both rising and falling output. Set correction for voltage output load.

· Trip Outputs / Set action / Set setpoints / Set deadband / Set adjustable delay on and delay off

· Set burnout direction on sensor failure or input overrange.

· Set the function of the front panel user buttons to off, trim or configure.

. TAG number

Factory default:

Input type = P

Sample rate = 1000 mS

Units = °C

Output = (4 to 20) mA damping 0

High Range = 100

Low Range = 0

Burnout = UPSCALE

User Trim = off

Trips = off, delays 0

Damping = 0

Status Instruments Inc, PO Box 548, 456 Park Avenue, Scotch Plains, NJ 07076

Web Page: www.statinst.com Tel : (800) 700-3272 Fax: (800) 700-5468 email : [email protected]

SEM1700 USER GUIDE

Temperature/Process Conditioner with

Universal input, outputs supply plus

manual config/trim.

Every effort has been taken to ensure the accuracy of this document, however we do not accept responsibility for damage, injury, loss or expense resulting from errors and omissions, and we reserve the right of amendment without notice.

Important - Please read this document before any installing.

INPUT

External Powered

(4-20) mA Output

SEM1700

Internal Powered

current Output

TRIP 1 (A)

TRIP 2 (B)

12 11 ANALOGUE OUTPUT

USB

Slide Wire

PT100

T/C

V /mV

Temperature

Process

mA Sense

Transmitter

V s

Load

TRIP OUTPUT

Vout

Voltage

OUTPUT

SUPPLY (20 to 240) V AC or DC

All Dimensions in mm

USER TRIM

Supply

User trim function allows manual adjustment of the analog output, this is useful for minor calibration adjustment or

trimming out any sensor error, ± 5 % of range adjustment is available at both offset and span. Raise and lower buttons

are provided on the front panel of the transmitter, accessed using a 3 mm flat blade screw driver. Insert the screw

driver into the appropriate slot to operate the button. The button has a click action.

The transmitter will automatically detect the correct trim point (offset or span) based on the output signal. Offset will be

trimmed when the current in the offset band, span when the current is in the span band. No trim action occurs at any

other current. Note this function needs to be selected by the software configuration tool before use. To lock settings

after adjustment the operator can again use the tool to turn this function off, (select the option to save trim when

downloading configuration).

METHOD

1.0 Connect transmitter to a suitable input simulator or sensor.

Connect supply, connecting a digital meter to monitor output.

Turn supply on, set input to offset/span calibration point.

IMPORTANT - IF PERFORMING TWO POINT CAL, ALWAYS CAL

OFFSET FIRST.

2.0 Enter trim menu by pressing "raise" button for two seconds.

When the trim menu is open the range LED will flash :-

Screw Driver Ø 3 mm

20.000

Digital mA meter

Input Simulator

or sensor

Output

Signal

offset

span

Range Offset Span

(4 to 20) mA (3.8 to 6) mA (18 to 22) mA

(0 to 20) mA (0 to 2) mA (18 to 22) mA

User mA User low ± 2 mA (Min 0 mA) User High ± 2 mA (Max 24 mA)

(0 to 10) V (0 to 1) V (9 to 11) V

UserV User low ± 1 V (Min 0 V) User High ± 1 V (Max 12 V)

Enter Green Ok LED will indicate Trim action

> 2 s

3.0 Trim output current by

pressing either the raise or

lower button, single click to

step advance, or press contin-

uously to auto advance.

4.0 Once trim is complete allow

30 seconds with no button

press, the transmitter will time

out and return to normal

operation.

Raise

Lower

Escape

> 30 s

USER RANGE CONFIGURATION

This function allows two point manual configuration of the re-transmission current (voltage) at low and high range against a live input

signal. This is useful for on-site configuration, example with a slide wire input the user manually position the slide at both low and high

position and configures the unit to operate over this range. Configuration is achieved using either the raise (span) or lower (offset)

buttons.

To operate this function it must first be selected using the software configuration tool. The operator may lock this function (once set) by

turning off the function.

METHOD

1.0 Connect transmitter to a suitable input simulator or sensor. Connect supply, turn supply on, set input to either offset or span calib-

ration point.

2.0 To enter configuration, set input to desired high or low

setting and wait 10 seconds. Press and hold raise(high) or

lower(low) button on for 2 seconds to enter.

The Ok LED will then start to flash at a slow rate (low) or fast

rate(high).

3.0 Once the menu has been entered, quickly (within 1 second)

apply a single press the the raise(high) lower(low) button to store

setting.

To abort configuration, allow configuration to time out by not

pressing buttons for 5 seconds.

Ø 3 mm

Screw Driver

Input Simulator

or sensor

Low- slow toggle

High fast toggle

Input out of range

> 2 s

Enter High scale

config

Enter Low scale

config

< 1 s Single Press

Store High scale config

Store Low scale config

Green Ok LED will indicate Trim action

BCA

18 16

TRIP 1 (A) A

15 13

TRIP 2 (B)

Action Normal Trip Range Error Power off

Hi_ Al

Lo_Al

Hi_ Con

Lo_Con

OUTPUT DAMPING

User adjustable damping of the analog output is provided for both rising and falling signal. The adjustable range is (0 to 250) second for a ( 0 to 20) mA or

(0 to 10) V swing. To calculate rate of change of output signal divide 20mA (10 V) by damping setting, example if damping is set to 100 seconds the mA

output will change at a rate of (20/100) = 0.2 mA /Second. Use USB_LINK software to configure damping setting.

TRIP OUTPUTS

Dual trip SPDT relays are available. The contacts are rated at 240 V ac 1 A (Non inductive) 30 V DC 1 A. An external snubber network is recommended when

switching inductive circuits. Please ensure the snubber network is rated for the application. Four actions are provided, as detailed in the diagram below.