Steel City 20-302 User manual

For technical support, provide the following model
and serial numbers:
Model o: ______________________
Serial o: ______________________
14’’ BAND SAW
OWNER’S ANUAL
20-302
072020

Page 2
WARRANTY
STEEL CITY WARRANTY
The manufacturer warrants its machines to be free from defects in workmanship and materials for a period of
2 years from the date of the original purchase for Steel City shop machines or for a period of 1 year for Titanium
production machines; subject to the following conditions :
A-Warranty applies to the original buyer only and may not be transferred. Original proof of purchase is
required.
B- Warranty is void if repairs or alterations are made to the machine by an unauthorized service center without
the direct consent of the manufacturer or its representative.
C- Warranty does not include defects, failures or breakages directly or indirectly caused by or resulting from
improper use, improper or lack of maintenance, abuse or misuse, negligence, accidents, damages in
handling or transportation, or normal wear and tear of any part or component.
D- Accessories and wear items such as motor, switch, bearings, drive belt or other accessories are covered
for 1 year.
E- Consumables such as blades, knives, bits, sandpaper or others are not covered.
To file a warranty claim, customer may contact his dealer or email se [email protected]
The manufacturer or its representative will inspect, repair or replace any part that has proven to be defective in
workmanship or material, provided that the customer sends the product prepaid to a designated authorized
service center and provides reasonable time to proceed.
If judged on warranty, the manufacturer or its representative will return the repaired product prepaid or will replace
it by a new one at its choice. On the contrary, if it is determined that there is no defect or that the problem resulted
from causes not within the scope of the warranty, it will dispose of or return the product at customer’s expenses,
following customer’s instructions.
The manufacturer or its representative shall not be held liable for any special, indirect, incidental, punitive or
consequential damages, including and without limitation loss of profits arising from or related to the warranty,
the breach of any agreement, the operation or the use of its machines.
Note:
The specifications in this manual are provided for informational purposes only and are subject to rectification
without notice. Some measures have been slightly rounded for ease of reading. Unless otherwise noted, they
should be considered for reference only.
Steel City reserves the right to make certain improvements to the design and appearance of its machines,
components, accessories or parts without notice and without the obligation to perform them on existing models.

Page 3
This user manual is intended for use by anyone working with this machine. It should be kept available for
immediate reference so that all operations can be performed with maximum efficiency and safety. Do not attempt
to perform maintenance or operate this machine until you have read and understand the information contained
in this manual.
The drawings, illustrations, photographs, and specifications in this user manual represent your machine at time
of print. However, changes may be made to your machine or this manual at any time with no obligation to
Steel City.
I TRODUCTIO .......................................................................................................... 3
TABLE OF CO TE TS................................................................................................ 3
PRODUCT SPECIFICATIO S ..................................................................................... 3
SAFETY........................................................................................................................ 4
PRODUCT SAFETY..................................................................................................... 6
ELECTRICAL A D GROU DI G I STRUCTIO S ................................................... 7
U PACKI G A D I VE TORY .................................................................................. 8
ASSEMBLY .................................................................................................................. 9
ADJUSTME TS ......................................................................................................... 11
MAI TE A CE ......................................................................................................... 14
PARTS LIST ............................................................................................................... 15
TABLE OF CONTENTS
INTRODUCTION
PRODUCT SPECIFICATIONS
Motor 1 HP - 110V - 1 ph - 11A (conv rtibl to 220V - 1 ph)
Motor sp d 1720 RPM
Blad sp d 2300 or 3200 lin. ft./min
Cutting capacity (h ight) 7-1/2”
Cutting capacity (width) 13-3/4”
Cast iron tabl dim nsions 14” x 14”
Tabl tilt -10° to 45°
Tabl h ight from floor 44”
Ov rall h ight 71”
Blad width (min. – max) 1/8” – 3/4”
Blad l ngth 101”
Blad guidanc Guid blocks and thrust b arings
Dust port 1 x Ø4”
Approx. w ight 95 kg
Packing dim nsions 180 x 67 x 45 cm

Page 4
All federal and state laws and any regulations having
jurisdiction covering the safety requirements for use of this
machine take precedence over the statements in this
manual. Users of this machine must adhere to all such
regulations.
Below is a list of symbols that are used to attract your
attention to possible dangerous conditions.
These are safety alert symbols. They are used to alert you
to potential personal injury hazards. Obey all safety
messages that follow these symbols to avoid possible injury
or death.
Indicates an imminently hazardous situation which, if not
avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, WILL result in serious injury or death.
Indicates a potentially hazardous situation which, if not
avoided, COULD result in serious injury or death.
Exposure to the dust created by power
sanding, sawing, grinding, drilling and other
construction activities may cause serious
and permanent respiratory or other injury,
including silicosis (a serious lung disease),
cancer, and death. Avoid breathing the dust, and avoid
prolonged contact with dust. The dust may contain
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other
masonry products.
• Arsenic and chromium from chemically-treated
lumber.
Always operate tool in well ventilated area and provide
for proper dust removal. Use a dust collection system
along with an air filtration system whenever possible.
Always use properly fitting IOSH/OSHA approved
respiratory protection appropriate for the dust exposure,
and wash exposed areas with soap and water.
DANGER
!
This manual is not totally comprehensive. It does not and can not convey every possible safety and
operational problem which may arise while using this machine. The manual will cover many of the basic
and specific safety procedures needed in an industrial environment.
ALWAYS wear eye protection. Any
machine can throw debris into the eyes
during operation, which could cause severe
and permanent eye damage. Everyday
eyeglasses are NOT safety glasses.
ALWAYS wear Safety Goggles (that comply with A SI
standard Z87.1) when operating power tools.
SAFETY
WARNING
!
ALWAYS wear hearing protection. Plain
cotton is not an acceptable protective
device. Hearing equipment should comply
with A SI S3.19 Standards.
WARNING
!
WARNING
!
WARNING
!
TO REDUCE the risk of electrical shock.
DO NOT use this machine outdoors. DO
NOT expose to rain or moisture. Store
indoors in a dry area. DO NOT handle the
plug with wet hands.
1. To avoid serious injury or damage to the machine, read
the entire User Manual before assembly and operation
of this machine.
2. Serious personal injury may occur if normal safety
precautions are overlooked or ignored. Accidents are
frequently caused by lack of familiarity or failure to pay
attention. Obtain advice from supervisor, instructor, or
another qualified individual who is familiar with this
machine and its operation.
3. STOP using this machine, if at any time you experience
difficulties in performing any operation. Contact your
supervisor, instructor or machine service center
immediately.
WARNING
!
CHILDPROOF THE WORKSHOP AREA
by removing switch keys, unplugging tools
from the electrical receptacles, and using
padlocks. DO NOT use near or around
children.
WARNING
!

Page 5
4. Prevent electrical shock. Follow all electrical and safety
codes, including the ational Electrical Code ( EC) and
the Occupational Safety and Health Regulations
(OSHA). All electrical connections and wiring should be
made by qualified personnel only.
5. ALWAYS be sure that the power switch is in the “OFF”
position and unplug the machine from the electrical
receptacle when making adjustments, changing parts or
performing any maintenance.
6. AVOID ACCIDENTAL STARTING. Make sure that the
power switch is in the “OFF” position before plugging in
the power cord to the electrical receptacle.
7. NEVER leave a machine running, unattended. Turn the
power switch to the OFF position. DO NOT leave the
machine until it has come to a complete stop.
8. THE USE of extension cords is not recommended for
220V equipment. It is better to position your equipment
and install the wiring to eliminate the need for an extension
cord. If an extension cord is necessary, refer to the chart
in the Grounding Instructions section to determine the
minimum gauge for the extension cord. The extension
cord must also contain a ground wire and plug pin.
9. DO NOT pull a machine by the power cord. NEVER
allow the power cord to come in contact with sharp
edges, hot surfaces, oil or grease.
10. DO NOT unplug a machine by pulling on the power
cord. ALWAYS grasp the plug, not the cord.
11. REPLACE a damaged cord immediately. DO NOT use
a damaged cord or plug if the machine is not operating
properly, or has been damaged, left outdoors or has
been in contact with water.
12. NEVER remove any chips without turning off the
machine and disconnecting the power.
13. NEVER turn on the machine if the workpiece is in
contact with the blade.
14. ENSURE that the machine sits firmly on the floor before
using. If the machine wobbles or is unstable, correct the
problem by using shims or blocks prior to operation.
15. ALWAYS keep hands and fingers away from the blades
when operating.
16. DO NOT USE the machine to perform an operation for
which it was not designed. It will be safer and provide
high quality job by only performing operations for which
the machine was intended.
17. Every work area is different. Always consider safety first,
as it applies to your work area. Use this machine with
caution. Failure to do so could result in serious personal
injury and damage to the machine.
18. DO NOT stand on a machine. Serious injury could result
if it tips over or you accidentally contact any moving part.
19. DO NOT store anything above or near the machine.
20. RE OVE ALL AINTENANCE TOOLS from the
immediate area prior to turning the machine O .
21. AINTAIN your balance. DO NOT extend yourself over
the tool. Wear oil resistant rubber soled shoes. Keep
floor clear of debris, grease, and wax.
22. DO NOT operate any machine or tool if under the
influence of drugs, alcohol, or medication.
23. AINTAIN all machines with care. ALWAYS KEEP
the machine clean and in good working order. KEEP all
blades and tool bits sharp and free of all rust and pitch.
24. EACH AND EVERY time, check for damaged parts prior
to using any machine. Carefully check all guards to see
that they operate properly, are not damaged, and
perform their intended functions. Check for alignment,
binding or breakage of all moving parts. Any guard or
other part that is damaged should be immediately
repaired or replaced. Check material for loose knots.
25. Safety decals are on this machine to warn and direct
you to how to protect yourself or visitors from personal
injury. These decals UST be maintained so that they
are legible. REPLACE decals that are not legible.
26. KEEP protective guards in place and in working order.
27. Check material for loose knots, nails and other defects.
28. ALWAYS keep the work area clean, well lit, and
organized. DO NOT work in an area that has slippery
surfaces. Keep floor clear of debris, grease, and wax.
29. SECURE all work. When it is possible, use clamps or
jigs to secure the workpiece. This is safer than
attempting to hold the workpiece with your hands.
30. STAY ALERT, watch what you are doing, and use
common sense when operating any machine. DO NOT
operate any machine tool while tired or under the
influence of drugs, alcohol, or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
31. USE ONLY recommended accessories. Use of incorrect
or improper accessories could cause serious injury to
the operator and cause damage to the machine. If in
doubt, DO NOT use it.
32. Wear proper clothing, DO NOT wear loose clothing,
gloves, neckties, or jewelry. These items can get caught
in the machine during operations and pull the operator
into the moving parts. Users must wear a protective
cover on their hair, if the hair is long, to prevent it from
contacting any moving parts.
33. Keep visitors and children away from any machine.
DO NOT permit people to be in the immediate work
area, especially when the machine is operating.
34. DO NOT use a machine as a toy.
35. DO NOT use electrical tools in the presence of
flammable liquids or gasses.
36. SAVE these instructions and refer to them frequently
and use them to instruct other users.
37. Establish a SAFETY ZONE around shop machinery.
A clearly defined “no-go” zone on the floor around each
machine. Take a few moments to either paint (using
non-slip paint) or using tape, define on the floor the limits
or perimeter of each machines safety zone.

Page 6
PRODUCT SAFETY
1. Replace any blade which, while rotating, has a back and
forth movement over average. Generally, a bad welding
is in cause and blades break quickly.
2. In the event of a blade break, stop the machine imme-
diately et move away to avoid any part projection. Wait
until complete wheels stop before opening the access
doors.
3. While using, do not bring your fingers any closer than
2” to the blade. Use a push stick or pull the piece from
behind the blade.
4. Get rid of the waste parts as you go, rather than letting
them fall on the floor and risk to tip over them.

Page 7
To reduce the risk of electric shock, follow all
electrical and safety codes, including the
ational Electric Code ( EC) and the
Occupational Safety and Health Regulations
(OSHA). All electrical connections and wiring
should be made by qualified personnel only.
WARNING
!
This machine UST BE GROUNDED
while in use to protect the operator from
electric shock.
WARNING
!
In the event of a malfunction or breakdown, GROUNDING
provides the path of least resistance for electric current and
reduces the risk of electric shock. The plug UST be
plugged into a matching electrical receptacle that is
properly installed and grounded in accordance with ALL
local codes and ordinances.
If a plug is provided with your machine DO NOT modify the
plug. If it will not fit your electrical receptacle, have a
qualified electrician install the proper connections to meet
all electrical codes. All connections must also adhere to all
of OSHA mandates.
I PROPER ELECTRICAL CONNECTION of the
equipment-grounding conductor can result in risk of electric
shock. The conductor with the green insulation (with or
without yellow stripes) is the equipment-grounding
conductor.
DO NOT connect the equipment-grounding conductor to a
live terminal if repair or replacement of the electric cord or
plug is necessary.
Check with a qualified electrician or service personnel if you
do not completely understand the grounding instructions,
or if you are not sure the tool is properly grounded.
INI U RECO ENDED GAUGE FOR EXTENSION CORDS (AWG)
115/230 VOLT OPERATION ONLY
25’ long 50’ long 100’ long
0 to 6 Amps 18 AWG 16 AWG 16 AWG
6 to 10 Amps 18 AWG 16 AWG 14 AWG
10 to 12 Amps 16 AWG 16 AWG 14 AWG
12 to 15 Amps 14 AWG 12 AWG ot
recommended
◊ EXTENSION CORDS
◊ PLUGS/RECEPTACLES
AKE SURE the circuit breaker does not
exceed the rating of the plug and
receptacle.
WARNING
!
To reduce the risk of fire or electrical
shock, use the proper gauge of extension
cord. When using an extension cord, be
sure to use one heavy enough to carry the
current your machine will draw.
WARNING
!
The smaller the gauge-number, the larger the diameter of
the extension cord is. If in doubt of the proper size of an
extension cord, use a shorter and thicker cord. An
undersized cord will cause a drop in line voltage resulting
in a loss of power and overheating.
WARNING
!
If you are using an extension cord outdoors, be sure it is
marked with the suffix “W-A” (“W” in Canada) to indicate
that it is acceptable for outdoor use.
Make certain the extension cord is properly sized, and in
good electrical condition. Always replace a worn or
damaged extension cord immediately or have it repaired by
a qualified person before using it.
Protect your extension cords from children, sharp objects,
excessive heat, and damp or wet areas.
USE ONLY a 3-wire extension cord that has
a 3-prong grounding plug and a 3-pole
receptacle that accepts the machine’s
plug.The third prong is used to ground the
tool and provide protection against
accidental electric shock. DO NOT remove the third.
◊ AGNETIC SAFETY SWITCH
If the machine is equipped with a magnetic safety switch
you must to reset the overload protection switch after an
overload.
1. Remove the control box cover.
2. Press the reset button.
3. Reinstall the control box cover.
ake certain that the machine is disconnected
from the power source
WARNING
!
ELECTRICAL AND GROUNDING INSTRUCTIONS

Page 8
DEGREASING
In order to prevent any corrosion during transport, an
antirust has been applied. Above all, greasy surfaces
should be wiped clean and cleaned with a clean cloth and
degreaser. Refer to the safety instructions for this type of
product. Do not use solvents such as acetone or lacquer
thinner, painted surfaces will suffer.
Unpack the machine carefully and make an inventory of the
hardware and accessories in the packaging, referring to the
list below.
Be aware of missing or damaged parts to inform your
supplier as soon as possible.
WARNING
!
This machine is heavy, more
than one person is required to
unpack and lift.
UNPACKING & INVENTORY
1. Band saw
2. Table
3. Stop paddle
4. Base – end panels
5. Base – side panels
6. Motor
7. Motor step pulley
8. Table support
9. Miter gauge
10. Hardware bags (2)
1.
2.
3.
9.
6.
4.
7. 8.
5.
10.

Page 9
ake sure the switch is in the off position and
the machine is unplugged.
◊ BASE ASSE BLY
1. Assemble the base, placing the narrow end facing the
floor (upside down) and attach the panels using the
short carriage bolts with washers and nuts.
2. Mount the plastic feet on base corners using hex bolts.
3. Return the base and put it back on its feet.
ASSE BLY
◊ SAW ASSE BLY
1. With the help of another person, install the saw on the
base and attach it to the base by using hex bolts on
each corner.
2. Install the step pulley on the motor shaft, with the largest
pulley on the motor side. Put the key in the shaft
keyway, slide the pulley in and lock it in place by
tightening the set screw.
3. Install the motor on the saw. Put the motor on the base
and slide it in place by passing the pulley into the hole
of the saw side.
4. Put the motor in position, aligning the holes of the motor
base with the slots in the saw base. Install 4 carriage
bolts with washers and nuts, but do not tighten at this
stage. Attach the motor cable to the cable connector on
the saw.
WARNING
!

Page 10
5. Open the lower access door. The drive belt is already
inside, on the saw shaft. Check if the motor pulley is in
line with the saw pulley. If required, loosen the set screw
on the motor shaft so you can slide the motor pulley to
align it with the saw pulley, and tighten the set screw to
lock in place.
6. Choose between one of the two blade speeds offered
(2300 ou 3200 lin.ft./min). Put the belt on the desired
saw pulley and move the belt onto the lower pulley while
slowly rotating the wheel to force the belt in place. Be
careful not to get your fingers pinched.
7. Slide the motor away from the wheel to tighten the belt.
Make sure the belt is tight enough so it won’t come off
or slip on the pulley. Secure the motor mount bolts back
to the saw base.
2300 F.P.M.
3200 F.P.M.
Wheel pulley
Motor pulley
Step pulleys – lower wheel removed for
clarity
◊ ATTACHING THE TABLE
1. Install the table mount on the saw frame, using 2 hex
bolts. Also install the hex bolt and nut acting as positive
stop, at shown location near the table mount.
Stop
2. With the bolts hanging free through the trunnions, guide
the blade through the slot in the table and turn the table
to guide the bolts into the openings in the table mount.
The table slot for the miter gauge must be on the right
side of the blade. With both bolts in place, install the lock
knobs to secure in position.
3. Install the red insert plate into the opening with detent
in the slot. It is possible that some filing or sanding be
required on the exterior contour of the insert to remove
some excess paint and ease its installation.

◊ BLADE TRACKING
1. Turn the upper wheel by hand to check blade tracking
on the wheel tires. Blade should be relatively centered
on both upper and lower wheels.
2. To adjust blade tracking, loosen the lock nut behind the
tracking adjustment knob, located behind the upper
panel.
Page 11
◊ BLADE REPLACE ENT
1. Release blade tension by lifting blade tension handle.
It might be necessary to turn the handle counterclock-
wise for the blade to be loose enough to be removed
easily. Do not ove loosen blade tension mechanism
to avoid disconnecting the tension.
2. Remove the table alignment pin from the table slot.
3. Remove the table insert and open both access doors.
4. Move the upper and lower guide blocks and thrust
bearings away from the blade.
5. Remove the blade by pulling the left side first and then
slide the right side through the table slot. Be careful not
to have the teeth rubbing against metallic surfaces.
Wea ing safety glasses and gloves is
ecommended.
6. Working the reverse steps, install the replacement blade.
Make sure the teeth are facing down on the right side of
the wheel. Reinstall the alignment pin in the table slot.
◊ BLADE TENSION
1. With the blade positioned in the center of the wheels,
lower the tension handle. The handle is excentrically
mounted to generate blade pull effect and compresses
the tension spring.
To increase the tension, turn the lever (in vertical
position) in clockwise direction. To reduce tension, turn
in counterclockwise direction. Lower handle to apply
tension and check if setting is appropriate. Neve tu n
the tension handle while it is in downwa d position,
as you may b eak the tension sp ing.
Increase
tension Reduce
tension
To prolong the life of the blade and the spring, if the
bandsaw is not in use for an extended period of time
(over 24 hrs), release the blade tension by lifting the
handle and disconnect power.
ADJUST ENTS
We will do a blade replacement to show the various
adjustments required.
2. Move the upper guide block assembly to its highest
point.
3. With the saw turned off, check tension by pressing
against the side of the blade, halfway between the guide
block and the table. The blade should not flex more than
about 2 mm (5/64’’).
OTE : Too much tension will make the blade break
prematurely and will be more difficult to use for tight radius
cuts. With insufficient tension, the blade will have tendency
to drift when cutting, might slip on the lower wheel so blade
stops cutting and will give poor cut quality.
To move the blade toward the inside, turn the knob
clockwise. To move the blade toward the outside, turn the
knob counter clockwise. Turn the wheel by hand to move
the blade and confirm the tracking. Lock the knob in
position by tightening the lock nut.
ake sure the switch is in the off position and
the machine is unplugged.
WARNING
!
Clockwise
direction
Counter-
clockwise
direction

◊ CHANGING BLADE SPEED
We offer 2 blade speeds, low and high (2300 or 3200
lin.ft./min).
1. Open the lower door to access the wheel.
2. Move the belt on the set of pulleys corresponding to the
chosen low or high speed.
3. Motor can be slid to ease the speed change; loosen the
motor base bolts so you can slide the motor and remove
belt tension. After speed change, slide the motor back
to tension the belt (approx. 1/4’’ deflection at midpoint)
and tighten the motor base bolts.
◊ SQUARING UP THE TABLE
The table default position must be set to 90° to the
blade and the angle indicator set to 0°, to allow quick
adjustment for square cuts and angled cuts. An
hexagonal bolt with a lock nut makes this positive stop
and requires adjustment, so the table is at 90° to the
blade:
1. Loosen the 2 lock knobs under the table.
2. Place a combination square flat on the table with the
heel of the square flat against the blade.
3. Adjust the positive stop so the table is at 90° to the
blade. Tighten the lock nut. This may take a few trials
to obtain squareness. Tighten the lock knobs.
4. Adjust the pointer to read 0° on the angle indicator.
Page 12
◊ BLADE GUIDANCE AND CUTTING
HEIGHT
Both the upper and lower guide block assemblies must
be adjusted after each blade replacement and after
each blade tracking adjustment.
Also, the upper guide block assembly must be adjusted
to be about 1/8’’ (3 mm) above the piece. Minimum
amount of blade should be exposed.
With one hand, loosen the knob securing the assembly
in position and with the other hand, raise or lower the
guide block assembly to the proper height.
The friction blocks on each side of the blade must be
adjusted so they are behind the hollowed part of the
teeth, and be close to the side of the blade without
touching it (by the thickness of a sheet of paper). The
upper and lower thrust bearings must also be adjusted
so they barely touch the blade (1/64” behind the blade).
Blade guard removed for
clarity
NOTE: Both upper and lower guide blocks and
bearing assemblies must be adjusted so they
barely touch the blade. When the saw is running
free, no block or bearing is used, but when
cutting starts they maintain the blade.
The part of block or bearing almost in contact
with the blade must be parallel to the blade and
by no way touch the teeth of the blade.
Stop Lock knob Pointer
5. It is possible to tilt the table to the left, up to an angle of
about -10°. You need to remove the table positive stop
(the hex bolt). Do not forget to reinstall the positive stop
when you are done and check squareness of the table
to the blade.
3200 F.P.M.
Wheel pulley
Motor pulley
Step pulleys – Wheel removed
for clarity
2300 F.P.M.

◊ ITER SLOT PARALLELIS
The miter slot must be parallel to the blade as much as
possible. This allows the miter gauge to slide parallel to
the blade so you get some precision on miter cuts.
This adjustment is easier if we use the widest allowable
blade for the saw.
1. Install the widest blade and loosen the 6 bolts holding
the trunnions in place under the table.
2. Place a straightedge near the blade, so it is parallel to
the slot. It must be touching evenly from front to back
without moving the blade and without resting on a tooth
of the blade.
3. Measure the distance from the straightedge to the miter
slot at each end of the table.
If these measurements are not equal, slightly rotate the
table to correct, realign the straightedge with the blade
and take measurements again from the miter slot to the
straightedge, at each end of the table.
4. When both measurements are equal, tighten the
6 trunnion bolts. Be careful not to move the table when
you tighten the bolts.
Page 13
NOTE : This process will get the miter slot close
to being parallel with the blade, improving angled
cuts precision, but still will not be totally
accurate.
This is due to other factors, namely blade drift or
blade lead,
that cannot be totally eliminated.

Page 14
DUST COLLECTION
Using this machine without dust collection may
cause premature wear, but also represent a
health hazard for the user and for the other
people in the workshop.
STARTINGORDER:
Start: start the dust collector, then the saw.
Stop: stop the saw, then the dust collector.
The saw is equipped with a dust port located at the bottom
of the saw casing and provides a Ø4’’ connection.
AINTENANCE
◊ CLEANING AND LUBRICATION
- All bearings are sealed and life lubricated and do not
require additional maintenance, except replacement
eventually.
- Blow dust away and clean the saw frequently,
especially the blade guide blocks and bearings
to prevent build up of pitch, resin, etc.
When accumulation of dirt resists to normal dusting:
- Clean with the use of a soft solvent (do not use
acetone or lacquer thinner)
- Lubricate using lubricant for dusty environment
Threaded parts and mobile parts should be inspected,
cleaned and lubricated regularly to prevent
malfunctioning.
◊ DRIVE BELT REPLACE ENT
1. Release blade tension.
2. Remove the blade.
3. Remove the nut and washer from the center of the
wheel.
Untighten the nut by turning in clockwise direction.
◊ CLEANING BRUSH
A cleaning brush is installed to prevent pitch and saw-
dust build up on the lower wheel. Verify that the brush
keeps the lower wheel tire clean at all times. It will wear
over time and will not clean as well, you must then re-
place it.
4. Remove the wheel. You now have access to the belt.
5. Loosen the motor base bolts to slide the motor
and release belt tension.
6. Remove the belt and install the new one.
7. Do the above steps in reverse order. Make all
adjustments related to blade change.
ake sure the switch is in the off position and
the machine is unplugged.
WARNING
!
WARNING
!

Page 15
PARTS LIST

Page 16

Page 17

Page 18
!"#$#"%#%
!"#$#"%#"
!"#$#"%#$
!"#$#"%#&
!"#$#"%#'
!"#$#"%#(
!"#$#"%#)
!"#$#"%#*
!"#$#"%#+
!"#$#"%%#
!"#$#"%%%
!"#$#"%%&
!"#$#"%%'
!"#$#"%%(
!"#$#"%%)
!"#$#"%%*
!"#$#"%%+
!"#$#"%"#
!"#$#"%"%
!"#$#"%""
!"#$#"%"$
!"#$#"%"&
!"#$#"%"'
!"#$#"%"(
!"#$#"%")
!"#$#"%"),
!"#$#"%"*
!"#$#"%"+
!"#$#"%$#
!"#$#"%$%
!"#$#"%$"
!"#$#"%$$
!"#$#"%$&
!"#$#"%$&-
!"#$#"%$&
!"#$#"%$'
!"#$#"%$(
!"#$#"%$)
!"#$#"%$*
!"#$#"%+#
!"#$#"%+%
!"#$#"%+"
!"#$#"%+$
!"#$#"%++
!"#$#"%+&
!"#$#"%+'
!"#$#"%+(
!"#$#"%+)
!"#$#"%+*
!"#$#"%&#
!"#$#"%&"
!"#$#"%&",
!"#$#"%&$
!"#$#"%&+
!"#$#"%&&
!"#$#"%&'
!"#$#"%&(
!"#$#"%&)
!"#$#"%'#
!"#$#"%'%
!"#$#"%'+
!"#$#"%'',
!"#$#"%'),
!"#$#"%'*
!"#$#"%("
!"#$#"%(+
!"#$#"%(&

Page 19
!"#$#""#%
!"#$#""%&
!"#$#""%'
!"#$#""%(
!"#$#"""%
!"#$#"$#%
!"#$#"$#$
!"#$#"$#)
!"#$#"$#*
!"#$#"$#+
!"#$#"$%#
!"#$#"$%%
!"#$#"$%"
!"#$#"$%$
!"#$#"$%'
!"#$#"$%(
!"#$#"$"&
!"#$#"$"'
!"#$#"$"(
!"#$#"$"+
!"#$#"$$#
!"#$#"$$"
!"#$#"%#&
!"#$#"%#"
!"#$#"%#$
!"#$#"%#'
!"#$#"%#(
!"#$#"%#)
!"#$#"%#*
!"#$#"%#+
!"#$#"%#,
!"#$#"%&&
!"#$#"%&)
!"#$#"%&*
!"#$#"%&+

Page 20
uNOTES u