Steel City 20-400 User manual

15” BAND SAW
OWNER’S GUIDE
20-400
For technical support, provide the following model
and serial numbers:
Model No: ______________________
Serial No: ______________________
012020

Page 2
WARRANTY
STEEL CITY WARRANTY
The manufacturer warrants its machines to be free from defects in workmanship and materials for a period of
2 years from the date of the original purchase for Steel City shop machines or for a period of 1 year for Titanium
production machines; subject to the following conditions :
A- Warranty applies to the original buyer only and may not be transferred. Original proof of purchase is
required.
B- Warranty is void if repairs or alterations are made to the machine by an unauthorized service center without
the direct consent of the manufacturer or its representative.
C- Warranty does not include defects, failures or breakages directly or indirectly caused by or resulting from
improper use, improper or lack of maintenance, abuse or misuse, negligence, accidents, damages in
handling or transportation, or normal wear and tear of any part or component.
D- Accessories and wear items such as motor, switch, bearings, drive belt or other accessories are covered
for 1 year.
E- Consumables such as blades, knives, bits, sandpaper or others are not covered.
To file a warranty claim, customer may contact his dealer or email [email protected]
The manufacturer or its representative will inspect, repair or replace any part that has proven to be defective in
workmanship or material, provided that the customer sends the product prepaid to a designated authorized
service center and provides reasonable time to proceed.
If judged on warranty, the manufacturer or its representative will return the repaired product prepaid or will replace
it by a new one at its choice. On the contrary, if it is determined that there is no defect or that the problem resulted
from causes not within the scope of the warranty, it will dispose of or return the product at customer’s expenses,
following customer’s instructions.
The manufacturer or its representative shall not be held liable for any special, indirect, incidental, punitive or
consequential damages, including and without limitation loss of profits arising from or related to the warranty,
the breach of any agreement, the operation or the use of its machines.
Note:
The specifications in this manual are provided for informational purposes only and are subject to rectification
without notice. Some measures have been slightly rounded for ease of reading. Unless otherwise noted, they
should be considered for reference only.
Steel City reserves the right to make certain improvements to the design and appearance of its machines,
components, accessories or parts without notice and without the obligation to perform them on existing models.

Page 3
This user manual is intended for use by anyone working with this machine. It should be kept available
for immediate reference so that all operations can be performed with maximum efficiency and safety.
Do not attempt to perform maintenance or operate this machine until you have read and understand the
information contained in this manual.
The drawings, illustrations, photographs, and specifications in this user manual represent your machine
at time of print. However, changes may be made to your machine or this manual at any time with no
obligation to Steel City.
INTRODUCTION .......................................................................................................... 3
PRODUCT SPECIFICATIONS ..................................................................................... 3
SAFETY........................................................................................................................ 4
ELECTRICAL AND GROUNDING INSTRUCTIONS.................................................... 7
UNPAC ING AND INVENTORY .................................................................................. 8
ASSEMBLY .................................................................................................................. 9
ADJUSTMENTS ......................................................................................................... 12
MAINTENANCE ......................................................................................................... 16
PART LISTS ............................................................................................................... 17
INTRODUCTION
Motor 1,75 HP - 110V - 14A
Flywh l sp ds 575 or 905 RPM
Blad sp ds 2250 or 3550 lin. ft./min
Maximum cutting h ight 11 3⁄4”
Maximum width 14 5⁄8”
Blad dim nsions 1⁄4” to 3⁄4”
Tabl dim nsion 20” x 15 7⁄8”
Work h ight 39 1⁄4”
Tabl tilt -10° to 45°
Max. cl aranc b tw n
guid (l ft) and blad 12 3⁄4”
Max. cl aranc b tw n
guid (right) and blad 17 5⁄8”
Shipping w ight 365 lb (165 kg)
TABLE OF CONTENTS
PRODUCT SPECIFICATIONS

Page 4
All federal and state laws and any regulations having
jurisdiction covering the safety requirements for use of this
machine take precedence over the statements in this
manual. Users of this machine must adhere to all such
regulations.
Below is a list of symbols that are used to attract your
attention to possible dangerous conditions.
These are safety alert symbols. They are used to alert you
to potential personal injury hazards. Obey all safety
messages that follow these symbols to avoid possible injury
or death.
Indicates an imminently hazardous situation which, if not
avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, COULD result in death or serious injury.
Exposure to the dust created by power
sanding, sawing, grinding, drilling and other
construction activities may cause serious
and permanent respiratory or other injury,
including silicosis (a serious lung disease),
cancer, and death. Avoid breathing the dust, and avoid
prolonged contact with dust. The dust may contain
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other
masonry products.
• Arsenic and chromium from chemically-treated
lumber.
Always operate tool in well ventilated area and provide
for proper dust removal. Use a dust collection system
along with an air filtration system whenever possible.
Always use properly fitting NIOSH/OSHA approved
respiratory protection appropriate for the dust exposure,
and wash exposed areas with soap and water.
DANGER
!
This manual is not totally comprehensive. It does not and can not convey every possible safety and
operational problem which may arise while using this machine. The manual will cover many of the basic
and specific safety procedures needed in an industrial environment.
ALWAYS wear eye protection. Any
machine can throw debris into the eyes
during operation, which could cause severe
and permanent eye damage. Everyday
eyeglasses are NOT safety glasses.
ALWAYS wear Safety Goggles (that comply with ANSI
standard Z87.1) when operating power tools.
SAFETY
WARNING
!
ALWAYS wear hearing protection. Plain
cotton is not an acceptable protective
device. Hearing equipment should comply
with ANSI S3.19 Standards.
WARNING
!
WARNING
!
WARNING
!
TO REDUCE the risk of electrical shock.
DO NOT use this machine outdoors. DO
NOT expose to rain or moisture. Store
indoors in a dry area. DO NOT handle the
plug with wet hands.
1. To avoid serious injury or damage to the machine, read
the entire User Manual before assembly and operation
of this machine.
2. Serious personal injury may occur if normal safety
precautions are overlooked or ignored. Accidents are
frequently caused by lack of familiarity or failure to pay
attention. Obtain advice from supervisor, instructor, or
another qualified individual who is familiar with this
machine and its operation.
3. STOP using this machine, if at any time you experience
difficulties in performing any operation. Contact your
supervisor, instructor or machine service center
immediately.
WARNING
!
CHILDPROOF THE WORKSHOP AREA
by removing switch keys, unplugging tools
from the electrical receptacles, and using
padlocks. DO NOT use near or around
children.
WARNING
!

Page 5
4. Prevent electrical shock. Follow all electrical and safety
codes, including the National Electrical Code (NEC) and
the Occupational Safety and Health Regulations
(OSHA). All electrical connections and wiring should be
made by qualified personnel only.
5. ALWAYS be sure that the power switch is in the “OFF”
position and unplug the machine from the electrical
receptacle when making adjustments, changing parts or
performing any maintenance.
6. AVOID ACCIDENTAL STARTING. Make sure that the
power switch is in the “OFF” position before plugging in
the power cord to the electrical receptacle.
7. NEVER leave a machine running, unattended. Turn the
power switch to the OFF position. DO NOT leave the
machine until it has come to a complete stop.
8. THE USE of extension cords is not recommended for
230V equipment. It is better to position your equipment
and install the wiring to eliminate the need for an extension
cord. If an extension cord is necessary, refer to the chart
in the Grounding Instructions section to determine the
minimum gauge for the extension cord. The extension
cord must also contain a ground wire and plug pin.
9. DO NOT pull a machine by the power cord. NEVER
allow the power cord to come in contact with sharp
edges, hot surfaces, oil or grease.
10. DO NOT unplug a machine by pulling on the power
cord. ALWAYS grasp the plug, not the cord.
11. REPLACE a damaged cord immediately. DO NOT use
a damaged cord or plug if the machine is not operating
properly, or has been damaged, left outdoors or has
been in contact with water.
12. NEVER remove any chips without turning off the
machine and disconnecting the power.
13. NEVER turn on the machine if the workpiece is in
contact with the blade.
14. ENSURE that the machine sits firmly on the floor before
using. If the machine wobbles or is unstable, correct the
problem by using shims or blocks prior to operation.
15. ALWAYS keep hands and fingers away from the blades
when operating.
16. DO NOT USE the machine to perform an operation for
which it was not designed. It will be safer and provide
high quality job by only performing operations for which
the machine was intended.
17. Every work area is different. Always consider safety first,
as it applies to your work area. Use this machine with
caution. Failure to do so could result in serious personal
injury and damage to the machine.
18. DO NOT stand on a machine. Serious injury could result
if it tips over or you accidentally contact any moving part.
19. DO NOT store anything above or near the machine.
20. REMOVE ALL MAINTENANCE TOOLS from the
immediate area prior to turning the machine ON.
21. MAINTAIN your balance. DO NOT extend yourself over
the tool. Wear oil resistant rubber soled shoes. eep
floor clear of debris, grease, and wax.
22. DO NOT operate any machine or tool if under the
influence of drugs, alcohol, or medication.
23. MAINTAIN all machines with care. ALWAYS KEEP
the machine clean and in good working order. KEEP all
blades and tool bits sharp and free of all rust and pitch.
24. EACH AND EVERY time, check for damaged parts prior
to using any machine. Carefully check all guards to see
that they operate properly, are not damaged, and
perform their intended functions. Check for alignment,
binding or breakage of all moving parts. Any guard or
other part that is damaged should be immediately
repaired or replaced. Check material for loose knots.
25. Safety decals are on this machine to warn and direct
you to how to protect yourself or visitors from personal
injury. These decals MUST be maintained so that they
are legible. REPLACE decals that are not legible.
26. KEEP protective guards in place and in working order.
27. Check material for loose knots, nails and other defects.
28. ALWAYS keep the work area clean, well lit, and
organized. DO NOT work in an area that has slippery
surfaces. eep floor clear of debris, grease, and wax.
29. SECURE all work. When it is possible, use clamps or
jigs to secure the workpiece. This is safer than
attempting to hold the workpiece with your hands.
30. STAY ALERT, watch what you are doing, and use
common sense when operating any machine. DO NOT
operate any machine tool while tired or under the
influence of drugs, alcohol, or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
31. USE ONLY recommended accessories. Use of incorrect
or improper accessories could cause serious injury to
the operator and cause damage to the machine. If in
doubt, DO NOT use it.
32. Wear proper clothing, DO NOT wear loose clothing,
gloves, neckties, or jewelry. These items can get caught
in the machine during operations and pull the operator
into the moving parts. Users must wear a protective
cover on their hair, if the hair is long, to prevent it from
contacting any moving parts.
33. eep visitors and children away from any machine.
DO NOT permit people to be in the immediate work
area, especially when the machine is operating.
34. DO NOT use a machine as a toy.
35. DO NOT use electrical tools in the presence of
flammable liquids or gasses.
36. SAVE these instructions and refer to them frequently
and use them to instruct other users.
37. Establish a SAFETY ZONE around shop machinery.
A clearly defined “no-go” zone on the floor around each
machine. Take a few moments to either paint (using
non-slip paint) or using tape, define on the floor the limits
or perimeter of each machines safety zone.

Page 6
1. Replace any blade that, when rotating, has a more
pronounced forward-to-back motion than average.
Generally, welding is involved and these blades break
quickly.
2. In case of damage to the blade, turn off the machine and
move away to avoid any projections. Wait for the wheels
to stop before opening the covers.
PRODUCT SAFETY
3. Do not get your fingers closer than 2 " to the blade. Use
a pusher or pull the wood from the back of the blade.
4. Discard the wood scraps as you go, rather than letting
them fall to the floor and slide over them.

Page 7
To reduce the risk of electric shock, follow all
electrical and safety codes, including the
National Electric Code (NEC) and the
Occupational Safety and Health Regulations
(OSHA). All electrical connections and wiring
should be made by qualified personnel only.
WARNING
!
This machine MUST BE GROUNDED
while in use to protect the operator from
electric shock.
WARNING
!
In the event of a malfunction or breakdown, GROUNDING
provides the path of least resistance for electric current and
reduces the risk of electric shock. The plug MUST be
plugged into a matching electrical receptacle that is
properly installed and grounded in accordance with ALL
local codes and ordinances.
If a plug is provided with your machine DO NOT modify the
plug. If it will not fit your electrical receptacle, have a
qualified electrician install the proper connections to meet
all electrical codes. All connections must also adhere to all
of OSHA mandates.
IMPROPER ELECTRICAL CONNECTION of the
equipment-grounding conductor can result in risk of electric
shock. The conductor with the green insulation (with or
without yellow stripes) is the equipment-grounding
conductor.
DO NOT connect the equipment-grounding conductor to a
live terminal if repair or replacement of the electric cord or
plug is necessary.
Check with a qualified electrician or service personnel if you
do not completely understand the grounding instructions,
or if you are not sure the tool is properly grounded.
MINIMUM RECOMMENDED GAUGE FOR EXTENSION CORDS (AWG)
115/230 VOLT OPERATION ONLY
25’ long 50’ long 100’ long
0 to 6 Amps 18 AWG 16 AWG 16 AWG
6 to 10 Amps 18 AWG 16 AWG 14 AWG
10 to 12 Amps 16 AWG 16 AWG 14 AWG
12 to 15 Amps 14 AWG 12 AWG Not
recommended
◊ EXTENSION CORDS
◊ PLUGS/RECEPTACLES
MAKE SURE the circuit breaker does not
exceed the rating of the plug and
receptacle.
WARNING
!
To reduce the risk of fire or electrical
shock, use the proper gauge of extension
cord. When using an extension cord, be
sure to use one heavy enough to carry the
current your machine will draw.
WARNING
!
The smaller the gauge-number, the larger the diameter of
the extension cord is. If in doubt of the proper size of an
extension cord, use a shorter and thicker cord. An
undersized cord will cause a drop in line voltage resulting
in a loss of power and overheating.
WARNING
!
If you are using an extension cord outdoors, be sure it is
marked with the suffix “W-A” (“W” in Canada) to indicate
that it is acceptable for outdoor use.
Make certain the extension cord is properly sized, and in
good electrical condition. Always replace a worn or
damaged extension cord immediately or have it repaired by
a qualified person before using it.
Protect your extension cords from children, sharp objects,
excessive heat, and damp or wet areas.
USE ONLY a 3-wire extension cord that has
a 3-prong grounding plug and a 3-pole
receptacle that accepts the machine’s
plug.The third prong is used to ground the
tool and provide protection against
accidental electric shock. DO NOT remove the third.
◊ MAGNETIC SAFETY SWITCH
If the machine is equipped with a magnetic safety switch
you must to reset the overload protection switch after an
overload.
1. Remove the control box cover.
2. Press the reset button.
3. Reinstall the control box cover.
Make certain that the machine is disconnected
from the power source
WARNING
!
ELECTRICAL AND GROUNDING INSTRUCTIONS

Page 8
DEGREASING
In order to prevent any corrosion during transport, an
antirust has been applied. Above all, greasy surfaces
should be wiped clean and cleaned with a clean cloth and
degreaser. Refer to the safety instructions for this type of
product. Do not use solvents such as acetone or lacquer
thinner, painted surfaces will suffer.
Note: any greasy substance can cause adhesion problems
when applying finishing products.
Unpack the machine carefully and make an inventory of the
hardware and accessories in the packaging, referring to the
list below.
Be aware of missing or damaged parts to inform your
supplier as soon as possible.
This machine is heavy, more
than one person is required to
unpack and lift.
Front square fixture
2X
Back square fixture
2X
Graduated tape
1X
Cast table
1X
Resaw column
1X
Miter guide
1X
«d» profile
1X
Storage box
1X
Blade for hook
1X
Square profile
1X
Blade insert
1X
Rip guide
1X
Hexagonal head screw
2X
Hexagonal bolt
4X
Handle screw
4 X
Washer
4X
Lock washer
4X
Square nut
4X
Allen key
3X
Hexagonal head screw
4X
Hexagonal head screw
4X
Handle nut
2X
THE machine
1X
Brake pedal
1X
UNPACKING & INVENTORY
WARNING
!

Page 9
Make sure the switch is in the off position and
the machine is unplugged.
◊ DESASSEMBLING THE BLADE
1. Unlock each of the protective covers and loosen the
clamping handles.
2. Remove the tension on the blade by raising the
eccentric lever upward.
3. Remove the blade by passing it through the left and right
guard and taking care to avoid contact of the blade teeth
with the metal.
2. Place the table on the trunnions taking care to insert the
threaded rods of the table into the holes in the trunnions.
Trunnions
Passage
holes
Threaded
rods
3. Screw a handle nut onto each of the threaded rods now
protruding from the trunnions.
◊ TABLE
1. Remove the bolt located on the rear compass of the
machine frame.
4. Under the table is already fixed an L-shaped angle with
a passage hole.
Bolt to be
removed
ASSEMBLY
WARNING
!

Page 10
5. Align the compass’s passage hole from step 1 with the
passage hole in the bracket and insert the bolt removed
in step 1.
◊ PEDAL
1. Remove the 2 bolts located on the emergency brake
lever.
2. Insert the pedal arm into the slot located on the right
side. Attach the arm and lever together using the bolts
removed in step 1. Tighten the pan bolts securely.
◊ PARALLEL GUIDE
1. Using two hex bolts, two lockwashers and two washers,
assemble the two L-brackets at the front of the table.
Hand tighten for the moment.
2. Place a square nut on the holes of the brackets and
screw a handle screw from below.
3. Slide the T-slot located under the «d» profile into the
square nut of each of the two flanges. Press the profile
in d down and towards the table. Tighten both handles.
4. Using two hex screws, two lock washers, and two
washers, assemble the two L-brackets at the back of the
table. Hand tighten for the moment.
5. Insert a screw with a washer from underneath the
brackets. Screw in the last two square nuts.
7. Remove the parallel guide on the table so that the ball
bearings roll on the «d» profile.

Page 11
The bottom of the guide should not rub on the cast iron
table. Three points consisting of the two ball bearings
and the plastic cylinder must be the only points of
support. A slight gap with the underside of the guide is
desirable. The brackets attached to the cast iron table
allow this adjustment.
8. Adjust the height of the two profiles so that the guide
slides from left to right keeping a gap with the table.
Finally tighten the 4 screws fixing the 4 brackets.
Plastic Cylinder
A gap between the
table and the guide
A gap between the
table and the guide
◊ STORAGE
Unscrew the 4 screws on the frame and attach the hook
and the box.
◊ BLADE INSERT
Place the blade insert into the recess in the cast iron
table.
The graduated tape must be glued to the upper groove
of the «d» profile. The profile can be moved to the right
or to the left, it is advisable to work with the saw to see
the most frequent position of the profile.
9. This being done, press the guide against the blade and
stick the ribbon in the groove, the zero of the ribbon
aligned with the cursor of the indicator
◊ RIP COLUMN
1. Lightly screw 2 nuts with 2 small screws.
2. Insert the assembled bolts at 1 on each side of the rip
column.
3. Slide the nuts at the end of the guide into its lateral
groove.
4. Lock in the desired location by tightening the handles.

Page 12
◊ BLADE CHANGE
We will take the example of a blade change to illustrate
all the settings related to it.
1. Reassemble the eccentric lever.
2. Remove the safety pin and open the protective covers.
Make sure the switch is in the off position and
the machine is unplugged
3. Remove the blade,
carefully avoiding rubbing
the teeth on the metal
surfaces.
4. Insert the new blade.
Point the teeth down to
the right of the ribbon.
Replace the pin.
To increase the tension, turn the lever (in the vertical
position) clockwise. To decrease it, turn
counterclockwise.
Flip the lever down to see the correct setting of the
tension on the scale.
◊ BLADE TENSION
1. Lower the tension lever of the blade and evaluate the
tension exerted found on the scale located behind the
high wheel
Increase the
tension
Decrease the
tension
2. Rotate the wheel by hand to
observe the centering of the blade
on the wheel’s rubber.
Counter screw Handle centering the
blade.
◊ CENTER THE BLADE
1. Loosen the lock nut of the handle located on the back
at the same height as the center of the high wheel.
To spare the tensioning spring, when the saw is not in
use, remove the tension and lock the power supply.
2. Clear the ensemble of the ball bearing from the two
guiding devices located above and below the table.
To move the blade into the
frame, turn the handle clockwise.
To move it out, turn counter-
clockwise.
ADJUSTMENTS
WARNING
!

Page 13
Make sure the switch is in the off position and
the machine is unplugged.
◊ GUIDING OF THE BLADE
Torwards the exterior
of the frame
Torwards the interior
of the fram
3. To lock the adjustment, hold the handle with one hand
and tighten the locknut firmly with the other hand.
In order to understand better, the front guard has been
removed.
Rear bearing
lock
Locking the depth
adjustment of the
lateral bearings.
Rear
bearing
Lateral
bearings
Locking lateral
adjustment of lateral
bearings.
Eccentric adjustment of
the lateral bearings
Rear bearing
lock
Locking the depth
adjustment of the
lateral bearings.
Rear bearing
Lateral
bearings
Locking lateral
adjustment of lateral
bearings.
Eccentric adjustment of
the lateral bearings
Taking note of the note above, adjust all the bearings so
that they brush against the blade without touching it.
Locking the left side
bearing. Same for the
guiding device located
under the table.
Make sure all locking screws are properly tightened.
Refit the light plate and close the protective covers.
NOTE: The set of ball bearings and plastic block
of the two guiding devices must be set to almost
touch the blade. Thus, when the machine runs
empty, neither the bearings nor the blocks are
solicited, but as soon as a sawing is in progress,
they are.
The walls of the blocks and bearings in close
contact with the blade must be parallel to it and
completely clear the sawing teeth.
The bearings must not
interfere with the setting
of the teeth.
The bearings must
touch the blade
without touching it.
WARNING
!

Page 14
◊ TABLE S UARING
A hexagon bolt fitted with a counter nut is the stop for
quickly adjusting the table to 90 ° relative to the blade.
1. Disengage all ball bearings to eliminate interference.
2. Loosen the locknut of the stopper.
3. Loosen the rear compass lock handle.
4. Loosen the two handles located under the roundabouts
of the table.
◊ FRE UENCY OF ROTATION
2 rotation frequencies are possible. The choice of a
frequency is defined by the type of material.
Material harder, thicker = reduced rotation frequency.
Material softer, thinner = higher rotation frequency.
1. Eliminate belt tension: loosen the knob, raise the engine
and tighten the knob.
2. Rotate the belt and move it to transfer it into the proper
V-groove on both the drive pulley and the lower wheel.
575 RPM
905 RPM
Controller
3. Retension the belt and lock the engine with the handle.
5. Depending on the clearance between the blade and the
bracket, tighten or loosen the screw that serves as a
squareness stop.
6. When the squareness satisfies you, lock the height of
the stopper by tightening the lock nut.

Page 15
◊ CAPACITY OF SAWING HEIGHT
1. Unlock the handle.
2. Turn the handle to adjust the height of the guide device
and lock the handle.
Locking knob
Adjusting Wheel
To adjust the indicator
on the scale, unscrew
the screw. Move the
indicator to its position
and tighten the screw.
◊ EMERGENCY BREAK
In an emergency, firmly press the emergency brake
pedal. By pressing the brake, the power supply will be
automatically cut off.
◊ STARTING
- When the machine is turned on, a warning light
indicates this.
- To disengage the stop button: turn the stop button
clockwise, it will expel itself (pop!).
- To start, press the power button.
On
indicator
light
Reset
Off ◊ RESET
If the engine overheats, the power supply will be
automatically shut off to save the engine.
1. Wait for the engine to cool down.
2. Push the stop button completely.
3. Check that the correct blade is used (fewer teeth = less
friction = less effort).
4. Check that the motor ventilation grille is clear and the
inside of the machine frame is properly dusted.
4. Press the reset button located on the control panel.
5. Remove the detent and restart the machine.
◊ CLEANING BRUSH
In order to maintain the adhesion between the drive
wheel rubber and the saw blade, a cleaning brush
permanently cleans the rubber when the wheel rotates.
As and when the hairs wear, it will
move the comb accordingly.
1. Unscrew the round head screw.
2. Move the comb
3. Tighten the screw.
ADJUSTMENTS

Page 16
◊ LUBRIFICATION
- All ball bearings are lubricated and sealed for life and
require no additional maintenance except for their
possible replacement.
- Dust and clean the machine frequently, especially the
blade guide bearings.
As soon as an accumulation of dirt resists dusting:
- Clean with a mild solvent (proscribe acetone and
lacquer thinner)
- Lubricate with a lubricant for dusty environment.
All threaded parts and moving parts of the mechanisms
should be inspected, cleaned and lubricated regularly
to prevent malfunctions.
DUST CAPTURE
Using this machine without dust collection
equipment can cause premature wear of the ma-
chine, but also health problems for the user and
others working in the workshop.
ORDER OF THE START-UP:
On: Start the dust collector and then the machine.
Stop: Stop the machine and then the dust collector.
◊REPLACING THE BELT
1. Remove the blade tension.
2. Remove the blade.
3. Remove the nut and washer. Loosen by turning
clockwise.
Make sure the switch is in the off position and
the machine is unplugged.
4. Remove the wheel.
Handle
5. Remove the motor voltage.
◊ CLEANING BRUSH
When the cleaning brush has reached the end of its life,
purchase a replacement.
5. Remove the belt and install the new one.
6. Repeat the steps in reverse.
MAINTENANCE
WARNING
!
WARNING
!

Page 17
PART LISTS

Page 18

Page 19
PART LISTS

Page 20