Steelcase Opus User manual

Opus™ Sloped Fascia
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2015 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
®
Page 1 of 8
939500295 Rev E
3/16" Drill

Page 2 of 8
939500295 Rev E
Installing the Units
1. Lay units onto saw
horses. Peal paper backing
from pad (1a). Place pad
onto back of base assembly
as shown (1b). Cut excess
pad when finished.
1a
1b
PAPER
BACKING
PAD

Page 3 of 8
939500295 Rev E
2. Place the sloped end panel on a clean, abrasive
resistant surface. Place the base assembly on it's side
as shown.
3. Align the aluminum extrusion with the sloped end panel.
2
3
SLOPED END PANEL
ALUMINUM
EXTRUSION

Page 4 of 8
939500295 Rev E
4. Secure side panel to base
assembly using six (6) 1-1/4"
wood screws.
TIP: Insert screw through
extrusion to hold into place.
4
SIX (6) 1-1/4"
WOOD SCREWS

Page 5 of 8
939500295 Rev E
5. Stand base units
upright and gang base
units together (see
assembly instruction
939500801).
6. Place units against
wall and level.
7. Install upper
storage if applicable
(see assembly
instruction 939500809).
8. Add lower storage
(see assembly
instruction 939500811).
9. Install the aluminum
extrusion (9a) and
attach using screws at
top canopy joints and
ends of each unit (9b).
8"
5
9b
9a
9b
9b
6
ALUMINUM
EXTRUSION
#8 x 5/8" PAN
HEAD SCREW
NOTE: When drilling the rear
hole for a bolt, make sure the
hole is drilled 8" in from the
back of the unit.
Drill 3/16" holes in the aluminum
extrusion as required to ensure at least one
fastener is located at each canopy joint and
at each end of run.
NOTE:

Page 6 of 8
939500295 Rev E
10. Install three (3)
support blocks as
shown (10a) and
attach each
support block
using two (2)
screws (10b).
11. Install fascia
into the aluminum
extrusion at an
angle (11a) and
then place
downward (11b).
11a
10a
11b
10b
SIDE VIEW
TIP: Remove dust
cover supports by
simply breaking off.
SUPPORT BLOCK
SUPPORT BLOCK
FLUSH
#8 x 1-1/4"
WOOD SCREWS

Page 7 of 8
939500295 Rev E
Situation where a
Seam is Present
1. Flip fascia over and locate
pilot holes. Align strap with pilot
holes and scure using three (3)
#8-15 x 5/8" pan head screws.
2. Install fascia into the
aluminum extrusion at an
angle (2a) and then place
downward (2b).
3. Install second fascia into the
aluminum extrusion at an angle
(3a) and then place downward
(3b) and allow fascia to rest upon
strap.
2a
3a
3b
2b
1
STRAP
#8-15 x 5/8"
PAN HEAD SCREW

Page 8 of 8
939500295 Rev E
12.Remove
protective tape
backing from the
adhesive pad on
the back of the wall
trim (12a) and
install as shown
(12b). Trim if needed.
12a
12b
PROTECTIVE
TAPE BACKING
ADHESIVE PAD