Steelcase Eyesite User manual

If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2015 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
Page 1 of 4
23125201 Rev B
™
eyesite Monitor / Laptop Mounting
and Exchange
5/32" Allen Wrench
(provided)
#2 Phillips
Screwdriver
6b
1a
MONITOR MOUNT
RAIL ASSSEMBLY
VESA PLATE
7a
SCREW
MONITOR MOUNT
ASSEMBLY
2a
5a
ADJUSTMENT
SCREW
FOCAL
ADJUSTMENT
HANDLE
PIVOT OR
NON-PIVOT VERSION
7
6
2
1
Lift each vesa plate from each monitor mount rail assembly (1a).
Place vesa plate onto the back of monitor (2a) and secure using four
(4) screws. The holes to be used are determined by the monitor choice.
Use the outer four (4) holes for 100mm and the inner four (4) holes
for 75mm (2b).
The focal adjustment handle may need to be moved downward
depending on your monitor size. Locate the two (2) adjustment
screws located on the monitor tilt bracket and loosen (3a). Adjust
location of handle to be just below the bottom of the monitor (3b).
Repeat this procedure for other monitor tilt bracket.
3
75 mm
OR MOUNT
ASSSEMBLY
100 mm
7a
2b
®

Page 2 of 4
23125201 Rev B
®
4
5
Slide vesa plate back into the monitor rail bracket assembly (4a).
Take note of the embossed alignment arrow located on the vesa
plate. This should be pointed downward (4b).
To secure each monitor rail, you must install the set screw and
turn to the rght to tighten using a 1/16” Allen wrench (5a).
Close each vesa plate assembly cover (5b).
8a
MONITOR
MOUNT
BRACKET
ASSEMB
LY
SET SCREW
9a
EMBOSSED
ALIGNMENT ARROW
4a
MONITOR
MOUNT
BRACKET
ASSEMBLY
MONITOR MOUNT
ASSEMBLY
5a
VESA PLATE COVER
5b
4b

Page 3 of 4
23125201 Rev B
®
1
If Using a Laptop Mount
1d
RUBBER MAT
Optional Position #1
Optional Position #2
Optional Position #3
SIDE VIEW
LAPTOP MOUNT TRAY
RUBBER MAT
Be sure hooks and tabs
are fully engaged.
Use the correct optional position
(#1, #2 or #3) that best aligns the
laptop monitor to & from the user
to minimize eye strain.
Remove hardware bag from casting and install laptop mount
tray to casting with screws in hardware bag (1c). Place rubber
mat onto tray and position accordingly (1d).
1c
HARDWARE BAG WITH
SCREWS IS TAPED TO
THIS CASTING
INSTALL THIS
SCREW FIRST
LAPTOP MOUNT TRAY

Page 4 of 4
23125201 Rev B
®
1
Exchanging Mounting
Remove components as shown (1a). Remove existing monitor mount
rail assembly (1b). Slide tray assembly into rail (1c).
Re-install plate, screws and cap (1d). Insert the screws through the
oblong holes in the plate making sure the screws are against the
bottom of the oblong holes instead of the top.
This will ensure that the rectangular tabs on the inside of cap will fit
properly into the rail.
1a
1c
TRAY
ASSEMBLY
1b
MONITOR RAIL
ASSEMBLY PIVOT
OR NON-PIVOT
CAP
PLATE
1d
YES NO
End View
NOTE:
Push upward on plate so screws are
against bottom of oblong holes.
PLATE
PLATE