Steelcase FYI User manual

If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE(888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2019 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
®
Page 1 of 4
003876D Rev T
5/32"
HEX DRIVE
#2 Phillips
Screwdriver
Power Drill
11/32" Dia. Drill Bit
5/16 & 1/2 Wrench
FYI®Single & Dual Flat Panel Monitor Arm
Slatwall/SlatRail
Bracket
FPASWR
Wall Mount
Bracket
FPAWALL
Desk Clamp/
Grommet
Bracket
(Service Part)
Through Mount
Bracket
(Service Part)
FYI Single Monitor
Arm with Frame
One Bracket
FPASINGLEFO
1/16", 5/32", 3/16" & 1/4"
Allen Wrench
on architectural wall
and freestanding stanchions
NOTE: Located in Monitor
Arm Hardware Pack.
Slatwall/SlatRail
Wall Mount
1
1
2
4
32
Attach assembly to wall with (4)
fasteners (not included) appropriate
to the construction of the wall.
Use #10 wood
screws when
attaching to a
stud.
Use #10 toggle
bolts when
attaching directly
to drywall.
Desk Clamp / Grommet Through Mount
1 1
2
2
3
3
4
Drill
11/32"
hole
4
5
(Service Part) (Service Part)
Service Part Instruction
DFPASINGLECS
FYI Single Flat Panel Monitor
Arm with c:scape Bracket
DFPADUALCS
FYI Dual Flat Panel Monitor
Arm with c:scape Bracket
NOTE: DO NOT install C-Clamp mount in a scallop
cut-out on the worksurface. Failure to follow these
instructions could reduce the stability of the arm.
45 - 50 in-lbs
(5.1 - 5.7 Nm) 45 - 50 in-lbs
(5.1 - 5.7 Nm)
45 - 50 in-lbs
(5.1 - 5.7 Nm)
45 - 50 in-lbs
(5.1 - 5.7 Nm)

Page 2 of 4
003876D Rev T
®
DFPADUALCS
FYI Dual Flat Panel Monitor
Arm with c:scape Bracket
1b
2
CLAMPING
BRACKET
BRACE
BASE
BRACKET
1c
1a
FOR DUAL MONITOR ASSEMBLY ONLY - Guide
brace into place, beneath worksurface. Install two
(2) but do not tighten yet.
T-NUT
FLAT SIDE TO
FACE BRACKET
RAIL
SCREW
Side View
4
3
5
6
7
7
Attach FYI arm to receiver with screw/washers
(included with FYI arm).
Attach FYI arm/receiver assembly to base
bracket with included hardware (qty 2).
Tighten screws from step 1.
Max. Torque 40 in-lbs (4.5 Nm)
Tighten screws from step 2.
Install plastic cover by sliding it over the top
of the base bracket.
PLASTIC COVER
BASE BRACKET
3
WASHER
LOCK WASHER
RECEIVER
FYI ARM
CAP SCREW
4
FYI ARM/RECEIVER
ASSEMBLY
4
FYI ARM/RECEIVER
ASSEMBLY
DFPASINGLECS
FYI Single Flat Panel Monitor
Arm with c:scape Bracket
1
2
Mount screws and t-nuts in the correct orientation
as shown (1a). Slide clamping bracket into bottom
of base bracket (note tab direction per side view
(1b) and lower onto rail at rear of c:scape desk (1c).
Align two (2) t-nuts with rail slot to aid installation.
Do not tighten screws yet.
FOR SINGLE MONITOR ASSEMBLY ONLY -
Install two (2) screws but do not tighten yet.
Note:
Install (2) screws, but omit the
brace, when attaching to the
Campfire Big Table with center
rail and trough.
Single Dual
)
45 - 50 in-lbs
(5.1 - 5.7 Nm)

Page 3 of 4
003876D Rev T
®
Insert screws into bottom of monitor arm.
Allow two (2) fasteners to protrude approx.
1/4". These will be fully tightened after Step 2.
Slip bracket over screw heads (from Step 1)
using the keyhole slots. Slide brackets
together and tighten two (2) screws.
Guide two (2) flat head screws through bracket
and partially thread T-nuts onto screws. Note proper
orientation of T-nuts.
Place arm/bracket assembly onto desk rail. Tighten
two (2) flat head screws and T-nuts from Step 3.
Max. Torque 40 in-lbs (4.5 Nm).
Install locking plate onto face of assembled bracket.
Install and tighten final screw.
1
2
1
2
3
4
5
Install upper arm as shown.
6
Install VESA monitor plate as shown.
7
See note
below
Some modelswill
require this screw
to be installed by
theend user.
Frame One
Rail
Assembled and In position
on Frame One Rail
SIDE VIEW
5
3
3
4
6
7
FYI Single Monitor
Arm with Frame
One Bracket
FPASINGLEFO
NOTE: Located in Monitor
Arm Hardware Pack.
100 - 105 in-lbs
(11.3 - 11.9 Nm)
T-NUT
FLAT SIDE TO
FACE BRACKET

Page 4 of 4
003876D Rev T
®
FYI Single Monitor
Arm with Frame
One Bracket
FPASINGLEFO
SET SCREW
T-HANDLE
1
8
7
10
Attach VESA Bracket to backside of monitor.
Slide monitor mount assembly onto end of arm until audible
"click" is heard. Tighten set screw to prevent removal of
monitor.
Gently pry off cable cover on the bottom of the arm. Insert
cables into arm cavity and through two loops under
the arm. Press cover back into place.
Adjust T-handle to accommodate weight
of monitor. The monitor should "float"
(neither rise nor fall) when the
counterbalance is properly
adjusted.
DFPADUALCS
FYI Dual Flat Panel
Monitor Arm with
c:scape Bracket
Slatwall/SlatRail
Bracket
FPASWR
Wall Mount
Bracket
FPAWALL
Through Mount
Bracket
Desk Clamp /
Grommet
Bracket
(Service Part)
(Service Part)
7
8
10
insert cables
cable cover
9
9
DFPASINGLECS
FYI Single Flat Panel
Monitor Arm with
c:scape Bracket
RELEASE
MECHANISM
sinks when installed, pull up the
T-handle and turn clockwise until monitor
“floats”.
rises when installed, pull up the
T-handle and turn counter-clockwise until
monitor “floats”.
IMPORTANT:
Adjust the upper arm 20° above horizontal, to allow the
T-handle to turn easily. The T-handle will bind and could
break, if the upper arm is not in this position.
IMPORTANT - Adjustment Information