Steelcraft EX3 User manual

16
KEEP INSTRUCTIONS FOR FUTURE REFERENCE
EX3 Stroller
series AX656
Each Steelcraft unit is thoroughly inspected in our Quality Assurance
department prior to delivery. In the unlikely case that you find any
material or workmanship that affects the units normal operation,
we will repair the unit free of charge within 12 months of purchase. You
are required to present your receipt as proof of purchase.
For all concerns with your product please contact our Customer Service
team.
CUSTOMER SERVICE
1300 303 330 - Australia
0508 688 822 - New Zealand
Please read all the information carefully before using this product.
This warranty does not apply to failure due to improper care,
or normal wear and tear caused by product use. We reserve the
right to inspect the unit. You may be charged for repairs if the product
has been damaged accidentally.
Warranty
4000676
Distributed by:
AUSTRALIA
BRITAX CHILDCARE PTY.LTD.
A Britax International company.
(Incorporated in Victoria)
A.B.N. 55 006 773 600
99 Derby Road, Sunshine,
Victoria 3020, Australia
Phone: [phone]
Fax: [phone]
Due to our continuing program of development, Britax reserves the right to alter the specifications,
colour or design without any further notice.
The Steelcraft trademark is the property of Britax Childcare Pty. Ltd-Australia.
The Britax trademark is the property of Britax Excelsior Limited - UK.
Visit the Britax website at: http:/www.britax.com.au or email us at [email protected]
Due to the variations in the style and design of our products the illustrations used in this
instruction booklet are generic.
12/06 c 2006 Copyright Britax Childcare Pty. Ltd. Australia.
NEW ZEALAND
BRITAX CHILDCARE NZ. Limited.
A Britax International company.
101 Diana Drive, Glenfield,
Auckland 9, New Zealand.
Phone: [phone]
Fax: [phone]

02
READ THESE INSTRUCTIONS CAREFULLY AND KEEP THEM FOR FUTURE REFERENCE.
THE CORRECT USE AND MAINTENANCE OF THIS PRODUCT IS ESSENTIAL.
WARNINGS
.Do not leave occupant of stroller unattended.
.Follow the manufacturer’s instructions.
.Ensure your child is secured with a correctly adjusted safety harness.
.Do not carry additional children or bags on the stroller.
.Do not allow children to stand on the seat.
.Do not hang bags or goods from the handle as this could cause the stroller to tip over.
.Do not place more than 4kg in the basket, or 1kg in the canopy pocket (if supplied).
.The weight of the child using this product should not exceed 17kg.
.Do not use accessories other than those supplied and approved by Britax.
.When making adjustments to the stroller, ensure that you and your child’s body are
clear of any moving parts on the stroller.
.Always apply all of the brakes when parking the stroller.
.Check that all safety locks are engaged before placing a child in the stroller.
.Always raise the leg support (where fitted) to its highest position when transporting a
baby. This will reduce the risk of the baby falling out through the front of the stroller.
.Remove the child from the stroller before going up or down stairs and escalators.
.To prevent the risk of the stroller catching fire, do not park it near a radiator, an open
fire or a barbecue.
.Do not lift the stroller by the arm bar. It may disengage.
When using Bassinet:
.Use a harness as soon as the baby can sit up without help.
.This bassinet is designed for one child, never carry more than one child or additional
luggage in the bassinet.
.The weight of the child should not exceed 9kg.
When using the toddler seat:
.Only use this toddler seat with the EX3 three wheel stroller.
.Always assist your child in/out of the seat; a climbing child might tip the unit.
.Remember that excessive leaning on one side could cause stroller to be unstable.
.Not recommended for child under 6 months.
.Do not use this seat for a child that is unable to sit unassisted.
.The weight of the child should not exceed 17kg.
THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE
15
www.britax.com.au www.britax.com.au
NOTES

14 03
www.britax.com.au www.britax.com.au
B
ALay the chassis down flat and release the frame lock
catch.
BAdjust the handle to the user upright position by
simultaneously pressing the grey buttons on the
outside of the handle. Grasp the handle and lift
upwards allowing the chassis to extend and click
into position.
CCheck the stroller is ready for use by lifting the
handle - the stroller should not collapse.
DWhen using the bassinette, check if it is secure by
lifting the handles - the bassinette should not
disengage from the Stroller. The two hooks located
on the front underside of the bassinette must
engage with the stroller rear support bar.
WARNING: Do not lift stroller by bassinette.
NOTE: To assemble and install bassinette refer to
section 12 & 13.
NOTE: To install the toddler seat refer to section 15.
1. TO OPEN THE STROLLER
Some strollers have backrests adjustable between an upright and reclined position. The upright
positionsarenotsuitableforusewithchildrenlessthansixmonthsold.Asaguide,thelowestrecline
positionshouldbeusedtotransportbabies,thebackrestcanbe adjustedtoamoreuprightposition
as the child grows older and is able to support its head without assistance.
SAFETY WARNING
Thesunisverystrong.DONOTLEAVEYOURCHILDEXPOSEDTOTHESUN.Thecanopyorhoodon
this product will not give your child total protection from the harmful rays of the sun.
CARE AND MAINTENANCE
Regularly inspect and maintain your stroller to ensure the freedom of movement of the locking
devicesandsecurityofcomponents.To prolongthelifeofyournurseryproductkeepit cleananddo
not leave it in the direct sunlight for extended periods of time.
Removablefabriccoversandtrimsmaybecleanedusingwarmwaterwithahouseholdsoaporamild
detergent. Allow it to dry fully, preferably away from the direct sunlight.
HELPFUL HINTS
If the wheels squeak - use a silicon based spray or light oil ensuring it penetrates the wheel and axle
assembly.
When using your stroller at the beach - completely clean your stroller afterwards to remove the sand
and salt from the mechanisms and wheel assemblies.
If there are compression marks on the tyres - use a domestic hair dryer to gently warm the tyre and
the compression marks should slowly disappear. (DO NOT OVERHEAT).
DO NOT DRY CLEAN, OR USE BLEACH.
Do not machine wash, tumble or spin dry, unless the care labelling on the product permits these
methods.
Non removable fabric covers and trims may be cleaned using a damp sponge with soap or mild
detergent. Allow it to dry completely before folding or storing it away.
In some climates the covers and trims may be affected by mould and mildew. To help prevent this
occurring, do not fold or store the product if it is damp or wet. Always store the product in a well
ventilated area.
Alwayscheckpartsregularlyfortightnessofscrews,nutsandotherfasteners-tightenifrequired.To
maintainthesafetyofyournurseryproduct,seekpromptrepairsforbent,torn,wornorbrokenparts.
Use only those parts and accessories approved by Britax.
RECOMMENDATION

04 13
A Remove the plastic protector (where fitted) from the
front forks.
BPush the front wheel axle fully into the wheel forks.
CPlace the securing washer on both sides, ensure
the tabs in the washers are located into the circular
holes just above.
DTighten the front wheel axle by turning the quick
release hub in a clockwise rotation and fold lever to
lock.
NOTE: Solid (EVA) tyres do not require inflation.
Pneumatic Front and Rear Tyres can be inflated
with pump (where supplied) or a bicycle pump or
at a garage air pump. Refer to the tyre side wall for
maximum inflation pressure.
2. TO INSTALL THE FRONT SWIVEL WHEEL
D
D
www.britax.com.au www.britax.com.au
16. TO REMOVE THE TODDLER SEAT
A
B
C
D
B
A
A
B
WARNING: Always remove your child from the stroller/
toddler seat prior to installation or removal.
ATo remove toddler seat, pull and hold the locking
knob on the upper mounting bracket 1, then push
the bracket fully forward and outwards 2. Repeat
this process for both upper mounting brackets.
BRotate the toddler seat forward until the indicators
on the lower mounting brackets align with the
indicators on the stroller frame, then pull the
toddler seat out of the stroller frame in an upwards
direction.
17. TO FOLD THE STROLLER WITH TODDLER SEAT
ARelease the upper mounting brackets as
described in section 16(A), then rotate the
toddler seat fully forward and rotate the
upper mounting brackets into the rear of
the toddler seat 1. Standing behind the
stroller pull both locks 2. Push the handle
forward 3 allowing the stroller to fold until
the chassis moves into a fully folded
position.
BApply the frame lock catch.

05
12
3. TO INSTALL THE REAR WHEELS
A
www.britax.com.au www.britax.com.au
AStore the bassinette handles inside the zipped
pockets and fold the bassinette canopy back
towards the rear of the bassinette. (For a more
compact fold it is optional to release the bassinette
frame rods towards the middle of the bassinette
and push lightly down until the bassinette
collapses). Standing behind the stroller pull both
locks (refer to section 10 A). Push the handle
forward allowing the stroller and bassinette to fold
until the chassis moves into a fully folded position.
BApply the frame lock catch.
15. TO INSTALL THE TODDLER SEAT (where supplied)
WARNING: Always remove your child from the stroller/
toddler seat prior to installation or removal.
ARemove the arm bar (if fitted) as described in
section 9.
BThe toddler seat has locating slots on the lower
mounting brackets. Rotate these slots until they
align with the opening in the moulding.
CAlign the slots on the lower mounting brackets with
the tongues on the inside of the stroller frame, then
push the lower mounting brackets into the tongues.
DRotate the upper mounting brackets outwards,
then raise the toddler seat to an upright position.
Push the circular hole in the upper mounting
bracket fully over the stud on the stroller frame 1
then pull the upper mounting bracket forward until
it locks into position 2 . Repeat this process for
both upper mounting brackets.
ECheck the toddler seat is securely in place by
pulling on it.
FRefer to section 8 to secure child in the harness.
CAUTION: Do not lift the stroller by the toddler seat. It
may disengage.
14. TO FOLD THE STROLLER WITH BASSINETTE
A
B
C
D
E
A
A
B
C
A
A Push each rear wheel into the chassis until they
lock into position.
BCheck the wheels are correctly fitted by trying to
pull them out.
NOTE: The rear wheels can be removed for more
compact storage. Do this by lifting the lock lever
(shown by arrow ) on the top of the rear wheel
housing, then pull the wheel out.
4. TO USE THE STROLLER CANOPY
WARNING: Do not use the stroller canopy when
bassinette is in use.
ATo fit the canopy push the clips onto the handle
frame (shown by arrows) on both sides of the
stroller and attach the press fit studs onto the clips.
BOpen the canopy by pulling the front of the canopy
forward and push the canopy hinges down on each
side to lock it in open position.
CTo open the canopy window (where fitted) pull the
flap away from the canopy and roll it up. Hold it in
place by attaching the fastener.
DTo remove the canopy remove clips from the frame
on both sides.
A

06 11
5. TO RELEASE/LOCK THE SWIVEL WHEEL
A To release the front swivel wheel allowing greater
mobility, rotate the knob clockwise until the rivet in
the knob faces forward.
BTo lock the swivel wheel, rotate the knob clockwise
half a turn and move the fork until it locks into
position.
6. TO LOCK/RELEASE THE PARK BRAKE
ATo use the foot (park) brake, push lever down to
lock the wheels.
BLift brake lever up to release the wheels.
NOTE: Always apply the foot brake whenever you park
the stroller.
7. TO ADJUST THE BACKREST
ATo fully recline the backrest release the press studs
and open outer and then inner zips located on the
sides of the infant seat.
BTo raise the backrest close the inner or outer zips
to the desired position, then attach the press
studs.
www.britax.com.au www.britax.com.au
13. TO INSERT THE BASSINETTE
Use only EX3 bassinet.
WARNING: When bassinette is in use, arm bar, stroller
canopy and seat insert must be removed.
ARemove the arm bar as described on page 8.
BRemove the stroller canopy as described on
page 5.
CTo remove the seat insert release all press studs
and hook and loop tabs from the stroller frame
(refer to page 9 for exact locations), including
the strap under the foot rest. Lift the seat insert
out of the stroller.
DPlace the bassinette onto the stroller frame by
engaging the two front hooks on the underside of
the bassinette with the stroller front support bar.
EOpen the two rear locking clips located under the
front end of the bassinette and push down
bassinette onto the rear stroller support bar and
lock the clips.
FCheck the bassinette is secure by lifting the
handles - the bassinette should not
disengage from the stroller.
Rear locking clip
Front
support
bar
(where supplied or purchased)
Rivet
A
B
Rear
support
bar

07
10
8. TO SECURE YOUR CHILD IN THE HARNESS
WARNING: Use this harness at all times.
A five-point harness is provided to restrain your child. To
secure the child in the harness, push buckle (A) and (B)
into the buckle housing (C) until the buckle prongs snap
into position. Carefully adjust the harness by pulling the
slider (D) until the desired snug fit is achieved in the lap,
shoulderandcrotchstraps.Alwaysadjusttheharnesswhen
changing the seating position of the child. To release the
buckle, squeeze the top and bottom prongs.
AExtend the bassinette frame rods outwards until
they lock into position. Push down lightly on the
top edges of the bassinette to check that it does
not collapse.
BFit the inner liner to the bassinette and attach the
press studs to the canopy moulding. Place the
mattress inside the bassinette.
CTo fit the canopy push the tongues into the
moulded slots on top of the bassinette, then fit the
double sided press studs to the canopy moulding.
DFit the cover and attach the press studs to the
double sided press studs on the canopy.
ERemove the handles located inside the zipped
pockets on either side of the bassinette.
NOTE: D-rings are installed in the base of the
bassinette for optional baby harness installation.
Baby harness is not supplied but can be purchased
separately. Refer to instruction included with baby
harness for correct fitting.
12. TO ASSEMBLE THE BASSINETTE (where supplied or purchased)
A
D
C
www.britax.com.au www.britax.com.au

09
08
9. TO USE THE ARM BAR (where supplied)
A The arm bar has locating slots on both ends.
Rotate these slots until they are clear of the plastic
moulding.
BAlign the slots in the arm bar with the tongues on
the inside of the stroller frame and push the arm
bar into the tongues.
CPress both buttons on the insides of the arm bar
then rotate the arm bar upwards until it locks into
position. Check the arm bar is securely in place by
gently pulling on it.
IMPORTANT: Arm bar must be fully raised when child
is in stroller.
DTo remove arm bar press both buttons on the
insides of the arm bar, then rotate bar down
towards footrest and pull to remove.
CAUTION: Do not lift the stroller by the arm bar.
It may disengage or break.
NOTE: The arm bar must be removed to use the
bassinette or toddler seat.
10. TO FOLD THE STROLLER
WARNING: Arm bar (if fitted) must be folded to the
lowest installation position before folding the stroller.
ATO FOLD THE STROLLER WITHOUT BASSINETTE
OR TODDLER SEAT fold the canopy back and arm
bar down (where fitted), then stand behind the
stroller and pull both locks. Push the handle
forward allowing the stroller to fold until the chassis
moves into a fully folded position.
BApply the frame lock catch.
SEAT INSERT FIXING POINTS
SEAT INSERT FITMENT CHECK
A
B
C
A
A
11. TO ASSEMBLE THE SEAT INSERT
WARNING: The seat insert must be assembled as
below to ensure correct operation of the stroller.
A Attach the two press studs A located at the top of
the insert to the press studs on the rear of the
handle frame and attach hook and loop tabs B
around the handle frame.
BAttach the press stud C on the strap to the press
stud located on the inside of the rear of the leg
ensuring the strap is looped around the outside leg
before attaching the press stud.
CAttach the bottom press studs on the insert D to
the press studs on the rear of the bend in the
bottom frame and attach hook and loop tabs
E below, around the bottom frame.
NOTE: Repeat the above steps for both sides of the
stroller.
DPass the long strap F through the D-ring on the
short strap G on the other side and attach the
hook and loop.
NOTE: Refer below for seat insert fitment check.
E Check the seat insert is fitted and attached to both
sides of the stroller frame as per the pictures below.
www.britax.com.au www.britax.com.au