STEINEL ISD 3360 User manual

IS 3180
IS 3360
IS 345
8135904 Technische Änderungen vorbehalten.
i
DGBFNL
IE
PSDKFINNGRTRHCZSKPLRO
SLO
HR
EST
LTLV
RUS
BDAL_IS3180_24spr_neu 25.07.2008 15:09 Uhr Seite 2

max. 20 m
180°
20 m
4 m
12 m
20 m
0
I
360°
20 m
3 m
10 m 10 m
4 m
2,5 m
20 m 20 m
max. 20 m
2 m
IS 3360
IS 345
IS 3180
2
BDAL_IS3180_24spr_neu 25.07.2008 15:09 Uhr Seite 3

3
BDAL_IS3180_24spr_neu 25.07.2008 15:09 Uhr Seite 4

4
3
13
9
8
7
5 sec.-15 min Reset 5 sec.2 - 2000 Lux
1210 11
15
15
BDAL_IS3180_24spr_neu 25.07.2008 15:09 Uhr Seite 5

5
BDAL_IS3180_24spr_neu 25.07.2008 15:09 Uhr Seite 6

6
10 m 10 m
3 m4 m
20 m 20 m
2,5 m
IS 3360
IS 345
BDAL_IS3180_24spr_neu 25.07.2008 15:09 Uhr Seite 7

7
BDAL_IS3180_24spr_neu 25.07.2008 15:09 Uhr Seite 8

The unit is equipped with pyro sensors that
detect the invisible heat emitted from moving
objects (people, animals etc.). The heat detect-
ed in this way is electronically converted into
a signal that switches on connected loads
(e.g. a light). The built-in red LED also lights up.
The sensor does not detect heat radiated from
behind obstacles, such as walls or panes of
glass. Heat radiation of this type will therefore
not activate a light.
Principle
14
Installation instructions
Dear Customer,
GB
Safety warnings
■Disconnect the power supply before at-
tempting any work on the sensor!
■The electrical connection lead must be
dead during installation. Therefore, switch
off the power first and use a voltage tester
to make sure the wiring is off circuit.
■Installing the sensor involves work on the
mains power supply. This work must there-
fore be carried out professionally in accord-
ance with applicable national wiring regula-
tions and electrical operating conditions.
(D-VDE 0100, A-ÖVE-EN 1, -SEV 1000)
■Only select time and twilight setting with the
lens in place.
Congratulations on purchasing your new
STEINEL infrared sensor and thank you for the
confidence you have shown in us. You have
chosen a high-quality product that has been
manufactured, tested and packed with the
greatest care.
Please familiarise yourself with these instruc-
tions before attempting to install the sensor
because prolonged reliable and trouble-free
operation will only be ensured if it is fitted
properly.
We hope your new infrared sensor brings you
lasting pleasure.
The site of installation should be at least 50 cm
away from another light because heat radiated
from it may activate the system.
An optional corner wall mount (product no.
648015 black or 648114 white) is available for
installing the sensor on internal and external
corners.
The mains lead consists of a 3 phase cable.
L = Phase
N= Neutral conductor
PE = Protective-earth conductor
If the rubber seal is damaged, the cable entry
openings must be sealed with an M 16 or M 20
(at least IP 54) double seal cable gland.
A condensation hole is indicated next to the
rubber seal. This must be opened if necessary.
Installation
BDAL_IS3180_24spr_neu 25.07.2008 15:09 Uhr Seite 15

15
Lamp not fitted with a neutral conductor
Lamp fitted with a neutral conductor
Connection via two-circuit switch for
manual and automatic operation
Connection via a two-way switch for
manual override and automatic operation
Position I: automatic operation
Position II: manual operation
light ON permanently
Note: the system cannot be switched off,
but operated only at settings I and II.
a) Load, max. illumination 2000 W
(see Technical specifications)
b) Sensor connection terminals
c) Indoor switch
d) Indoor two-circuit switch, manual,
automatic
e) Indoor two-way switch, automatic,
manual override
Several sensors connected in parallel
(not illustrated)
In this case, it is important not to exceed
a sensor's maximum connected rating.
In addition, all units must be connected to
the same phase.
Connection examples
System components
IS 3180, IS 3360, IS 345
Standard installation
Installation in ceiling box
Basic element
Concealed wiring
Surface wiring
Plug-in terminals
Fitting the sensor cover
Fitting the shrouds
Screwing on the lens
Twilight setting (2 – 2000 lux)
Time setting (5 sec. – 15 min.)
Reset button for returning the twilight and
time setting to the factory setting of 2000
lux and 5 sec.
Fitting the decorative faceplate
Lens rotates for selecting basic settings:
8 m max. or 20 m max.
Lens slides for adjusting reach:
4 – 8 m or 8 – 20 m
IS 3180
Drainage hole for wall installation
(open if necessary)
Drainage hole for ceiling installation
(open with a 5 mm drill if necessary)
Mounting
height Setting level radially Setting level tangentially radiallytangentially
1.5 m
2.0 m
2.5 m
3.0 m
8
–
–
–
20
8
–
–
–
20
8
–
–
–
20
8
–
–
–
20
5 m
6 m
7 m
8 m
12 m
5 m
6 m
7 m
10 m
20 m
6 m
8 m
10 m
13 m
20 m
8 m
9 m
12 m
17 m
20 m
2.5 m
2.5 m
3.0 m
3.0 m
4.5 m
2.5 m
3.0 m
3.5 m
4.0 m
4.5 m
3.0 m
4.0 m
5.0 m
5.0 m
4.0 m
4.0 m
4.5 m
5.0 m
4.0 m
4.0 m
4
–
–
–
8
4
–
–
–
8
4
–
–
–
8
4
–
–
–
8
3 m
5 m
6 m
7 m
9 m
4 m
5 m
6 m
8 m
8 m
5 m
7 m
8 m
9 m
10 m
5 m
6 m
8 m
10 m
13 m
2.0 m
2.5 m
3.0 m
3.0 m
3.5 m
3.0 m
3.0 m
3.0 m
3.0 m
3.5 m
3.0 m
3.5 m
3.5 m
4.0 m
3.5 m
3.0 m
3.0 m
4.0 m
4.5 m
5.5 m
Reaches for IS 3180
20 m lens 8 m lens
GB
21
BDAL_IS3180_24spr_neu 25.07.2008 15:09 Uhr Seite 16

16
The system can be put into operation once the
mains power has been connected and the unit
is closed. Two setting options are concealed
behind the decorative faceplate.
Pressing a programming button sets the
sensor to programming mode.
This means:
- The lamp connected always goes out
- Sensor function is deactivated
- Manual override function (if active) is can-
celled
The settings may be altered as often as you
wish. The last setting will remain stored in the
memory in the event of power failure.
Important: Only select time and twilight
setting with the lens in place.
Functions
a) Selecting twilight setting of your choice:
At the light level at which you now want the
sensor to respond to movement and switch on
light, press the button until the red LED
flashes (in the lens). This light level will now be
stored.
Important: When setting, do not cover the lens
or shade it with your own shadow.
b) Setting night-time operation (4 lux) during
the day
Keep the button pressed for approx. 5 sec-
onds until the red LED stops flashing in the lens.
(factory setting:
daylight operation
2000 lux)
Twilight setting (response threshold) 
2 – 2000 lux
The ON time can be varied continuously
between approx. 5 sec. and a maximum of
15 min.
(factory setting:
approx. 5 sec.)
Time setting (switch OFF delay) 
5 sec. - 15 min.
- To select the shortest time setting, press
button twice in brief succession.
b) Setting ON time to the accuracy of one
minute
- Keep button pressed until red LED
flashes (in the lens).
- Release button , now keep button
pressed until LED goes out and (after 3 sec.)
starts to flash again (slower).
- After the chosen number of flashes (each
LED flash equals 1 minute of light ON time),
re-press button until LED goes out.
Your chosen time is now stored to the
accuracy of a minute.
- This process is terminated automatically
after the maximum number of flashes
(15 times = 15 min.).
c) Pulse function
The pulse function activates the output for
2 sec. (e.g. for staircase lighting time switches).
To do this, keep button pressed
for approx. 5 sec. until the red LED stops
flashing.
a) Setting ON time to the accuracy of one
second
- Keep button pressed until red LED flashes
(in the lens).
- Release button and wait until chosen ON
time is shown (LED flashes).
- Press button again until LED goes out.
Your chosen time is now stored to the
accuracy of a second.
- This process is terminated automatically
after the maximum selectable time (15 min.).
All settings can be returned to their original
levels (daylight operation 2000 lux, ON dur-
ation 5 seconds) whenever you wish.
To do this, keep both buttons pressed simul-
taneously until the LED (in the lens) comes on
and goes out again (approx. 5 seconds).
Reset function
The sensor's response threshold can be set
to between approx. 2 lux and 2000 lux.
BDAL_IS3180_24spr_neu 25.07.2008 15:09 Uhr Seite 17

17
Sensor operation
1) Switch light ON (when light is OFF):
Turn switch OFF and ON once.
Light stays on for the period selected.
2) Switch light OFF (when light is ON):
Turn switch OFF and ON once.
The light goes out or switches over to sensor
mode.
Manual override function
2 x aus/an
4 Stunden
5 sec. – 15 min.
1 x OFF/ON
IS 3180 IS 3360 IS 345
Dimensions: (l x w x h) 95 x 95 x 65 mm
Output: • 2000 W max., VDE tested
(resistive load, e.g. filament bulb)
• 10 AX max., VDE tested (fluorescent tube)
• 900 W max. (series corrected)
• 500 W max. (parallel corrected,
at C = 45.6 µF
• 600 W max. (electronic ballasts, capacitive,
e.g. low-energy lamps, 8 each max.)
Mains power: 230 – 240 V, 50 Hz
Recom. mounting height: 2 m 2.5 m 3 m
Angle of coverage: 180° horizontally 360° horizontally 12 x 4 m radially
90° vertically 180° vertically 20 x 4 m tangentially
Reaches: – 20 m max. all-round 20 x 4 m max.
Basic setting 1: 4 – 8 m max. – –
Basic setting 2: 8 – 20 m max. – –
Detection levels: 7 10 5
Switching zones: 448 1416 280
Twilight setting: 2 – 2000 lux 2 – 2000 lux 2 – 2000 lux
Time setting: 5 sec. – 15 min. 5 sec. – 15 min. 5 sec. – 15 min.
Manual override: selectable (4 h) selectable (4 h) selectable (4 h)
Enclosure: IP 54 IP 54 IP 54
Technical specifications
Manual override
1) Select manual override :
Turn switch OFF and ON twice. The lamp is
set to stay on for 4 hours (red LED lights up
behind the lens). Then it returns automatically
to sensor mode (red LED off).
2) Deactivate manual override:
Turn switch OFF and ON once. The light goes
out or switches over to sensor mode.
2 x aus/an
4 Stunden
4 hours
2 x OFF/ON
If a mains switch is installed in the mains supply
lead, the light is capable of the following func-
tions in addition to the simple ON/OFF function:
Important: The switch should be actuated in
rapid succession (in the 0.5 – 1 sec. range).
GB
BDAL_IS3180_24spr_neu 25.07.2008 15:09 Uhr Seite 18

18
Troubleshooting
Malfunction Cause Remedy
Sensor without power ■Fuse faulty, not switched
ON, break in wiring
■ Short circuit
■New fuse, turn on power
switch, check wiring with
voltage tester
■Check connections
Sensor will not switch ON ■Twilight control set to night-
time mode during daytime
operation
■Bulb faulty
■Power switch OFF
■Fuse faulty
■Detection zone not properly
targeted
■LED flashes approx. once
a second, sensor in time
setting mode
■Reset
■Change bulb
■Switch ON
■New fuse, check connection
if necessary
■Re-adjust
■Press button once
Sensor will not switch OFF ■Continuous movement in the
detection zone
■Light being operated in the
detection zone causing sen-
sor to responds as a result
of change in temperature
■Light being operated is in
the manual override mode
(LED ON)
■Check zone, adjusting if
necessary, or shroud
■Change zone, or shroud
■Deactivate manual override
Sensor keeps switching
ON/OFF
■Lamp being operated in
the detection zone
■Animals moving in the
detection zone
■Change zone, shroud or
increase distance
■Change zone, or shroud
Sensor responds when it
should not
■Wind is moving trees and
bushes in the detection zone
■Cars in the street are being
detected
■Sunlight is falling onto the
lens
■Sudden temperature changes
due to weather (wind, rain,
snow) or air expelled from
fans, open windows
■Change detection zone
■Change detection zone
■Mount sensor in a sheltered
place or change detection
zone
■Change detection zone,
change site of installation
Change in sensor's reach ■Differing ambient tempera-
tures
■Use shrouds to define detec-
tion zone precisely
LED flashing rapidly
(approx. 5 x per second)
■Load connected is too high ■Reduce load or use
contactor
BDAL_IS3180_24spr_neu 25.07.2008 15:09 Uhr Seite 19

The infrared sensor is suitable for switching on
light automatically. The unit is not suitable for
burglar alarm systems as it is not tamperproof
in the manner prescribed for such systems.
Weather conditions may affect the way the
motion detector works. Strong gusts of wind,
snow, rain or hail may cause the light to come
on when it is not wanted because the sensor is
unable to distinguish sudden changes of tem-
perature from sources of heat. The detector
lens may be cleaned with a damp cloth if it
gets dirty (do not use cleaning agents).
Operation/Maintenance
This STEINEL product has been manufactured
with the utmost care, tested for proper operat-
ion and safety in accordance with applicable
regulations and then subjected to random
sample inspection. STEINEL guarantees that it
is perfect condition and proper working order.
The warranty period is 36 months, starting on
the date of sale to the consumer. We will rem-
edy defects caused by material flaws or manu-
facturing faults. The warranty will be met by re-
pair or replacement of defective parts at our
own discretion.
This warranty shall not cover damage to wear-
ing parts, damage or defects caused by im-
proper treatment or maintenance.
Further consequential damage to other objects
is excluded.
The warranty will only be honoured if the prod-
uct is sent to the appropriate Service Centre
fully assembled and well packed with a brief
description of the fault, receipt or invoice (date
of purchase and dealer's stamp).
Repair Service:
Our Customer Service Department will repair
faults not covered by warranty or occurring
after the warranty period has
expired. Please send the product
well packed to your nearest
Service Centre.
Functional warranty
This product complies with the European Dir-
ective on Low-Voltage Appliances, 73/23/EEC
and the EMC Directive 89/336/EEC.
Declaration of conformity
19
GB
BDAL_IS3180_24spr_neu 25.07.2008 15:09 Uhr Seite 20