stellar labs HORIZON HR20A User manual

©StellarTechnologiessp.zo.o2020
F o l l o w i n g i n f o r m a t i o n i s o n l y f o r E U - m e m b e r s t a t e s :
The use of this symbol indicates that this product may not be treated as
household waste. By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of
this product, please contact your local council, your household waste
disposal service or the shop where you purchased the product.
Stellar Technologies sp.zo.o
Address: ul. Krucza 68/9, 53-411 Wroclaw, Poland
Tel: +48 736 360 603
info@stellarheaters.com
www.stellarheaters.com
KRS: 0000720919
NIP: 8971852649
Models: HR20A; HR20W; HR20S;
HORIZON
REFERENCE MANUAL
CAUTION
Read all these operating and assembly instructions carefully before using the appliance. Stellar Technologies cannot assume any
responsibility for personal injury or damage of property resulting from failure to abide by the instructions provided in this reference
manual. Owner and the operator are responsible to read and comply with the following instructions:
· Children of less than 3 years should be kept away unless continually supervised.
· Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its
intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or
perform user maintenance.
· CAUTION - Some parts of the product can become very hot and cause burns. Particular attention has been given where children
and vulnerable people are present. After unpacking the product, check that everything is present, if in doubt contact Stellar Technologies
or authorized distributor in your area.
·Do not leave packaging in the reach of children or vulnerable people.
Before using the heater
- Check the voltage indicated on the type plate corresponds to the mains supply voltage.
- Ensure that the heater has been securely fastened in its final mounting position.
· Do not locate the heater immediately below a socket outlet.
·D o not sit or rest objects on the appliance
· Do not use the heater in areas where inflammable substances or vapors are present.
· Do not touch the heater with wet and damp hands or with wet feet.
· Remove the plug from the mains socket (or disconnect pole switch) during installation, cleaning and/or replacing the lamp and
ensure that the lamp and body is cool.
· Do not modify the appliance in any way.
· Do not use an extension cord with this product because the extension cord may overheat and cause a risk of fire.
· Keep the mains supply cord away from the body of the heater which will get hot during use.
· Arrange the mains supply cord so it cannot be tripped over or damaged.
· Do not cover or obstruct the heater while it is in use.
· Do not insert any object through any slot or opening in the heater.
· Do not install less than the minimum mounting distance from the floor.
All dimensions shown in mm (+/-2 mm)

Installation and Mounting
Horizon heater is fitted with a supply cable, therefore opening of the wire connector is not required in order to carry out normal installation of
this product. The heater intentionally does not come with the moulded plug, but the special heat proof cable, therefore connection and wiring
should be done by qualified professionals only.
• Please observe the minimum safe distance between the heater body and any inflammable surfaces.
• If the supply cord becomes damaged, it must be replaced by the manufacturer, its service agent or a similar qualified person in order to avoid
a hazard. When electrical connection is outside, it is recommended that a waterproof socket or a junction box is used for the connection.
If in any doubt, please contact a suitably qualified electrician. The Horizon heater lamp has universal burning position. It can be wall mounted
horizontally in an angled manner. Wall mounting bracket is included in the box. Horizon heater can also be hung from a ceiling with a suitable
ceiling mounting bracket or chains. (ceiling brackets and chains not included in the box.) When mounting on a wall or a similar surface
horizontally, do not position heater at an angle less than 45° and more than 90°.
IMPORTANT Before drilling the holes in the wall or other surfaces, ensure that there are no wires or pipes in the area of the holes. Contact
qualified person with the equipment and knowledge to identify non observable wires or pipes placed under the surface.
1. The heater body and lamp should be cool and the power supply disconnected. Heater Power cable should be in your area of visibility,
while being disconnected to exclude the chance that someone one your premises might reconnect or switch on power supply while you
are performing lamp replacement or other maintenance procedures.
2. Remove the screws from left and right side reflectors, and lift off the reflectors one by one, see - Fig. A.
3. Once side reflectors have been removed - see Fig. B Locate the waterproof cable connector, see - Fig C . Identify the side where lamp
cables are entering the connector. First turn and loosen the outer cap, then turn and loosen the inner cap, see - Fig. D
4. Once you have located a junction inside the waterproof connector, unscrew the lamp cables. 2 white cables, see - Fig. E
5. Remove lamp cables from connector gland so they are loose and locate the lamp cable on the opposite side, see - Fig. F
6. Pull out the cable of the lamp by slightly bending the central reflector, see - Fig. G
7. Once both cables of the lamp are loose, gently remove the lamp by holding the ceramic caps on both ends simultaneously, pull out the
lamp from the lamp holder, see - Fig. H
8. The emitter should now be fully removed along with its cables, see - Fig. I
9. Refit the new infrared lamp in reverse order and ensure that all screws, glands are fully tightened and no wires are trapped or left
disconnected.
Fig. E
Fig. A
Fig. D
Fig. G
Fig. B
Fig. H
Fig. C
Fig. F
Fig. I
Maintenance
• Disconnect from the mains supply before attempting any maintenance procedure or cleaning.
• To maintain maximum heat effectiveness, the reflector can be wiped with a soft cloth before reassembling in case if it shows considerable
signs of dust and dirt.
Replacement Infrared Lamp
The replacement lamp should be exactly the same as the one it was supplied with. Failure to fit the exact same type could cause the heater
to fail or even become dangerous especially when used in an outdoor environment. Please contact Stellar Technologies for purchasing a
replacement lamp and provide model number.
New infrared lamp should not be touched with bare hands. Finger marks will burn into the quartz glass causing premature failure. Remove
finger marks with a soft cloth dampened in alcohol.
Lamp Replacement Procedure
Power supply should be disconnected before an attempt to replace the lamp.
Lamp replacement should be conducted by a qualified personnel. This procedure should be conducted with compliance of electrical
regulations
When mounting Horizon heater in an angled manner do not position the heater at an angle more than 45° and less than 30° to the
horizontal line. Make sure the beam or structure can withstand the heater weight in different climatic conditions, like wind. When wall
mounting secure the U shaped wall bracket first on the wall, with both holes in the bracket. Wall fixings, (screws, bolts etc.) are not
supplied with the heater and it should be selected according to the material the mounting is performed on therefore mounting should be
conducted by a qualified person.
Technical Data
Risk of Fire
Keep combustible materials such as furniture, papers, clothes and curtains at least 1.8m (6 feet) from the front of the heater and away from
the sides and rear. If the heater is to be used outside, we recommend that a waterproof socket is used.
Introduction
The Horizon heater is created to give you maximum heat output instantly. Which can be directed to the area where the heat is required. It is
designed to be the most powerful heater on the market in the world, suitable for indoor and outdoor use and therefore it is weatherproof.
Horizon heater is made of high quality materials only and will give you years of service if installed and maintained properly.
· Do not pull or carry the appliance by the power cable.
· Do not use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired or replaced by a qualified electrician.
If the product falls or receives a hard shock get it checked by an authorized technical assistance center.
· . The lamp can be damaged when contacted with bare hands.Do not touch the heater lamp, even when cold
· Should you accidently touch the surface of the lamp, gently clean it with soft cloth, dampened with alcohol.
· During maintenance do not touch the lamp directly, but handle only by the end of ceramic caps on both sides simultaneously.
· Do not touch or hold the heater at reflector area.
· Do not use the appliance in conjunction with programmers, timers or other devices capable of switching it on automatically.
· Heaters must be switched on and off one by one to avoid voltage surges which can cause failure of the lamp.
· Do not replace the power (mains) cable of the heater. This heaters is equipped with a special cable which can withstand high temperatures.
Replacing power (mains) cable with another cable, (even if it visually looks the same) can cause electric shock, injury or death.
IMPORTANT:
Save this instructions for future reference
HR20S
HR20W
HR20A
WARNING: This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms
when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
· Do not touch the heater when it is turned on, as the body gets hot.
· Do not touch, cover or store the heater immediately after turning off, wait until the body of a heater cools downs
· Do not use the heater in a bathroom, laundry areas and similar locations. Never locate the heater where it may fall into a bathtub or
other water container.
· Do not use in explosive atmospheres.
· A heater has hot parts inside. Do not use it in areas where petrol, paint, or flammable liquids are used or stored.
WARNING: This appliance must be connected to a supply that is earthed!
This manual suits for next models
2
Popular Heater manuals by other brands

DeLonghi
DeLonghi TCH8093ERBCA Instructions for use

Dimplex
Dimplex DEC Series installation instructions

UFESA
UFESA Calefactor CF2000 instruction manual

ToggenGear
ToggenGear ALPINE 2020 IH user manual

Herschel
Herschel IP44 Installation & operating instructions

Timberk
Timberk Power Door Series instruction manual