Sterling Bath Whirlpool 76111110 User manual

Features
•Compression molded from our exclusive solid Vikrell
®
material
•Integral apron with removable access panel
•Durable high-gloss finish
•Pump with air switch and grounding-type plug-in cord
•6 Jets
•Optional three-piece wall set with generous storage
shelves
•10-year consumer/3-year commercial limited warranty
•16″(406 mm) whirlpool bath depth (floor to top of
threshold)
•60-1/4″(1530 mm) x 43-1/2″(1105 mm) x 20″
(508 mm) complete unit rough-in dimensions include
flange
•60″(1524 mm) x 42″(1067 mm) x 19″(483 mm)
complete unit finished dimensions include wainscot
Codes/Standards Applicable
Specified model meets or exceeds the following:
•ASME A112.19.7
•ANSI Z124.1.2
•ASTM E162
•ASTM E662
•UL 1795
•HUD, UM Bulletin 73A
42″(1067 mm) WHIRLPOOL BATH
76111110
ALSO 76111120
Colors/Finishes
•0: White
•Other: Refer to Price Book for additional colors/finishes
Specified Model
Model Description Colors/Finishes
76111110 42″(1067 mm) whirlpool bath, left drain (shown) ❑0❑Other_____
76111120 42″(1067 mm) whirlpool bath, right drain ❑0❑Other_____
ENSEMBLETM
Page 1 of 2
1021378-4-H
For more information
visit SterlingPlumbing.com
or call 1-800-STERLING

Technical Information
Fixture*:
Basin area:
Bathing well 40″(1016 mm) x 27″(686 mm)
Top area 52″(1321 mm) x 35″(889 mm)
To overflow:
Water depth 11″(279 mm)
Capacity 55 gal (208.2 L)
* Approximate measurements for comparison only.
Pump: V Hz A
1-speed 120 60 7
Model Door width Door maximum
height
76111110
76111120
58-1/2″(1486 mm) *NA
* Varies with alternative walls.
Required Electrical Service
Dedicated circuit required, protected with Class A
Ground-Fault Circuit-Interrupter (GFCI):
Pump 120 V, 15 A, 60 Hz
Installation Notes
Install this product according to the installation guide.
Pump is supplied with a grounding type plug-in cord. Locate
the outlet behind the whirlpool, and within 24″(610 mm) of
the pump.
Do not disassemble the pump or piping as this could void the
warranty.
Size the drain cutout to fit the drain assembly that will be
used.
End stud positioning is critical.
Studs should be positioned roughly as shown.
3-1/2"
(89 mm)
30" (762 mm)
3-1/8" (79 mm)
Overflow Detail
1-1/2"
(38 mm)
43-1/2"
(1105 mm)
24-1/2"
(622 mm)
8-3/4"
(222 mm)
8"
(203 mm)
3"
(76 mm)
16"
(406 mm)
60"
(1524 mm)
19"
(483 mm)
20"
(508 mm)
42"
(1067 mm)
16"
(406 mm)
14"
(356 mm) 6" (152 mm)
(Typical)
43-1/2"
(1105 mm)
Ø 2" (51 mm) Drain
8-3/4"
(222 mm)
60-1/8" (1527 mm) Min
60-1/4" (1530 mm) Max
17-1/4"
(438 mm)
Drain Cutout
4"
(102 mm)
Pump
Motor
Location
Recommended Support Clip
Location (4 Total)
Product Diagram
ENSEMBLETM
ENSEMBLETM 42″(1067 mm) WHIRLPOOL BATH
Page2of2
1021378-4-H