Sterling AFD Bath/Shower System 71110112 User manual

Features
•Compression molded from our exclusive solid Vikrell
®
material
•Gentle sloping back, neck, and armrest in bath
design
•Above-floor-drain (AFD) rough-in
•Factory installed injection molded apron extension
and undersupport structure
•Tongue-and-groove 4-piece modular design allows for
easy ″snap together″installation
•Durable high-gloss finish
•10-year consumer/3-year commercial limited warranty
•18-1/4″(464 mm) bath depth (floor to top of
threshold)
•60-1/4″(1530 mm) x 43-1/2″(1105 mm) x 75-1/2″
(1918 mm) complete unit rough-in dimensions include
flanges
•60″(1524 mm) x 42″(1067 mm) x 74-1/4″(1886
mm) complete unit finished dimensions
Codes/Standards Applicable
Specified model meets or exceeds the following:
•ASTM E162
•ASTM E662
•CSA B45.5/IAPMO Z124
42″(1067 mm) AFD BATH AND WALL
SURROUND
71110112
ALSO 71110119, 71110122, 71110129
Colors/Finishes
•0: White
•Other: Refer to Price Book for additional colors/finishes
Specified Model
Model Complete Unit Description Colors/Finishes
71110112 42″(1067 mm) AFD bath and wall surround, left drain ❑0❑Other_____
71110119 42″(1067 mm) AFD bath/shower with access panel system, left drain ❑0❑Other_____
71110122 42″(1067 mm) AFD bath and wall surround, right drain (shown) ❑0❑Other_____
71110129 42″(1067 mm) AFD bath/shower with access panel system, right drain ❑0❑Other_____
Model Wall Component Description Colors/Finishes
71114100 Complete wall set ❑0❑Other_____
ENSEMBLETM
Page 1 of 2
1021860-4-K
For more information
visit SterlingPlumbing.com
or call 1-800-STERLING

Technical Information
Fixture*:
Basin area:
Bathing well 40″(1016 mm) x 27″(686 mm)
Top area 52″(1321 mm) x 35″(889 mm)
To overflow:
Water depth 11″(279 mm)
Capacity 55 gal (208.2 L)
* Approximate measurements for comparison only.
Model Door width Door maximum
height
All 58-1/2″(1486 mm) 55-3/4″(1416 mm)
Installation Notes
Install this product according to the installation guide.
Size the drain hole clearance to fit the drain assembly that will
be used.
End stud positioning is critical.
Studs should be positioned roughly as shown.
60-1/8" (1527 mm) Min
60-1/4" (1530 mm) Max
3-1/2"
(89 mm)
30" (762 mm)
3-1/8" (79 mm)
Overflow
Detail
1-1/4"
(32 mm)
43-1/2"
(1105 mm)
27-1/2"
(699 mm)
4"
(102 mm)
8"
(203 mm)
53"
(1346 mm)
75-1/2"
(1918 mm)
3"
(76 mm)
18-1/4"
(464 mm)
60"
(1524 mm) 1-1/2"
(38 mm)
21-1/4"
(540 mm)
22-1/4"
(565 mm)
42"
(1067 mm)
16"
(406 mm)
14"
(356 mm)
6" (152 mm)
(Typical)
43-1/2"
(1105 mm) Ø 2" (51 mm) Drain
8-3/4"
(222 mm)
20-1/4"
(514 mm)
11-1/2"
(292 mm)
14"
(356 mm) Ø 2" (51 mm) Minimum Drain
Hole Clearance Through Wall
3" (76 mm) Drain
Bottom to Floor
Recommended Support Clip
Location (4 Total)
Product Diagram
ENSEMBLETM
ENSEMBLETM 42″(1067 mm) AFD BATH AND WALL SURROUND
Page2of2
1021860-4-K