Steve Silver TA600CB User manual

Your furniture purchase is an investment. Here are a few tips to maximize the lifetime of your furniture with a
minimal amount of effort. Properly caring for your furniture can help ensure that it looks great year after year.
Wood Furniture Maintenance:
- Always dust, wipe, and clean with the grain of the
wood.
- Dust with a soft cloth. Dust will scratch the
furniture surface if not removed properly.
- If a polished surface becomes cloudy, rub it with a
cloth dipped in a solution of one tablespoon
vinegar to one quart of water. Rub softly with the
grain until the surface is completely dry.
- Soap and water are not advisable for wood
surfaces. Water can penetrate the finish and raise
the grain on wood, causing damage.
- Remember to change dusting cloths frequently as
dirty cloths may scratch your furniture’s surface.
The Enemies of Wood:
- Moisture is wood’s worst enemy. Liquid spills
should be gently wiped up immediately. Coasters
should be used under all beverages.
- Do not allow rubber or vinyl materials to lie on the
furniture. Chemicals in rubber may leave a stain.
Put a strip of felt or leather under accessories that
have rubber or vinyl.
- Heat creates a chemical change in the furniture’s
finish, which may result in a white spot. Use
protective pads under hot dishes, appliances, etc.
- Sunlight’s ultraviolet rays can damage the finish
of furniture. Do not place furniture directly
against a heater or radiator and do not place in the
path of hot streams of air from central heating.
This will cause extreme localized drying of the
wood.
Marble Top Maintenance:
The surface of the marble on your table has been
polished andsealed to create a generally non-porous
surface. The stone has many natural characteristics
including veining, hairline cracks, and color variations,
which make up the stone’s beauty.
To maintain the beauty of your marble:
- Protect surfaces from scratching, staining and
etching by:
 Keeping them free of debris or sharp
objects.
 Wiping up spills immediately
 Avoiding contact with chemicals
(particularly acid-based materials)
- Clean with PH neutral products or those
especially formulated for use on stone.
- It is not recommended to use a water-based
solvent for dark marble as it will remove the
polish from the surface.
Caring for the Fabric on Upholstered Furniture:
- Frequent vacuuming of the entire upholstered
area will prevent dust from settling into the fibers.
- Professional cleaning is always recommended for
all upholstered pieces.
- Do not use cleaning products containing
brightening agents.
ITEM # TA600CB
TAHOE COUNTER BENCH
57” X 15” X 24”

STEP# 1:Put the Legs(2)toWooden Top(1). STEP#2:Tighten the bolts to lock the legs as shown
below.
STEP#3: Put Stretcher(3)between e Legs(2)
.
STEP#4:Tighten the bolts to lock the stretcher as
2
1
2
3
ITEM # TA600CB
Assembly Instruction
Put all screws in loosely at first.
Do not tighten screws & bolts until the entire item is completely assembled.
Note: More than 2 people assemble required
Shown below.
the Legs(2)

Hardware Pack # PTA600CBH
A 5 MM 1 PC.
B 25 X 8 MM 18 PCS.
C 9 MM 18 PCS.
D 8 X 20 MM 18 PCS.
E 40 X 40 X 5 MM 4 PCS
F 100 X 40 X 5 MM 2PCS

LEVELER
PTA600CBLEV
LEG
PANEL
PTA
600CBL
P
STRETCHER
PTA600CBS
PARTS FOR TA600CB
COMPLETE HARDWARE # PTA600CBH
PRODUCT DETAILS
BENCH TOP ACACIA WOOD
LEGS ACACIA WOOD
STRETCHER IRON
LEVELER PLASTIC + IRON
SEAT HEIGHT 24”
SEAT DEPTH 15”
PRODUCT SIZE 57” X 15” X 24''
CARTON SIZE 60.50” X 18.50” X 7''
NET WEIGHT 57.320 LBS
GROSS WEIGHT 69.440 LBS
CU. FT. 4.53
MADE IN INDIA

Steve Silver Company Dining Chairs
Assembly Troubleshooting Guide
The most important element of correct chair assembly is to tighten the bolts as directed. Prematurely
tightening the bolts can lead to numerous issues and will lengthen the assembly time. Listed below are the
most common issues in chair assembly and their easy solutions.
PROBLEM: Chair is unlevel.
Cause 1:
Unlevel chairs can occur if the bolts are fully tightened before all bolts are attached. There is a variance in the
alignment of this chair to allow the chair to be assembled more easily.
Solution:
Loosen each bolt in the seat box (front legs, back corner blocks and back apron) until they are finger tight.
Place the chair upright on the floor. Sit in the chair for about 30 seconds. Carefully turn the chair upside down
and tighten each bolt. The chair will now be level.
Cause 2:
Unlevel chairs can occur if one or more of the floor glides are missing from the bottom of the chair leg.
Solution:
Request a set of floor glides from the e-mail address below.
PROBLEM: Bolts do not fit properly.
Cause:
This issue can occur when the bolts are tightened fully before all bolts are attached. There is a variance in the
alignment of the bolts to allow the chair to be assembled more easily. Tightening the bolts prematurely can
cause the holes for the other bolts to become slightly misaligned, causing the remaining bolts not to fit
properly.
Solution:
Make sure each bolt in the seat box (front legs, back corner blocks and back apron) is loosened until finger
tight. This will allow you to realign the holes, and the bolts will not fit properly.
Questions?
Please reach us at 800-344-7278 or [email protected], and we will be happy to help you.