Steve Silver CV500SG User manual

Canova Side Chair
19.5'' x 24.5“ x38''H
Your furniture purchase is an investment. Here are a few tips to maximize the lifetime of your furniture with a
minimal amount of effort. Properly caring for your furniture can help ensure that it looks great year after year.
Wood Furniture Maintenance:
-Always dust, wipe, and clean with the grain of
the wood.
-Dust with a soft cloth. Dust will scratch the
furniture surface if not removed properly.
-If a polished surface becomes foggy, rub it with a
cloth dipped in a solution of one tablespoon
vinegar to one quart of water. Rub softly with the
grain until the surface is completely dry.
-Soap and water are not advisable for wood
surfaces. Water can penetrate the finish and raise
the grain on wood, causing damage.
-Remember to change dusting cloths frequently as
dirty cloths may scratch your furniture’s surface.
The Enemies of Wood:
-Moisture is wood’s worst enemy. Liquid spills
should be gently wiped up immediately. Coasters
should be used under all beverages.
-Do not allow rubber or vinyl materials to lie on
the furniture. Chemicals in rubber may leave a
stain. Put a strip of felt or leather under
accessories that have rubber or vinyl.
-Heat creates a chemical change in the furniture’s
finish, which result in a white spot. Use
protective pads under hot dishes, appliances, etc.
-Sunlight’s ultraviolet rays can damage the finish
of furniture. Do not place furniture directly
against a heater or radiator and do not place in
the path of hot streams of air from central heating.
This will cause extreme localized drying of the
wood.
Marble Top Maintenance:
The surface of the marble on your table has been
polished and sealed to create a generally non-porous
surface. The stone has many natural characteristics
including veining, hairline cracks, and color variations,
which make up the stone’s beauty.
To maintain the beauty of your marble:
-Protect surfaces from scratching, staining and
etching by:
•Keeping them free of debris or sharp
objects.
•Wiping up spills immediately
•Avoiding contact with chemicals
(particularly acid-based materials)
-Clean with PH neutral products or those
especially formulated for use on stone.
-It is not recommended to use a water-based
solvent for dark marble as it will remove the
polish from the surface.
Caring for the Fabric on Upholstered Furniture:
-Frequent vacuuming of the entire upholstered
area will prevent dust from settling into the
fibers.
-Professional cleaning is always recommended
for all upholstered pieces.
-Do not use cleaning products containing
brightening agents.
ITEM#: CV500SG

B
EC
D
F
CV500SG
ASSEMBLYINSTRUCTION
Do not fully tightenscrews& boltsuntil theentireitemiscompletelyassembled
B
E
D
F
A
E
D
F
E
C
D
F
A
E
D
F
E
D
F
STEP:1 STEP:2
STEP:3 STEP:4

1PC
PCV500SGH
HardwarePack#
A4PCS
B
C
D
E
F
4PCS
3PCS
11PCS
5/16"
11PCS
12mm
5/16"
5/16"×3–1/4"
5/16"×2-1/4"
5/16"×1-1/2"

PCV500SGL
CHAIR BACK
PCV500SGLEV
PCV500SGB
36.96 LBS
PARTS FOR
CompleteHardware#:
PRODUCTDETAILS
PRODUCTSIZE
CARTONSIZE
NET WEIGHT
GROSS WEIGHT
CV500SG
PCV500SGH
Leg
PCV500SGSC
Chair Back
CU.FT.
Seat cushion
LEG / SEAT FRAME
42.60 LBS
7.02'
19.5"X24.5"X38"
MADE IN CHINA
Leveler
WHITE VERTEBRAL WOOD+FABRIC+FOAM
WHITE VERTEBRAL WOOD
LEVELER PLASTIC+ IRON
41.25"x21"x14"
SEAT CUSHION MDF+FABRIC+FOAM
SEAT HEIGHT
SEAT DEPTH
19"
18"
PCV500SGSF
Seat Frame
CV500SG

Steve Silver Company Dining Chairs
Assembly Troubleshooting Guide
The most important element of correct chair assembly is to tighten the bolts as directed. Prematurely
tightening the bolts can lead to numerous issues and will lengthen the assembly time. Listed below are the
most common issues in chair assembly and their easy solutions.
PROBLEM: Chair is unlevel.
Cause 1:
Unlevel chairs can occur if the bolts are fully tightened before allbolts are attached. There is a variance in the
alignment of this chair to allow the chair to be assembled more easily.
Solution:
Loosen each bolt in the seatbox (front legs,back corner blocks and backapron) until theyarefinger tight.
Place the chair upright on the floor. Sit in the chair for about 30 seconds. Carefully turn the chair upside down
and tighten each bolt. The chair will now be level.
Cause 2:
Unlevel chairs can occurif one or more ofthe floor glides are missingfrom the bottom of the chair leg.
Solution:
Request a set of floor glides from the e-mail address below.
PROBLEM: Bolts do not fit properly.
Cause:
This issue can occur when the bolts are tightened fully before allbolts are attached. There is a variance in the
alignment of the bolts to allow the chair to be assembled more easily. Tightening the bolts prematurely can
cause the holes for the other bolts to become slightly misaligned, causing the remaining bolts not to fit
properly.
Solution:
Make sure each bolt in the seat box (front legs, back corner blocks and back apron) is loosened until finger
tight. This will allow you to realign the holes, and the bolts will not fit properly.
Questions?
Please reach us at 800-344-7278 or [e-mail], and we will be happy to help you.