Techni Mobili RTA-1565 User manual

MODEL RTA-1565

RTA-1565
DIMENSIONS
MAXIMUM WEIGHT CAPACITIES
DO NOT exceed this limit
Please use care and good judgement
when placing objects on wood surface
Product Size: 47"W x 24"D x 30"H

P.3
x2 x6
x2
x2 x2 x2
x3
Structure Top support tube Screw stud T type tube
Horizontal bar Glass tabletop Top drawer front panel
Small drawer left panel Top drawer right panel Drawer bottom panel Small drawer back panel

P.4
x3
x2
x4
Sliders Handle Middle drawer front panel Bracket and nut, SET
File drawer front panel File drawer left panel File drawer right panel File drawer back panel
File drawer tube Locking fittings Left panel
Right panel Middle panel Bottom panel Back panel
Cabinet top panel Bottom support tube Caster

P.5
Cam lock
Cam bolt
1. 2. 3.
Screw the bolt into the
corresponding panel.
In the other panel, insert
and align the cam lock.
Join the panels.
Turn the cam lock.
MISALIGNED:
TURN CAM LOCK
TO POINT TOWARDS
THE HOLE
CORRECT
HOW TO ASSEMBLE USING BOLTS AND CAM LOCKS:
32
If the panel already comes with the cam lock inserted, make sure is aligned:

P.6
GENERAL ASSEMBLY TIPS AND TROUBLESHOOTING DURING ASSEMBLY:
*Before you start assembling, make sure you have all the parts and necessary
hardware by doing a quick inventory.
*Follow the assembly instructions step by step, and do not skip any unless
advised to do so by RTA PRODUCTS’ Customer Service.
*On each step, and to avoid misalignments, always leave screws loose, and
do not tighten them until all are in place.
*In wood panels, the laminate might be covering the holes.
If there are no visible holes: Pass the tip of your finger around the area where
the hole should be, and press against the surface to feel the indentation.
If the hole looks too small for the screw of bolt: carefully perforate the laminate
with the tip of a pen.
DOES THE HOLE
LOOK TOO SMALL?
CAREFULLY
PERFORATE. THE HOLE IS BIGGER
THAN WHAT IT APPEARED.
*In wood panels, some might have inserts that look like screws. Those inserts are
either nuts or cam locks. Make sure they are aligned to receive the screws or bolts.
Misaligned
nut CORRECT Misaligned
cam lock CORRECT
*Make sure to use the correct screws or bolts, and do not overtight them.
Using wrong screws or overtighting them might cause damage to the parts,
and such damage is not covered by the product’s warranty.
30mm
30mm
35mm
35mm
CORRECT SIZE OF SCREW
SCREW IS NOT OVERTIGHTEN A WRONG SIZE OF SCREW
OR OVERTIGHTING IT WILL
CAUSE DAMAGE!

P.7
Place the bar (21E) inside the channel of
panel (23) with the tubes towards the top
of the panel, and secure the fittings (21A)
to the panel using screws (A).
Insert the metal fittings into
the bar (21E) in the following
order: (21A)x1, (21C)x3, (21A)x1.
Then tighten the (21C) on the
marked positions of the bar (21E).
Grab all the flat shaped sliders (12) and set aside the “L” shaped ones. Assemble the sliders to the
inside face of side panels (22) and (23) using screws (A). The wheels will be located at the front and
facing down.
If you don’t see the holes, pass the tip of your finger around the area where
the holes should be, pressing against the surface to feel the indentation.

P.8
22
23
26
24
25
SCREWS
14PCS
6X40 MM
B
22 23
27
SCREWS
6PCS
6X40 MM
B
SCREWS
4PCS
8X30 MM
G
6
2
SCREWS
H
2PCS
6X20 MM
25
3
3
3
3
28 X4
4
56
7
Screw (G) to each
corner on the underside
of the cabinet, then
attach (28) to them.
Finally, attach the
studs (3).
Screw the bolts (B) to the corresponding holes on the inside face of panels (22) and (23),
then assemble the panels to (24), (25) and (26) by turning all the corresponding cam locks.
Screw the bolts (B) to the bottom face of
panel (27), then assemble it to the cabinet
by turning the
corresponding
cam locks.
Carefully place the glass tabletop (6) upside-down as shown in the figure, and screw (H)
to the 2 round mounting discs on the left end, then attach the tubes (2) to them.

P.9
Attach the studs (3) to the structure (1) using the wrench to tighten them.
Then assemble the horizontal bars (5) to the structure (1)
and the T type tube (4) using screws (F) as shown.
DO NOT TIGHTEN THE SCREWS AFTER DONE WITH
STEP #9!
With the frame built in step #8 upside-down,
secure the horizontal bars (5) with screws (F)
as shown. Proceed to tighten all screws (F).
Place the washer (K) over the left hole on the top of
the cabinet, and place over it the frame built in step #9,
making sure the holes align. Secure the frame
using screw (I) from inside the cabinet as shown.

P.10
Place the washers (K) over the holes on the
right side of the top of the cabinet, and
carefully place the glass tabletop (6) over the
frame and cabinet as shown. Secure the glass
with screws (I) for the cabinet, and (J) for the
frame.
DO NOT TIGHTEN
ANY SCREWS
UNTIL ALL
ARE IN PLACE!
Attach the lock fittings (21B) to the outside face of panels (9) and (18), using screws (A).
Screw bolts (B) to the holes on the inside face of panels (7) and (14). Then assemble the side
panels (8) and (9) to both panels (7) and (14) as shown by turning the cam locks.

P.11
Slide the bottom panels (10)
thru the channels in between
panels (8), (9) and (7)/(14) as
shown. Make sure the panel
fits inside all the channels.
Assemble the back panels (11) in the between the side panels (8) and (9) using screws (C) as shown.
Place the small drawers upside-down.
Grab the “L” shaped sliders (12) and assemble
them to the drawers using screws (A), with
the wheels facing towards the back of the
drawers. Make sure the sliders are
touching the side panels, and that they
are not “up in the air”.

P.12
7
21D
21G
7
Assemble the handles (13) to the small drawers using screws (D) as shown.
Assemble the lock (21D) and ring (21G) to the panel (7) of the top drawer using screws (A).
IMPORTANT: The rod on the lock MUST face down, and the
lock MUST turn counter-clockwise with the key.
Assemble the bracket (15) to the bottom of the inside face of panel (16)
using screws (E) and (F) as shown. Then attach the caster (29) to the
bracket using the nut and tighten with the wrench.

P.13
Screw the bolts (B) to
the inside face of panel
(16) as shown. Then
assemble the panels (17)
and (18) by turning the
cam lock.
Slide the bottom panel (10) thru the channels
in between panels (16), (17) and (18) as
shown. Make sure the panel fits inside all the
channels.
Assemble the back panel (19) to the
side panels (17) and (18) using
screws (C) as shown.
Carefully insert the file tubes (20) thru the
back panel (19) and screw them into the insert
of the front panel (16).
WARNING: DO NOT OVERTIGHTEN the tubes
as it may perforate and damage the front panel.
Such damage is not covered by the product’s
warranty.
Place the file drawer upside-down. Grab the “L” shaped sliders (12) and assemble them to the
drawer using screws (A), with the wheels facing towards the back of the drawers. Make sure the
sliders are touching the side panels, and that they are not “up in the air”.

P.14
Assemble the handle (13) to the file drawer using screws (D) as shown.
Carefully insert all the drawers starting from the bottom. Make sure the wheels from the drawers
engage and roll in the middle of the sliders.
FINISHED!
ENJOY YOUR NEW UNIT!

English
- DO NOT EXPOSE THE SURFACES TO DIRECT SUNLIGHT, OR
EXTREME ENVIRONMENTAL CONDITIONS. EXPOSURE WILL
DAMAGE THE PRODUCT, WHICH IS NOT COVERED BY THE
WARRANTY.
- DO NOT USE SOLVENTS OVER SURFACES OR STRUCTURAL
TUBES. SURFACES MUST BE CLEANED WITH A SOLUTION OF
A SMOOTH SOAP AND WATER, THEN CLEARED WITH A DRY
TOWEL.
- PRODUCTS THAT ARE HEAVY SHOULD BE LIFTED OR MOVED
BY AT LEAST 2 PERSONS, AND ALL OBJECTS SHOULD BE
REMOVED FROM THE PRODUCT.
CARE AND MAINTENANCE