STI 7535MED Original operating instructions

QUICK INSTALLATION OF STI-7535MED
All specifications and information shown were current as of publication and are subject to change without notice.
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: [phone] • Fax: [phone]
Toll Free: 800-888-4784 • E-mail: [email protected]
Web: www.sti-usa.com
Taylor House • 34 Sherwood Road • Bromsgrove
Worcestershire • B60 3DR • England
Tel: [phone] • Fax: [phone]
E-mail: [email protected] • Web: www.sti-emea.com
7535MEDISO QUICK MAY2008
INSERT ALL (4) TABS INTO
SLOTS IN ENCLOSURE
STEP 1
CENTER PLATE OVER HOLE IN TOP
OF CABINET WHERE WIRES EXIT.
MARK AND DRILL (2) 3/16 in.
DIAMETER HOLES IN WALL.
STEP 3 SELECT–ALERT KEY
SWITCH PLATE 09723
STEP 2
PLACE ENCLOSURE ON WALL AND
MARK ALL (4) HOLE LOCATIONS.
REMOVE ENCLOSURE FROM WALL.
DRILL (4) 1/4 in. DIAMETER
HOLES IN WALL.
INSERT ALL (4) ANCHORS INTO WALL.
MOUNT ENCLOSURE ON WALL
USING THE (4) #10 x 1-1/2 in. SCREWS.
#10 x 1-1/2 in. SCREWS
MAKE SURE REED SWITCH WIRES
EXIT HOLE IN TOP SIDE OF CABINET.
INSERT ALL (4) TABS INTO
SLOTS IN ENCLOSURE
STEP 1
CENTER PLATE OVER HOLE IN TOP
OF CABINET WHERE WIRES EXIT.
MARK AND DRILL (2) 3/16 in.
DIAMETER HOLES IN WALL.
STEP 3 SELECT–ALERT KEY
SWITCH PLATE 09723
STEP 2
PLACE ENCLOSURE ON WALL AND
MARK ALL (4) HOLE LOCATIONS.
REMOVE ENCLOSURE FROM WALL.
DRILL (4) 1/4 in. DIAMETER
HOLES IN WALL.
INSERT ALL (4) ANCHORS INTO WALL.
MOUNT ENCLOSURE ON WALL
USING THE (4) #10 x
1-1/2 in. SCREWS.
#10 x 1-1/2 in. SCREWS
MAKE SURE REED SWITCH WIRES
EXIT HOLE IN TOP SIDE OF CABINET.
INSERT ALL (4) TABS INTO
SLOTS IN ENCLOSURE
STEP 1
CENTER PLATE OVER HOLE IN TOP
OF CABINET WHERE WIRES EXIT.
MARK AND DRILL (2) 3/16 in.
DIAMETER HOLES IN WALL.
STEP 3 SELECT–ALERT KEY
SWITCH PLATE 09723
STEP 2
PLACE ENCLOSURE ON WALL AND
MARK ALL (4) HOLE LOCATIONS.
REMOVE ENCLOSURE FROM WALL.
DRILL (4) 1/4 in. DIAMETER
HOLES IN WALL.
INSERT ALL (4) ANCHORS INTO WALL.
MOUNT ENCLOSURE ON WALL
USING THE (4) #10 x 1-1/2 in. SCREWS.
#10 x 1-1/2 in. SCREWS
MAKE SURE REED SWITCH WIRES
EXIT HOLE IN TOP SIDE OF CABINET.
WARNING: This product can expose you to chemicals including Dichloromethane, which is known to the
State of California to cause cancer, and Bisphenol A (BPA), which is known to the State of California to
cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Three year warranty or a one year limited warranty (from date of purchase) on most products. See
website for details. Electronic warranty form at www.sti-usa.com/wc14.
All manuals and user guides at all-guides.com
all-guides.com

2306 Airport Road • Waterford, Michigan 48327-1209
Phone: [phone] • Fax: [phone]
Toll Free: 800-888-4784 • E-mail: [email protected]
Web: www.sti-usa.com
Taylor House • 34 Sherwood Road • Bromsgrove
Worcestershire • B60 3DR • England
Tel: [phone] • Fax: [phone]
E-mail: [email protected] • Web: www.sti-emea.com
TERMINAL STRIP
BATTERY CONNECT
9 VDC BATTERY
#801 KEY
ELECTRONICS
LENS COVER
INSTALL PLASTIC ANCHORS INTO WALL.
ROUTE KEY SWITCH AND REED SWITCH WIRES FROM
BEHIND KEY SWITCH PLATE.
THRU HOLES IN BOTH PLATES (AS SHOWN).
ATTACH BOTH PLATES TO WALL WITH (2) #8 x 1-1/4 in. SCREWS.
(BE SURE ALL WIRES ARE PROTECTED FROM VIEW BEHIND KEY SWITCH PLATE).
STEP 4
REED SWITCH AND MAGNET
(INSTALL INSIDE CABINET)
REED SWITCH WIRE
19018 ANCHOR #8–10
3/16 DIAMETER HOLE (2) PLACES
KEY SWITCH WIRE
09723 KEY SWITCH PLATE
BASE PLATE
STEP 5
FEED WIRES THROUGH ELECTRONICS PLATE
MOUNT ELECTRONICS TO BASE PLATE.
CONNECT REED SWITCH AND KEY SWITCH WIRES TO TERMINAL STRIP.
CONNECT BATTERY.
INSTALL LENS COVER.
TURN KEY SWITCH ON.
OPEN CABINET DOOR TO TEST.
REFER TO INSTRUCTION MANUAL
FOR ALARM TIMING AND
SOUND ADJUSTMENTS.
NOTE:
TERMINAL STRIP
REED SWITCH WIRE
(NOT POLARITY SENSITIVE)
KEY SWITCH WIRE
(NOT POLARITY SENSITIVE)
DC IN
+-KEY
SWITCH ALARM
SWITCH NC COM NO
TERMINAL STRIP
BATTERY CONNECT
9 VDC BATTERY
#801 KEY
ELECTRONICS
LENS COVER
INSTALL PLASTIC ANCHORS INTO WALL.
ROUTE KEY SWITCH AND REED SWITCH WIRES FROM
BEHIND KEY SWITCH PLATE.
THRU HOLES IN BOTH PLATES (AS SHOWN).
ATTACH BOTH PLATES TO WALL WITH (2) #8 x 1-1/4 in. SCREWS.
(BE SURE ALL WIRES ARE PROTECTED FROM VIEW BEHIND KEY SWITCH PLATE).
STEP 4
REED SWITCH AND MAGNET
(INSTALL INSIDE CABINET)
REED SWITCH WIRE
19018 ANCHOR #8–10
3/16 DIAMETER HOLE (2) PLACES
KEY SWITCH WIRE
09723 KEY SWITCH PLATE
BASE PLATE
STEP 5
FEED WIRES THROUGH ELECTRONICS PLATE
MOUNT ELECTRONICS TO BASE PLATE.
CONNECT REED SWITCH AND KEY SWITCH WIRES TO TERMINAL STRIP.
CONNECT BATTERY.
INSTALL LENS COVER.
TURN KEY SWITCH ON.
OPEN CABINET DOOR TO TEST.
REFER TO INSTRUCTION MANUAL
FOR ALARM TIMING AND
SOUND ADJUSTMENTS.
NOTE:
TERMINAL STRIP
REED SWITCH WIRE
(NOT POLARITY SENSITIVE)
KEY SWITCH WIRE
(NOT POLARITY SENSITIVE)
DC IN
+-KEY
SWITCH ALARM
SWITCH NC COM NO
TERMINAL STRIP
BATTERY CONNECT
9 VDC BATTERY
#801 KEY
ELECTRONICS
LENS COVER
INSTALL PLASTIC ANCHORS INTO WALL.
ROUTE KEY SWITCH AND REED SWITCH WIRES FROM
BEHIND KEY SWITCH PLATE.
THRU HOLES IN BOTH PLATES (AS SHOWN).
ATTACH BOTH PLATES TO WALL WITH (2) #8 x 1-1/4 in. SCREWS.
(BE SURE ALL WIRES ARE PROTECTED FROM VIEW BEHIND KEY SWITCH PLATE).
STEP 4
REED SWITCH AND MAGNET
(INSTALL INSIDE CABINET)
REED SWITCH WIRE
19018 ANCHOR #8–10
3/16 DIAMETER HOLE (2) PLACES
KEY SWITCH WIRE
09723 KEY SWITCH PLATE
BASE PLATE
STEP 5
FEED WIRES THROUGH ELECTRONICS PLATE
MOUNT ELECTRONICS TO BASE PLATE.
CONNECT REED SWITCH AND KEY SWITCH WIRES TO TERMINAL STRIP.
CONNECT BATTERY.
INSTALL LENS COVER.
TURN KEY SWITCH ON.
OPEN CABINET DOOR TO TEST.
REFER TO INSTRUCTION MANUAL
FOR ALARM TIMING AND
SOUND ADJUSTMENTS.
NOTE:
TERMINAL STRIP
REED SWITCH WIRE
(NOT POLARITY SENSITIVE)
KEY SWITCH WIRE
(NOT POLARITY SENSITIVE)
DC IN
+-KEY
SWITCH ALARM
SWITCH NC COM NO
STEP 4
INSTALL PLASTIC ANCHORS INTO WALL.
ROUTE KEY SWITCH AND REED SWITCH WIRES FROM BEHIND KEY
SWITCH PLATE THROUGH HOLES IN BOTH PLATES (AS SHOWN).
ATTACH BOTH PLATES TO WALL WITH (2) #8 x 1-1/4 in. SCREWS.
(BE SURE ALL WIRES ARE PROTECTED FROM VIEW BEHIND KEY
SWITCH PLATE.)
STEP 5
FEED WIRES THROUGH ELECTRONICS PLATE
MOUNT ELECTRONICS TO BASE PLATE.
CONNECT REED SWITCH WIRES TO TERMINAL STRIP.
CONNECT BATTERY.
INSTALL LENS COVER.
CLOSE CABINET DOOR.
TURN KEY SWITCH ON.
OPEN CABINET DOOR TO TEST.
MAY 2008 7535MED QUICK INSTALL
All manuals and user guides at all-guides.com