Streak Ultra ETORQUE X1 User manual

X1 MID-TOWER GAMING CASE
X4 MID-TOWER GAMING CASE
User Manual

Table of Contents
1. Contents
1.1 Accessory X1,X4 3
2. Installation instructions
2.1 Side Panel Disassembly 3
2.2 Motherboard Installation 4
2.3 5.25” Device Installation 5
2.4 2.5” HDD Installation 6
2.5 External 3.5” Device Installation 7
2.6 Power Supply Installation 8
2.7 Fan Installation 8
2.8 Removing the Top of the chassis X4 8
2.9 Front I/O Installation Guide 9

3
1. Contents
1.1 Accessory X1 & X4
- Installation Guide x 1 (X1, X4)
- Screw Bag x 1 (X1, X4)
- HDD rail (X1 * 2pcs, X4 * 4pcs)
- 5.25” to 3.5” Drive Bay Cover (X1 only)
- Cable Tie x 9 (X4 only)
2. Installation instructions
2.1 Side Panel Disassembly
Remove the thumb screws from the rear side of the case and pull the
side panel rearwards.
To close again place the side panel into the guide rails and push it
forwards with care, then screw in the two thumb screws on the rear
side.

4
2.2 Motherboard Installation
Install the I/O panel that comes with your motherboard package.
Secure the standoffs on the motherboard tray.
Install the motherboard in proper location and secure it with provided
screws.
NOTE: CPU, RAM and any
peripheral installation are not
included in this manual. Please
refer to your motherboard
manual for related mounting
instructions and troubleshooting.

5
2.3 5.25” Device Installation
From the interior of the case, use a firm device of your choice to push
the 5.25” drive bay cover out.
Take out the plastic holding clips from both sides of the drive cage by
turning the unlocking mechanism to the left.
Insert the 5.25” device into the drive bay.
Match the ODD drive holes with the drive cage.
Insert the plastic clips and turn it clockwise to lock it in place.

6
2.4 2.5” HDD/SSD Installation
Remove the 2.5” SSD hard drive tray by pushing the tray tab to the
right to release the tray.
Place 2.5” SSD hard drive into the hard drive box. Close the box.
Slide the 2.5” SSD hard drive box into the chassis.
Find the 4-Pin Molex on the power supply and connect it to the
backplane. Connect the backplane to motherboard with SATA cable.

7
2.5 3.5” HDD Installation
X1 only:
Placing the hard drive in the drive cage and secure with the provided
screws.
X4 only:
Find the HD rails in the accessory box, and fix them in both sides of
the 3.5” drive. Insert the drive and rails into chassis.

8
2.6 Power Supply Installation
Place the power supply and secure it with the provided screws.
2.7 Side Panel Fan Installation
Place the fan in the side panel and secure with the provided screws.
2.8 Removing the Top of the chassis : X4 only
Remove the thumb screws on the back of chassis to open the top.
Up to 2 x 120mm fans or 240mm radiator can be installed on the upper
part of chassis.

9
2.9 Front I/O Installation Guide
Please refer to the following illustration of front I/O connector and your
motherboard user manual.
USB 3.0
USB 2.0
HD Audio

10
Streak Products, Inc. • www.ultraproducts.com
© 2013 Streak Products, Inc.
Ultra® is a registered trademark and Ultra ETORQUE™ is a trademark of
Streak Products, Inc.
8300 West Flagler Street, #121-106, Miami, FL 33144
All other trademarks listed are the property of their respective owners.
Streak Products is not responsible for typographical or photographic errors.
TECHNICAL SUPPORT [phone]
WARNING: Keep out of reach of children-contains sharp edges that may
harm children.