Streamline SFC05-09 User manual

INSTRUCTION
MANUAL
STREAMLINE
SFC05 - 09
SFC16
Codes:
INSTR-SFC
®

®
2W: www.streamline.systems E: [e-mail] T: [phone] W: www.streamline.systems E: [e-mail] T: [phone]
• STREAMLINE® systems can be built according to customers’ exact requirements
• For non-standard systems, the user’s needs or specifications are listened to and turned
into reality.
• Whilst price is important, quality is remembered long after price is forgotten
• We insist on sourcing brand name products from around the world, only of a reputable
quality, and bring them together under the STREAMLINE® name
• All STREAMLINE® products carry a full one year’s warranty, according to the manufacturers’
standard terms and conditions of sale.
• We have an in-house technical helpline able to answer most of your questions relating to the
capabilities and functionalities of all STREAMLINE® products
• If we get it wrong, we will put it right. If you are sent a wrong item, we will immediately
attend to sending you the correct item and arrange a collection of the wrong item without
any quibbles
• STREAMLINE® is backed by a comprehensive range with massive stocks providing you with a
‘one stop shop’ for all your requirements.
Flexibility
Quality
Service
Why STREAMLINE®?
MANUFACTURED
IN THE
UNITED KINGDOM
CHECKED AND
TESTED BY
QUALITY CONTROL
Contents
1. Why STREAMLINE®?
2. STREAMLINE® Warranty
4. Operating Warnings
5. Set Up Auto Calibrate
6. Operation
3. Wiring
1Why STREAMLINE®
Controller Messages
3
4
5
6
7 - 8
9
10
STREAMLINE
®

®
4W: www.streamline.systems E: [e-mail] T: [phone] W: www.streamline.systems E: [e-mail] T: [phone]
V16
STREAMLINE® Warranty Wiring
The warranty on all Machines and Equipment is
for 1 year (12-months) from RECORDED DATE
OF PURCHASE.
THIS WARRANTY EXCLUDES NORMAL
MAINTENANCE ITEMS, including but not limited
to HOSES, FILTERS, O-RINGS,
DIAPHRAGMS, VALVES, GASKETS,
CARBON BRUSHES and damage to motors
and other components as a result of failure to
replace normal maintenance items. THIS LIST
IS NOT EXHAUSTIVE.
If STREAMLINE® receives notice of such defects
during the warranty period, STREAMLINE®
will either, at its opinion, repair or replace
components which prove to be defective.
Replacement parts will only be supplied under
warranty, upon the inspection and approval of
the defective parts by STREAMLINE®.
Should it be necessary to supply replacement
parts before the opportunity to inspect, these
will be charged at current prices and credit will
only be issued upon subsequent inspection and
warranty approval by STREAMLINE®.
The customer is responsible for the cost of
return of the defective part. If warranty is
approved, STREAMLINE® will pay for the cost
of the repaired or replacement part.
This warranty excludes the following conditions
and circumstances which are at the discretion
of STREAMLINE®:
Wear and tear, misuse, abuse improper
maintenance, frost damage, the use of chemicals
other than those supplied or approved by
STREAMLINE®, improper installation or repair,
unauthorised modification, incidental or
consequential costs, loss or damage, service,
labour or third party charges, the cost of
returning defective parts to STREAMLINE®.
This warranty constitutes the exclusive remedy
of any purchaser of a STREAMLINE® unit and
is in lieu of all other warranties, express or
implied, including without limitation any implied
warranty of merchantability or fitness for use, to
the fullest extent permitted by law. In no event
shall any implied warranty of merchantability or
fitness for use exceed the term of the applicable
warranty stated above and STREAMLINE® shall
have no other obligation or liability.
Important
Unfortunately these rights cannot be
transferred to a third party.
2STREAMLINE®Warranty
Important
The Fuse for this unit is a 10A Fuse. Make sure correct fuse is fitted in-line, close
to the battery end of the RED (positive) wire. Failure to do so will result in
damage to the unit.
Connect the pump controller in accordance with this diagram.
NOTE: only fit the fuse once all connections are made
3Wiring
Enter Button
Down / Up Buttons
Fuse 10A
12V Battery Pump
Power Button
Display
STREAMLINE
®

®
6W: www.streamline.systems E: [e-mail] T: [phone] W: www.streamline.systems E: [e-mail] T: [phone]
4Operating Warnings
Operating Warnings Set Up Auto Calibrate
Important
Your battery is at risk of permanent damage if you disable low battery cut-o
and continue to use your controller for long periods when the battery voltage
has fallen below +10.5V.
Adjust the flow settings carefully. Repeated false dead-end detection indicates that the Cal value
should be increased (less sensitive).
For safety wire through the pump pressure switch. (The pressure switch can be bypassed if
absolutely necessary - the unit will protect itself under normal conditions.)
This is a WATER PUMP controller: it will not work with air in the system. Always prime the system
before starting work. If air in the system causes false dead-end detection, increase Cal value until air
is removed.
Do not set the Cal value too high. Setting it higher than necessary places extra strain on both the
pump and the controller in a dead end situation. This can result in damage to both the pump and
your controller.
Specification Value
Supply Voltage 11 - 15 VDC
Maximum Current 15A
Typical Drive Current 8A
Voltmeter Accuracy + - 100mV
Enclosure Material ABS
Water Resistance IP65
Dimensions 115 x 65 x 40 (mm)
Working Temperature 0 - 40 Deg C
5Set Up Auto Calibrate
Connect your hose and pole + brush to the pump.
Turn on the controller by pressing the power button.
Press and hold the up and enter buttons to
calibrate. CAL will be displayed.
To select Auto Cal continue to press the down
button until AUt is displayed. Press the enter
button to start. Auto Cal starts from C99.
After several moments the calculated CAL value
(e.g. C50) will be displayed and the controller is
ready to use. Press enter to exit calibration.
Press up until the display shows 30.
DisplayButton
STREAMLINE

®
8W: www.streamline.systems E: [e-mail] T: [phone] W: www.streamline.systems E: [e-mail] T: [phone]
DisplayButton
The CAL value can be adjusted manually by
following the same steps and adjusting the CAL
value by pressing the up or down button instead
of using AUt.
To enable or disable the low battery cut-o*
(that stops your pump when the battery voltage
is below 10.5V) press and hold the down and
enter buttons.
Then use the up or down button to select ON or OFF. Press enter to save.
NOTE: ‘ON’ keeps your battery protected.
6Operation
To select Auto Cal continue to press the down
button until AUt is displayed. Press the enter
button to start. Auto Cal starts from C99.
DisplayButton
Press enter to display the current
battery voltage.
Press enter again to return to the current flow rate.
To turn the controller o, press the power button.
Operation
STREAMLINE

®
10 W: www.streamline.systems E: [e-mail] T: [phone] W: www.streamline.systems E: [e-mail] T: [phone]
An error has occurred while using AutoCal. This will
happen when the motor is not connected or the enter
button has been pressed to cancel it.
Pressure switch activated or pump disconnected
A dead end has been detected. If this is not the case,
try increasing the calibration value.
This message will start to flash when the battery is low
(<11.0V). If the battery is below 10.5V the pump will be
disabled to protect the battery (unless low battery cut-
o is disabled)
An over current has been detected, the controller has
shut down the pump to protect itself. Lower the flow
rate and check the hose for blockages.
Message Description
Controller Messages
Notes
STREAMLINE

Hamilton House, 8 Fairfax Road,
Heathfield Industrial Estate,
Newton Abbot
Devon, TQ12 6UD
United Kingdom
Telephone: [phone]
Email: [e-mail]
Visit www.streamline.systems