Streckfuss A075/Ri User manual

MODEL A075/Ri
OPERATING INSTRUCTIONS
Serial Number _
•
Tel: [phone] Fax: [phone]
Streckfuss
~=
Streckfuss USA, Inc
1401 Capital Ave. B
Plano, TX 75074

TABLE OF CONTENTS
A075/Ri
1.0 GENERAL DESCRIPTION 1
2.0 SETTING UP THE MACHINE .
3.0 ADJUSTMENTS
3.1 Body Thickness 1, 2
3.2 Lead Span 2, 3
4.0 OPERATION
4.1 Loading Input Tubes 3, 4
4.2 Loading Output Tubes 5
4.3 Control Panel 5, 6
5.0 PREVENTIVE MAINTENANCE
5.1 Daily 6
5.2 Weekly 6
6.0 TECHNICAL SPECIFICATIONS 6
7.0 ELECTRICAL DIAGRAM 7

1 0 GENERAL DESCRIPTION:
The Streckfuss model A075/Ri is designed to form the leads of dual in-line components utilizing a
tube-to-tube feeding configuration. Fully adjustable, the A075/Ri requires no die changes which
allows a wide range of component sizes to be processed quickly and easily. The lead span
adjustment is displayed on a digital panel meter and the operating speed is infinitely variable.
The component tubes are loaded onto an adjustable, input attachment and gravity fed to a foam
padded belt that indexes them through the forming process. The belt holds the components
securely against a set of infinitely variable guide rails. The forming action is performed by
adjustable rollers located on either side of the guide rails. After forming the components are then
deposited into a second tube for collection.
2 0 SETTING UP THE MACHINE:
1. Place the A075/Ri a suitable work surface.
2. Connect power cord coming from the back of the unit to an approved electrical service
rated for the appropriate voltage as indicated on the specification label.
3 0 ADJUSTMENTS:
3.1 Bodv Thickness
1. Place a component upside-down on the gauge block as shown in figure 1.
2. Turn the adjustment screw in the direction as needed until the gauge pin contacts the
component.
Mustment Knob ~
Gauge Pin
Gauge Block
Component
Figure 1
Page 2
A075/Ri

3 0 ADJUSTMENTS:
3.1 Body Thickness
3. Loosen the thumb screw securing the collar shown in figure 2.
4. Raise the collar until it contacts the linear bushing.
5. Re-tighten the thumb screw when finished.
Thumb Screw
Collar
Linear Bushing
Figure 2
3.2 Lead Span or "Pitch"
1. Set the panel meter selector switch to the 2 position.
Selector
Panel
Figure 3
3 0 ADJUSTMENTS:
3.2 Lead Span or "Pitch"
Page 3
A075/Ri

2. Turn the pitch adjustment knob in the direction as needed until the required setting
is displayed on the panel meter.
Note: In some cases components with the same part number from different vendors
may require different settings on the panel meter. This is due to variations in
the component from one vendor to the next.
Panel Meter
Pitch Adjustment
Figure 4
4 0 OPERATION:
4.1 Loadinq Input Tube
1. Lift upward on the tube retainer knob and turn the knob ~ turn to disengage the retaining
plate.
Lead In Rails
Tube Retainer Knob
Lead In Rail
Adjustment
Figure 5
2. Turn the lead in rail adjustment knob in the direction as needed until the bottom of the
tube slides easily onto the lead in rails. The tube should fit onto the rails without any
side to side play. Page 4
A075/Ri
4 0 OPERATION:
4.1 Loadinq Input Tube
3. Insert tube until it contacts the stop plate. The stop plate will keep the components in the
tube until they are presented to the guide rails.

Page 4
A075/Ri
4 0 OPERATION:
4.1 Loadinq Input Tube
3. Insert tube until it contacts the stop plate. The stop plate will keep the components in the
tube until they are presented to the guide rails.
Component Tube
Stop Plate
Guide <oils
Figure 6
4. While holding the tube against the stop plate, swing the tube attachment upward until
the components slide onto the guide rails.
Components Slide
Onto Guide <oils
Figure 7
Engagement Pin
Post
Swing Attachment Upward
5. Lift upward on the tube retainer knob and turn the knob Y-i turn to engage the retaining
plate. The pin protruding from the bottom of the knob should fit into the hole in the post.

Page 5
A075/Ri
4 0 OPERATION:
4.2 Loadinq Output Tube
1. Lift upward on the tube retainer knob and turn the knob ~ turn to disengage the retaining
plate.
Tube Retainer Knob
Output Tube
Figure 8
Lead InRoil
Adjustment Knob
2. Turn the lead in rail adjustment knob in the direction as needed until the bottom of the
tube slides easily onto the lead in rails. The tube should fit onto the rails without any
side to side play.
3. Insert the tube until it stops against the guide rails.
4. Lift upward on the tube retainer knob and turn the knob ~ turn to engage the retaining
plate. The pin protruding from the bottom of the knob should fit into the hole in the post.
4.3 Control Panel
1. Turn the speed control knob counter-clockwise to zero or the minimum setting.
2. Turn the power switch on to position "1".
Power Switch
Speed Control Knob
Figure 9

Page 6
A075/Ri
4 0 OPERATION:
4.3 Control Panel
3. Turn the speed control knob clockwise until the desired operating speed is reached.
4. After all the components have been transferred from the input tube to the output tube
turn the power switch off to "0".
5. Repeat the steps as described in sections 4.1 through 4.3 to process a new tube of
components.
5 0 PREVENTIVE MAINTENANCE:
5.1 Daily
1. Clean any debris from the machine using a brush or vacuum.
Weekly
1. Remove the back panel from the machine and clean any debris from the interior
of the machine.
2. Apply a light amount of a 10w Teflon® based oil to all guide shafts.
3. Check the transport belt for wear.
6 0 TECHNICAL SPECIFICATIONS:
Production Rate:
Machine Dimensions:
Electrical Requirements:
5000 pcs/hr
18.0" Lx 14.0" W x 15.0" H
458mm Lx 356mm W x 381mm H
110v, 60hz, 0.8kw
220v, 50hz, 0.12kw
PARAMETERS
A
~A
A: = .300" - .900" [7.62mm - 22.86mm]
B: = .100" [2.54mm]
Custom Parameters And Forming
Requirements Are Available Upon
Request.

Streckfuss USA, Inc
1401 Capital Ave. B
Plano, TX 75074
Tel: [phone] - Fax: [phone]
STRECKFUSS USA INC
RECOMMENDED SPARE PARTS
Model A075 Ri
June 1991
QTY. DESCRIPTION PART NUMBER
1ea. Spare Parts Kit P-A075-510
1ea. Transport Belt P-A075-001
1ea. Linear Bearing 10mmx38mm ) P-A075-011
1ea. Lamp 110v/2w 1.90010.037 ) P-Lamp-001
2ea. Fuse 1 amp GDA 1A) P-Fuse-018
1ea. Bearing 625 ZZ) P-Bearing-012
1ea. Bearing 608 ZZ) P-Bearing-022
WHEN ORDERING PARTS PLEASE SPECIFY MACHINE SERIAL NUMBER
NOTE - ALL Screws And Nuts Are Metric.