Studio Tools Wall Rail User manual

We strongly recommend the installation of the Wall Rail by a professional.
Especially if several Wall Rails are connected, a precise installation is required so that the
boards do not get stuck at the joints later on.
In case of any uncertainties or difficulty in understanding, please contact us before you start the assembly.
Diese Montageanleitung ist in Englisch verfasst. Falls Sie etwas nicht verstehen oder Unklarheiten bestehen,
kontaktieren Sie uns bitte bevor Sie mit der Montage beginnen.
Wall Rail
Assembly instructions
A
Magnetic screw cover (1x)
Felt strip (1x)
Dowels (5x) Left end cap (1x) Right end cap (1x)
Screws (5x)
Scope of delivery
Rail (1x)
B
C
D F1 F2E

Alignment tipsSee alignment tips See alignment tips ** *
Standard alignment
recommendation
Minimal height alignment
recommendation
!
The rail (A+B) allows you to use Studioboards
and all Layers in portrait and landscape format.
The following board sizes and formats can rest
against the felt strip (C).
- Studioboard: portrait and landscape
- Layer 1,4 m2: portrait and landscape
- Layer 0,8 m2: portrait
!
Minimum height for the rail (A+B)
when you want to use Studioboards in
both formats: landscape and portrait.
!
With structural solid walls (e.g. concrete), the Wall Rail may be loaded with a maximum of 50 kilos per running meter. For all other walls, the maximum load depends
on the load-bearing capacity of the wall. In this case, screws and dowels suitable for the specific wall must be used - and not the ones supplied within the scope of delivery.
Make sure that holes are permitted to be drilled in the appropriate places on the wall. We accept no liability for damage caused by (improper) assembly or disassembly of Wall Rail and felt strip.
✕
A+B A+B
C
1850 mm
2 Wall Rail | Assembly instructions
I
Felt strip
Use of felt strip is optional. It serves as additional protection for boards and
wall. If the board keeps hitting against the wall with a clacking noise, the distance
between board and wall is too large and the use of the felt strip is highly
recommended.
Consider the dimensions of the smallest board when attaching the felt strip (C).
This ensures that all boards – regardless of format – can rest against the felt strip.
Custom alignment
There are unlimited ways of aligning the rail (A+B) and the felt strip (C), which
can be customised according to the conditions of the room and the boards
being used. In this way, skirting boards, cable strips or radiators can all be taken
into consideration.
Add additional rails
seamlessly. You can string
as many rails together as
your wall is long.
If necessary, the
Wall Rail can also be
sawn to any custom
length, smaller than
2220 mm.
740 mm1260 mm
Decide on wall alignment of rail and felt strip

A + BA + D/E
!
With structural solid walls (e.g. concrete), the Wall Rail may be loaded with a maximum of 50 kilos per running meter. For all other walls, the maximum load depends
on the load-bearing capacity of the wall. In this case, screws and dowels suitable for the specific wall must be used - and not the ones supplied within the scope of delivery.
Make sure that holes are permitted to be drilled in the appropriate places on the wall. We accept no liability for damage caused by (improper) assembly or disassembly of Wall Rail and felt strip.
5x D 5x E
A
B
A
D
D
D
D
D
E
E
E
E
E
D
A
E
B
3 Wall Rail | Assembly instructions
Attach magnetic screw cover to railII IIIMount rail on wall

1x F1 1x F2
A + F1/F2
!
With structural solid walls (e.g. concrete), the Wall Rail may be loaded with a maximum of 50 kilos per running meter. For all other walls, the maximum load depends
on the load-bearing capacity of the wall. In this case, screws and dowels suitable for the specific wall must be used - and not the ones supplied within the scope of delivery.
Make sure that holes are permitted to be drilled in the appropriate places on the wall. We accept no liability for damage caused by (improper) assembly or disassembly of Wall Rail and felt strip.
!
The felt strip protects the wall and board. The usage is optional but
recommended. For the best possible adhesive strength of the felt strip,
do not remove the entire protective tape right at the beginning,
but piece by piece when sticking it to the wall.
VFix felt strip
A
F2
A
F2
A
F2
A
C
A
F1
F2
3 Wall Rail | Assembly instructions
Attach end caps to both ends of railIV