STYLE STUDIO ROMAN User manual

Fitting Instructions
FITTING & CARE INSTRUCTIONS
1. Fitting tools required include star point
screwdriver, drill and drill bit suitable for
substrate.
2. Mark with a pencil where the brackets are to
be fixed. Brackets should be positioned approx.
50mm from the end of the headrail at each end.
For larger blinds, additional brackets will be
supplied and can be spaced evenly throughout
the width of the headrail.
3. Drill hole in substrate at each marked position.
If required, fit wall plugs. Position brackets at
window or fascia, ensure they are level and screw fix.
4. Slowly remove the velco fixing attaching the
fabric on your blind to the headrail. This will help
install the rail onto the brackets. Insert the headrail
whilst pushing the plastic button as shown in
diagram.
Ensure that the headrail groove is properly places
in the bracket lock and then release the button.
Secure fabric back onto headrail ensuring the top
fabric covers the brackets.
1
2
Fitting your device
The length of the operating chain allowed on the blind is dependent on both the installation height and the drop of
the blind. The blind will be supplied in accordance with the information opposite, depending on what information was
Fitting of Child Safety Devices
1. To fit your device, place the
chain round the device at the
maximum distance possible from
the control mechanism and mark
hole position on substrate. Make
sure the chain is fully taut.
2. Drill pilot hole and screw device
into position. Use applicable wall
plugs if required.
3. Ensure the distance between
the two strands of chain is not
more than 50mm at the point of
exit from the device.
Fitting of Child Safety Devices
GROUND GROUND
INSTALLATION HEIGHT KNOWN INSTALLATION HEIGHT UNKNOWN
TENSIONING DEVICE
1. To fit your device, place the
chain round the device at the
maximum distance possible
from the control mechanism and
mark hole position on substrate.
Make sure the chain is fully taut.
2. Drill pilot hole and screw
device into position. Use
applicable wall plugs if required.
3. Ensure the distance between
the two strands of chain is not
more than 50mm at the point of
exit from the device.
Young children can be strangled by loops in pull cords, chains, tapes and inner cords that operate
the product.
To avoid strangulation and entanglement, keep cords out of reach of young children. Cords
may become wrapped around a child’s neck.
All of our blinds are compliant with the Child Safety Legislation BS EN 13120 and are supplied with the
relevant child safety devices and labels to keep you and your family safe.
If you have any questions about the safety of your blind, please ask your retailer or installer.
Child Safety
CHILD SAFE
PRODUCT
.
.
Child Safety Devices
Your blind is supplied with either a face or recess fix child safety device as well as rear cord breakaway connectors
placed on the cords on the back of the blind.
The face/recess fix device is designed to hold the chain under tension, removing any potential loops.
The rear cord breakaway connectors are attached to each panel and cord on the reverse of the blind, and will break
away if any reasonable weight is placed on the cord on the back of the blind. The clip on the tape will remain in place
and the clip on the cord will breakaway, removing any potential cord loops.

Refitting your blind
• Lay the blind out on a flat surface. Place the headrail at top of the blind and unroll the cords.
Refit the breakaway cord connector.
•Slide the support rods into the tapes and the bottom bar into the pocket.
Dressing your Roman Blind
The so fabric nature of Roman Blinds means that they can require dressing in your window to obtain
a full, luxurious appearance.
Once your blind is fitted, we recommend steaming, adjusting and dressing your fabric to ensure your
new product looks it’s best in your window.
Caring for your blind - Removing your Roman Blind
• Remove your Roman blind from its brackets and lay on a flat surface, print side down. If required,
unscrew your tension device.
•Separate the blind from the headrail. This is attached by Velcro tape and should easily unfasten.
Disconnect the breakaway cord connectors on the rear of the blind.
•Carefully roll up the cords and secure with an elastic band.
•Remove the support rods from the tapes and remove bottom bar from the pocket.
Washing Instructions
For washing instructions, please refer to your local retailer.
Do not machine wash, dry clean only.
Operating your blind
To raise/lower your blind, pull the chain on the blind as required.
Motorised
Use the supplied Remote Control to raise and
lower your blind.
Or use the new Powershade Smart Controller -
an innovative app compatible with all current
Powershade products.
•Control your motorised blinds from your
smartphone device
•Available for iOS and Android
•Compatible with Amazon Alexa, Google
Home and Siri Shortcuts to integrate into
your home
Powershade Smart
Controller Hub