Dometic SKYSCREEN 2 User manual

Important: Place in owner's manual
SKYSCREEN
ROLLER CONCEALED 2
(Including Trims)
Fitting Instructions
Please read before beginning installation
Unit must be Installed so that it can be
Removed for Servicing
Model No:
Date:
...................................
...................................

Page 2 of 8© Dometic Uk Blind Systems Ltd 2019
Upper and Lower Trim
• Fit the upper trim rst.
• Locate the blind around the upper trim sitting the bottom edge of the upper trim on the top lip on the
inner face of the side rails.
• The blind cassette and upper trim is then held in position using 4 screws, one in each corner
(Hole A).
• The blind must not be distorted when installed as this can cause excess friction and might make the
blind jam.
• Ensure that the lower edge of the upper trim and the upper edge of the lower trim are square to the
blind and the correct length.
• Cut a recess for the button housing in the lower trim using the information provided on pages 5 or 6
(trims supplied by Oceanair are pre-cut)
• The ange on the button housing should sit against the inside face of the lower trim.
• Fit the headlining to the lower ange of the side rails (Face B) using Velcro or other xings. If the
headlining is lower than the ange then use spacers as necessary.
• Fit the lower trim aligning the cutouts with the button housings and sitting the upper edge to the
lower lip on the side rails.
• An alternative method is the optinal “Wood lower trim secret xing kit” which suspends the lower trim
from the button housings. (page 4)
• IMPORTANT: The unit must be installed in such a way that it can be removed for servicing.
• Do not screw into the roller housing for any reason as this will damage the fabric.
Fitting, Care & Maintenance Instructions
Installation
Lower Trim Button Housing
Roller housing
Headlining
Roller cover section
Fixing hole A
Side Rail
Face B
Side railUpper trim
Side rail lips
Flange

Page 3 of 8© Dometic Uk Blind Systems Ltd 2019
• To unlock - push the button which will eject the crossbar enabling you to operate the blind using the
handle slots in the crossbar.
• Draw the blind or yscreen to the opposite side until the magnets on the crossbars touch and hold
together
• To open - push crossbars apart which will force the magnets apart and enable the blind or yscreen
to be returned to its recess – should you let go of a crossbar the springs in the ends will give a
cushioned landing. The crossbars require pushing back into their recesses against the springs to
lock them home ush.
Operation
• Light lubrication of the runners ensure a smooth operation - never use a grease or oil - a silicon
spray is ideal.
• The fabric is a coated polyester woven fabric. If it gets wet pull out the blind and leave to dry
naturally. Small marks can be removed using an eraser.
• In the event of either the blind or the screen being damaged either part may be replaced. For
spare parts see parts list on page 7.
• Instructions are available for servicing and re-tensioning (which involves disassembly)
from Oceanair.
• For further information or installation assistance, please contact your local distributor.
Care & Maintenance

Page 4 of 8© Dometic Uk Blind Systems Ltd 2019
Wood Lower Trim Secret Fixing Kit
Step 3 t button housing
Screw cap
Lower trim
Button housing
Screw
Secret xing
bracket
Screw
Headlining
Upper trim
Roller cover
Side rail
Step 1 t secret xing bracket to lower trim
Step 2 position lower trim

Page 5 of 8© Dometic Uk Blind Systems Ltd 2019
Wood trim cut out dimensions and positioning for single Button
Housing (blinds under 800mm)
R10
R3/8”
R10
R3/8”
56mm
23/16”
17mm
11/16”
56mm
23/16”
17mm
11/16”
L
C
L
C

Page 6 of 8© Dometic Uk Blind Systems Ltd 2019
R10 R3/8”
56mm 23/16”
17mm 11/16”
L
C
R10 R3/8”
56mm 23/16”
17mm 11/16”
L C
215mm
8 7/16”
215mm
8 7/16”
215mm
8 7/16”
215mm
8 7/16”
800 - 1200mm
31 - 47”
Wood trim cut out dimensions and positioning for two button housings
(blinds over 800mm)

Page 7 of 8© Dometic Uk Blind Systems Ltd 2019
No. Part No. Description
1 12828960005 Roller Cover
2 11808770005 Side Rail
3 10053150000 Roller
4 11872660005 Crossbar
5 11808600000 Magnet
6 11808830004 Brush Strip (please specify length)
7 400000526 Cloth Strip
8 50020520000 Double sided Tape
9 41860030000 LH Endplate
10 41860040000 RH Endplate
11 40065410000 Spring
12 41872360003 Button Housing (White)
41866590003 Button Housing (Dark Grey)
400000173 Button Housing (Chrome)
13 41872360003 Button Housing Screw Cap (White) (4 off)
41866590003 Button Housing Screw Cap (Dark Grey) (4 off)
14 41872380003 Button
No. Part No. Description
15 41872380003 Plate Bearing
16 41872380003 LH Pusher
17 41872380003 RH Pusher
18 41872370003 LH Crossbar End cap
19 41872370003 RH Crossbar End cap
20 41872370003 Hook
21 400001890 Roller Bearing
22 4180950000 Hook Spring
23 41814310000 Pusher Spring (4 off)
24 43668490000 M4 Clinch Nut (4 off)
25 400000625 M3 x 4 mm Screw (8 off)
26 41872550000 M4 x 12 mm Screw (4 off)
27 40062100000 No. 6 x 19mm Screw (16 off)
28 10104970001 Flyscreen Fabric (1 off)
29 See Fabric Collection Blackout Fabric (1 off)
30 Build Dependant Aluminium Liner (1 off)
31 Build Dependant Wood Liner (1 off)
• All Parts 2 off unless stated
• For SKYSCREEN with Wood trim omit item 30.
• For SKYSCREEN with Aluminium Liner, omit item 29.
8
76 3
4
9
13
11
10
12
5
28
17
16
14
19 2
115
24
26
25
29
23
31
30
21
20
18
27
6
22
Parts List

700000058 Issue 03 February 2019
www.dometic.com
blindsyst[email protected]
© Dometic UK Blind Systems Ltd 2019 [phone]