Sumake ST-BS110A User manual

SUMAKE PNEUMATIC TOOLS
Air Belt Sander (6x330mm)
ST-BS110A
SUMAKE INDUSTRIAL CO., LTD
4F,NO.351,Yangguang St.,Neihu District TAIPEI, TAIWAN, ZIP:114-91
Noise and Vibration:
Vibration
EN ISO 28927-3
Noise
EN ISO 15744
Remark
No Load:
1.64 m/s²
Sound Pressure Level
load: 85 dB(A)
Please always
wear ear
protector at
environment
noise level > 80
dB(A) due to
risk of impaired
hearing!
Sound power level
load: 96 dB(A)
Uncertainty
K= 1.5 m/s²
Uncertainty
K= 3dB
Specification:
Free Speed
17,000 r/min
Sanding Pad
6/25”x 13”
(6mm x 330mm)
Air Consumption
17 CFM (480 L/min)
Overall Length
12-3/5” (320 mm)
Air Inlet (PT)
1/4” (6.35 mm)
Air Hose (I.D.)
3/8” (10 mm)
Air Pressure
90 psi (6.3 bar)
Net Weight
1.8 lbs (0.82 kg)
ST-BS110A-S-2310C-D5F

EC DECLARATION OF CONFORMITY
We: SUMAKE INDUSTRIAL CO., LTD.
4F, No. 351, Yangguang St., Neihu District, Taipei City, Taiwan
declare in sole responsibility that the equipment
Equipment：AIR BELT SANDER (6x330mm)
Model/ Serial No.： ST-BS110A
to which this declaration applies, complies with these normative documents:
Machinery Directive: 2006/42/EC
and conforms to the following EN standard,
EN ISO 12100: 2010
EN ISO 11148-8:2011
Name and Signature/Position Date and Place
2022/12/1
Mike Su – Managing Director Taipei, Taiwan
ST-BS110A-D-2306B-D5F

ST-BS110A-I-2104A-D5
Foreword
SUMAKE is a manufacturer and exporter of air
tools since established. We have devote all our
efforts in improving quality and tools’ life. As
well as the noise and vibration of tools. Bring all
of you working efficiences, profits, and enjoy
using the tool is our principle.
Features
1. Finishing of flat surfaces, curved surfaces, and
corner can be freely performed by changing the
shoe.
2. Since it is small, lightweight, and balanced so
that the grinding surface is stable, extremely fine
finishing is possible.
3. The grinding speed can be freely adjusted by
raising or lowing the lever according to the
application.
4. Rear exhaust eliminates flying dust and noise.
Operator‘s instruction
1. Main Applications
Finishing metal carts and products.
Finishing welded surface.
Trimming parts.
Filleting.
Finishing steel cabinets and furniture.
Foundation finishing prior to coating.
Finishing plastic products, glass, and
earthenware.
Finishing stone and decorative wood products.
Finishing sashes and other building material.
Light and medium duty auto, ship and aircraft
finishing.
2. Cautions for Use
2-1 Air pressure
Maximum performance is displayed at the proper
sanding speed, obtainable at a gauge pressure of
6.2 bar. Range-wise, this is an air pressure from
5 to 7 bar (70 to 100 psi)
57
2-2 Air line
Use a 3/8“ air hose between the compressor and
the tool . Compressed air is cooled and its water
content separated, as soon as the air leaves the
compressor. A portion of the water content,
however, is condensed in the piping, and can
enter the tool mechanism, and may cause trouble.
So, install an air filter and on oiler between the
compressor and the tool. Use a 3 HP or larger
compressor for each sander.
Tool
Nipple
Coupler Recoil
hose
Leader
hose
Oiler Regulator
Water
separation Air
supply
Drain
daily
2-3 Air hose
Clean the hose with a blast of compressed air
before connecting the hose to air tool. This will
prevent both moisture and dust within the hose
from entering the tool and causing possible rust
or malfunction. To compensate for unusually
long hose (over 25 ft), the line pressure should be
increased accordingly.
Drainage
2-4 Sandpaper
The specification of sandpaper ranges from # 40
to # 200. Also note that, the maximum operating
speed which the sandpaper can afford shall be
higher than the rotation speed of this tool.
2-5 The approved eye protector,ear-muff,
mouth-muffle, and gloves shall be worn when
operate this tool.
2-6 The working place shall be ventilative.
2-7 Release the on-off device in the case of
energy supply failure.
3. Operation, Adjusting And Replacing
Method
3.1 On-off device
The on-off device is under the grip of this tool. It
is a “hold-to-run” type. You can also adjusting
the running speed by raising or lowering the lever.
This tool stops rotation within few sec, after
releasing the lever. For the sake of safety, put it
on a soft cloth or on hanger after it completely
stops.
3.2 Replace the sandbelt
Disengage and remove the sandbelt from the idle
pulley after pushing the idle pulley in the
direction shown below. Replace a new one and
keep your hand away from the idle pulley. Then
push the tension bar indicated on the drawing and
the sandbelt will be propped into the ready
position.
idlepulley tension bar
3.3 Adjusting tracking
If the sandbelt is not centered on the idle pulley,
adjust the hexagon socket head bolt on the idle
pulley bracket with accessory hexagon wrench
key until centering is correct. Turn the hexagon
socket counter clockwise, the belt is moved
toward the bracket, and vice versa.
clockwise
counterclockwise
bracket
4. Maintenance
4-1 Lubrication
Before connecting the hose , apply 4 or 5 drops
of #60 spindle oil at the air inlet. Use of a thicker
oil can lead to reduced performance or
malfunction. If a
thicker oil is used by accident, wash it away
immediately. Also, every 3 or 4 hours of
operation, oiling is necessary.
4-2 Storage
Avoid storing the tool in a location subject to
high humidity. If the tool is left as it is used , the
residual moisture inside the tool can cause rust.
Before storing and after operation, oil the tool at
the air inlet with spindle oil and run it for a short
4-3 Disposal
If the tool is too seriously damaged to be used
anymore, drop it in a resource recycling can.
Never drop it into fire.
4-4 Ordering service Parts
For further operational and handling information
or for replacement of parts and components,
contact the sale agent from whom you purchased
the tool or the service division of our company.
*In ordering parts and components, give each
part number, name and quantity.
Warning
1. This tool is not insulted for coming into
contact with electric power source.
2. It is forbidden to use this tool in explosive
atmospheres and do not put any combustible
material near the workpiece since it emit sparks
when grind with metal material.
3. Ensure that the sandbelt is on the central of
idle pulley and not to fix too tight/loose. Too
tight tends to break off and too loose tends to
break away.
4. Prevent long hair or loose clothing from
drawing in while operate this tool.
5. Never carry the tool by hose and beware of a
whipping compressed air hose.
6. Rotating action can cause this tool to become
hot. Allow to cool and disconnect air hose before
any changing or adjusting.

ST-BS110A
AIR BELT SANDER (6x330mm)
PARTS LIST
No. Parts No. Description Q'ty No. Parts No. Description Q'ty
1 BS110A-01 Idle Pulley 1 34 BS110E-34 Parallel Key Both Ends Round 1
2 BS110A-02 Bearing (683ZZ) 2 35 BS110E-35 Rotor Blade 5
3 BS110A-03 Idle Pulley Screw 1 36 BS110E-36 Cylinder 1
5 BS110A-05 Bracket 6 1 37 BS110E-37 Rear End Plate 1
6 BS110A-06 Set Screw 1 38 BS110E-38 Ball Bearing (608ZZ) 1
7 BS110A-07 Hexagon Socket Headless Set Screw 139 BS110E-39 O-Ring 1
8 BS110A-08 Spring 1 40 BS110E-40 Cap 1
9 BS110A-09 Tension Bar 1 41 BS110E-41 Spring Pin 1
14 BS110E-14 Stopper Pin 1 42A BS110E-42A Safety Throttle Lever 1
15 BS110E-15 Guard Bushing 1 43 BS110E-43 Valve Spring 1
16 BS110E-16 Tension Spring 1 44 BS110E-44 O-Ring (P3) 1
17 BS110A-17 Guard Body 1 45 BS110E-45 Valve Stem 1
18 BS110E-18 Head Cap Screw (M5×15) 1 46 BS110E-46 O-Ring (ID3x1) 1
19 BS110E-19 Dust Cover 1 47 BS110E-47 O-Ring (ID8.8x1.9) 1
20 BS110A-20 Shoe 6 1 48 BS110E-48 O-Ring (S011.2) 1
21 BS110E-21 Hexagon Socket Headless Set Screw 149 BS110E-49 Valve Body 1
22 BS110E-22 Stopper Spring 1 50 BS110E-50 Air Regulator 1
23 BS110E-23 Stopper 1 51 BS110E-51 O-Ring (P7) 2
24 BS110E-24 Spring Pin 1 52 BS110E-52 Snap Ring 1
25 BS110E-25 Pulley Cover 1 53 BS110E-53 Muffler 1
26 BS110E-26 Hexagon Nut 1 54 BS110E-54 Exhaust Diffuser 1
27 BS110E-27 Washer 1 55 BS110E-55 Inlet Bushing 1
28 BS110E-28 Drive Pulley 1 58 BS110E-58 Hex. Wrench (1.5mm) 1
29 BS110E-29 Housing 159 BS110E-59 Hex. Wrench (4.0mm) 1
30 BS110E-30 Ball Bearing (6000ZZ) 1 BS110A-60A Grinding Belt (#100x6) 1
31 BS110E-31 Front End Plate 1 BS110A-60B Grinding Belt (#80) 1
32 BS110E-32 Spacer 1 BS110A-60C Grinding Belt (#120) 1
33 BS110E-33 Rotor 1
ST-BS110A-P-2110B-D5
60